Turbosound LMS-A6 - Manuals

Page 2 - u s e r m a n u a l; CONTENTS

u s e r m a n u a l LMS-A6 LMS-A6 user manual Page 2 CONTENTS Important Safety Information ................................................................................................................. 3 Thanks .........................................................................................

Page 3 - Only use this equipment with an appropriate mains cord.

u s e r m a n u a l LMS-A6 LMS-A6 user manual Page 3 An example of this equipment has been tested and found to comply with thefollowing European and international Standards for ElectromagneticCompatibility and Electrical Safety: Radiated Emissions (EU): EN55013-1 (1996)RF Immunity (EU): EN55103-2 (1...

Page 4 - THANKS; We look forward to helping you in the near future.

u s e r m a n u a l LMS-A6 LMS-A6 user manual Page 4 THANKS Thank you for choosing the TURBOSOUND LMS-A6 for your application. Please spare a little timeto digest the contents of this manual, so that you obtain the best possible performance from thisunit. All TURBOSOUND products are carefully engine...

Page 5 - INTRODUCTION

u s e r m a n u a l LMS-A6 LMS-A6 user manual Page 5 INTRODUCTION The LMS-A6 is a versatile two input, six output, analogue loudspeaker management system in a1U rack mount package that is designed for maximum sonic performance. It combines crossoverand limiter functions and is uniquely configurable ...

Page 6 - FRONT PANEL FUNCTIONS

u s e r m a n u a l LMS-A6 LMS-A6 user manual Page 6 FRONT PANEL FUNCTIONS 1. Mono Band 1 Mono Band 1 Mono Band 1 Mono Band 1 – sums the Left and Right Band signals together (up position) and feeds them inmono to both Band 1 outputs. 2. Limiter cancel Limiter cancel Limiter cancel Limiter cancel – d...

Page 7 - REAR PANEL FUNCTIONS

u s e r m a n u a l LMS-A6 LMS-A6 user manual Page 7 REAR PANEL FUNCTIONS 1. Mains Power Mains Power Mains Power Mains Power - Connected via a standard IEC socket. A compatible power cord is supplied withthe unit. 2. Power Switch Power Switch Power Switch Power Switch. 3. Mains Fuse Mains Fuse Mains...

Page 9 - Connecting inputs and outputs

u s e r m a n u a l LMS-A6 LMS-A6 user manual Page 9 Connecting inputs and outputs This section describes how to connect signals to the LMS-A6 loudspeaker management system.The signal inputs are industry standard female XLR connectors and are wired as follows:- Pin 1 = GROUND or COMMON Pin 2 = HOT o...

Page 10 - Power On Standby Mode

u s e r m a n u a l LMS-A6 LMS-A6 user manual Page 10 Power On Standby Mode When power is first switched on the LMS-A6 enters STANDBY mode. In this mode all outputs aremuted to suppress any noise or transients while the circuitry settles down. The POWER STDBY switch determines how the unit will beha...

Page 11 - Level Trims

u s e r m a n u a l LMS-A6 LMS-A6 user manual Page 11 When this switch is up (on) the Left and Right Band 1 signals are summed together and fed inmono to both Band 1 outputs. When the switch is down the Left and Right Band 1 signals remain independent from each other. Level Trims Band 1 and Band 3 h...

Page 12 - Limiter Cancel

u s e r m a n u a l LMS-A6 LMS-A6 user manual Page 12 restrict the full undistorted output of the amplifiers. Note that the actual output power availableoften depends on the mains supply voltage, which may ‘sag’ during heavy performances. In a system where the amplifiers are capable of exceeding the...

Page 13 - TECHNICAL SPECIFICATIONS

u s e r m a n u a l LMS-A6 LMS-A6 user manual Page 13 TECHNICAL SPECIFICATIONS Inputs Inputs Inputs Inputs Two electronically balanced Impedance > 10k ohms CMRR >65dB 50Hz - 10kHz Outputs Outputs Outputs Outputs Six electronically balanced Source Imp < 60ohms Min. Load 600ohms Max. Level +2...

Page 14 - WARRANTY

u s e r m a n u a l LMS-A6 LMS-A6 user manual Page 14 WARRANTY This product is warranted against defects in components and workmanship only, for a period ofone year from the date of shipment to the end user. During the warranty period, TURBOSOUNDwill, at its discretion, either repair or replace prod...