Tricity Bendix TBG 640 - Manuals

6 HOB BURNERS To light a burner, push down the relevant controlknob and turn anticlockwise to maximum position. Atthe same time push the electric ignition button whichis marked with a little spark. Then adjust the flame asrequired.If the burner does not ignite, turn the control knob tozero, and try ...

7 Before any maintenance or cleaning can becarried out, you must DISCONNECT thehob from the electricity supply. The hob is best cleaned whilst it is still warm, asspillage can be removed more easily than if it is leftto cool. The Hob Top Regularly wipe over the hob top using a soft clothwell wrung o...

8 Something Not Working? SYMPTOM ■ There is no spark when lighting the gas ■ The gas ring burns unevenly SOLUTION ◆ Check that the unit is plugged in and the electrical supply is switched on ◆ Check that the RCCB has not tripped (if fitted) ◆ Check the mains fuse has not blown ◆ Check the burner cap...

9 If you require spare parts or an engineer contact yourlocal Service Force Centre by telephoning: 08705 929929 Your call will be routed to the Service Centrecovering your post code area. The addresses ofTricity Bendix Service Force Centres are detailed onthe following pages. CUSTOMER CARE For gener...

10 TRICITY BENDIX SERVICE FORCE To contact your local Tricity Bendix Service Force Centre telephone 08705 929 929 CHANNEL ISLANDS GUERNSEY Guernsey ElectricityPO Box 4Vale , Guernsey Channel Islands JERSEY Jersey ElectricityCompanyPO Box 45Queens RoadSt HelierJerseyChannel Islands JE4 8NY SCOTLAND A...

12 Ignition HT Spark Spark Generator Ispra Control's BF 50046 - 230-240V 0.6 YA T 120 Spark Gap Fixed OVERALL DIMENSIONS Width: 580 mm. Depth: 500 mm. Height: 88 mm. Burner Dia. Tap By-pass 1/100 mm Auxiliary 28 Semi-rapid 32 Rapid 40 Aeration adjustment none Instructions for the Installer CUT OUT D...

13 650 mm 420 mm 420 mm 100 mm 50 mm 50 mm 55 mm 600 mm Important safety requirements This hob must be installed in accordance with the GasSafety (Installation and Use) Regulations (CurrentEdition) and the IEE Wiring Regulations (CurrentEdition).Detailed recommendations are contained in thefollowing...

14 550 470 580 500 55 min. FO 2109 Rectangular cut-out size for hob A) End of shaft with nutB) WasherC) Elbow It is important to install the elbow correctly,with the shoulder on the end of the thread,fitted to the hob connecting pipe.Failure to ensure the correct assembly willcause leakage of gas. F...

15 Building In ON/OFF SWITCH FLEXOUTLET ON/OFF SWITCH FLEXOUTLET FO 0763 FO 0764 30 20 min 60 a b FO 1013 1 2 3 Dimensions are given in mm. Building over a cupboard or drawer If the hob is to be installed above a cupboard ordrawer it will be necessary to fit a heat resistant boardbelow the base of t...

16 Electrical connections Any electrical work required to install thishob should be carried out by a qualifiedelectrician or competent person, inaccordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liabilityshould these safety measures not beobserved. This...

17 B L N 0 1 2 3 4 220/240 A Wiring diagram A. IGNITOR SWITCH B. IGNITOR UNIT

18 Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK -Appliance must be electricallydisconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary. a) Test leads from any appliance earth point to earth pin on plug. Resistance shouldbe less than 0.1 Ω (Ohm), ch...

19 Ignition System / Gas Ignition YES Check plug top fuse andreplace if necessary Check polarity and earthcontinuity of supply point Check earth continuityof appliance Ignitor does not spark Check fitting of burners Check position of theelectrode Check by pass simmeradjusted Light burner manually Ch...

20 Commissioning When the hob has been fully installed it will benecessary to check the minimum flame setting. To dothis, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turnthe control knob from MIN to MAX several times...

21 Conversion from Natural Gas to LPG It is important to note that this model is designed foruse with natural gas but can be converted for use withbutane or propane gas providing the correct injectorsare fitted. The gas rate is adjusted to suit. Method • Ensure that the gas taps are in the 'OFF' pos...