Ultra Start 2250M - Manuals

Page 2 - To Enter Diagnostic Mode:; Clear Diagnostic Memory.; DIAGNOSTICS; PARK LIGHTS STATUS LED DIAGNOSTIC CODE; NSTALLATION; WIRING DIAGRAM

2250 Wiring Diagram Page 3Pre-Installation Page 4 Components Recommended Pre-Installation ProceduresRecommended Install Procedures Wire Connectors Page 5 6 Pin Connector14 Pin Connector3 Pin Red Connector4 Pin Blue Connector Jumper Selections Installation Page 6 Basic Installation - Quick startPlugg...

Page 3 - Blue; SIDE VIEW; ACTIVE RF ANTENNA; Jumpers; Note: The default setting is second ignition.; Status Led’s; **The antenna must be connected before the system will operate

YELLOW WHITE/BLUE BLACK BROWN RED/WHITE PURPLE BLUE/WHITE PINK BLACK/WHITE BLUE WHITE GREEN/WHITE GREEN ORANGE 4 PIN Blue SIDE VIEW ACTIVE RF ANTENNA Jumpers The jumpers control the output on the white wire from the six pin harness. Place the jumpers in the above order to change the output. Note: Th...

Page 4 - . Check for obstructions on both; Components; INSTALLATION GUIDE; INSTALLATION TIPS

Recommended Pre-Installation Procedures - Control module - Remote transmitter(s) - Antenna with built in program button and LED’s - 6 pin main harness with dual 30amp power inputs - 14 pin harness - 3 pin - 2 wire keyless entry harness - Multi-tone siren - Hood pin safety switch - Hood and window st...

Page 5 - 4 Pin Connector; Pin Power Connector

Yellow Starter 30amp output 12volts during crank only. Green Heater 30amp output 12volts in accessory. Off during start. Red 12 power 30amp input Constant 12volt power at ignition harness. Red 12 power 30amp input Constant 12volt power at ignition harness. Blue Ignition 1 30amp output 12volts in ign...

Page 6 - PROGRAMMING

QUICK START INSTALL QUICK START INSTALL Yellow Starter Output Connect The Yellow Wire From The 6 Pin To The Vehicles Starter Wire. Green Heater Output Connect The Green Wire From The 6 Pin To The Vehicles Accessory Wire. Red 12 power Input Connect to Constant 12 Volt Power Source - High Current. Red...

Page 7 - QUICK START INSTALL; Programming Overview; as listed on pages 8 -; SYSTEM RESET; - Press and release the Program Button.; The system is now re-set to factory defaults.

QUICK START INSTALL Program mode allows you to adjust the settings and options of your system. Your system has been intelligently designed by installers with years of experience. The system’s default settings do not require any program changes in most cases. However, this system does incorporate a h...

Page 8 - Note: See Setting 7 to adjust the door lock pulse duration to 125ms.

PROGRAM MODE - USER SETTINGS 1 Double Pulse Unlock 1 Flash Single .75sec.Lock pulse and double Unlock Pulse 2 3 Second Lock & Unlock 2 Flashes 3 second pulses for Lock & Unlock *3 0.75 Second Pulses 3 Flashes 0.75 second pulses for Lock and Unlock 1 Ignition Lock & Unlock Enabled 1 Light...

Page 11 - Press button; times; During countdown; on; After full alarm; ENSURE THAT USER IS FULLY TRAINED ON THIS FEATURE!

PROGRAM MODE - TACH SETTINGS Setting 1- Method 2- Low Idle Tach Learning Setting 2- Adjust For Over-Crank (Tach or Tachless) Setting 3- Adjust For Under-Crank (Tach or Tachless) Shock Sensor - Self Learn Mode Anti Car Jacking Mode Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press th...

Page 12 - OPERATIONS

Manual Transmission Remote Starters must have both the door trigger and park brake wires connected. Most installs will require a clutch bypass. This is a temporary bypass. The clutch should only be bypassed during the activation of the remote starter. Never disconnect or alter the switch to be alway...

Page 13 - ACTIVATING SERVICE MODE; locks and trunk release are still operational.; DEACTIVATING SERVICE MODE; Remote start functions will return to normal operation.; System Service Mode; SERVICE MODE ACTIVATED; ) for 6 seconds until Status LED comes on Steady; SERVICE MODE DEACTIVATED; ) for 6 seconds until Status LED turns off.; LIMITED LIFETIME WARRANTY

ACTIVATING SERVICE MODE 1. While the ignition is “ON” press and hold the Program Button for five seconds. The park lights will flash and the siren will chirp five times to confirm that the system is in Service Mode. 2. While in Service Mode the remote start functions will be disabled and LED’s will ...

Page 14 - PANIC MODE DISABLE; Times if programmed for safety start

14 INSTALLATION GUIDE OPERATIONS OPERATIONS 1. Press and hold the # button for two seconds. 2. The system will flash the park lights and chirp the siren five times. **This feature can help find your vehicle in a crowded parking lot. 2 sec. 1.Press and hold the UNLOCK button for three seconds. 2. The...

Page 15 - Remote Stop; To Cancel Timer Mode:; Press and release the; Note: Opening a door after this point will cancel Reservation Mode.; Press and release the

INSTALLATION GUIDE OPERATIONS OPERATIONS Remote Start Remote Stop Idle Mode Turbo Timer Mode Timer Mode Self Learning Shock Sensor 1.Press and release the button. 2.The park lights will flash and the siren will chirp once.3.When the vehicle has started, the system will flash the park lights four tim...

Page 16 - Starter Kill with Bypass Units (Transponder or Passlock); Ignition

Blue Green Lock Un lock VehicleLock/UnlockSwitch To Control Relay or Actuators 87 86 85 87a 30 87 86 85 87a 30 87 86 85 87a 30 Lock Un lock VehicleLock/UnlockSwitch To Control Relay or Actuator Green Fused +12V Blue Orange 87 86 85 87a 30 87 86 85 87a 30 Blue Green Lock Un lock VehicleLock/UnlockSwi...