TRENDNet Wireless 802.11g AP - Manuals

TRENDNet Wireless 802.11g AP – Manual in PDF format online.

Manuals:

Manual

Manual TRENDNet Wireless 802.11g AP

Summary

Page 2 - User’s Guide; Copyright Statement

User’s Guide 1 Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording, or otherwise without the prior writing of the publisher. July. 2003

Page 3 - Contents; Primary Setup ............................................................................................................7

User’s Guide 2 Contents 1. Introduction.............................................................................................................. 3 2. Safety Notification ................................................................................................... 4 3. Hardware Installatio...

Page 5 - Safety Notification; Please do not try to open or repair the device yourself.

User’s Guide 4 2. Safety Notification Your Wireless AP should be placed in a safe and secure location. To ensure proper operation, please keep the unit away from water and other damaging elements. Please read the user manual thoroughly before you install the device. The device should only be repaire...

Page 6 - Hardware Installation

User’s Guide 5 3. Hardware Installation Front Panel The front panel provides LED’s for device status. Refer to the following table for the meaning of each feature. LED STATUS Description Off No power Green On 1. Power on 2. Reset to default 3. Firmware upgrade (first 1 minute) PWR/STAT Green Blink 1...

Page 7 - Web Management Settings; admin”; TURN ON POWER SUPPLY

User’s Guide 6 4 Web Management Settings START UP & LOGIN In order to configure the Wireless 11g AP, you must use your web browser and manually input http:// 192.168.1.250 into the Address box and press Enter. The Main Page will appear. To start configure the Wireless 11g AP, you must login as “...

Page 8 - Primary Setup; This screen contains all of the AP's basic setup functions.; LAN IP Address and Subnet Mask:; This is the AP's IP Address and Subnet Mask as seen on the; MAKE CORRECT NETWORK SETTINGS OF YOUR COMPUTER; WEB management

User’s Guide 7 4.1. Primary Setup Primary Setup This screen contains all of the AP's basic setup functions. . Most users will be able to configure the AP and get it working properly using the settings on this screen. LAN IP Address and Subnet Mask: This is the AP's IP Address and Subnet Mask as seen...

Page 9 - This section provide the Wireless Network settings for your WLAN

User’s Guide 8 Wireless: This section provide the Wireless Network settings for your WLAN Wireless Settings SSID: The service set identifier ( SSID ) or network name. It is case sensitive and must not exceed 32 characters, which may be any keyboard character. You shall have selected the same SSID fo...

Page 10 - Important Notice

User’s Guide 9 -WPA-Preshared key There are two encryption options for WPA Pre-Shared Key, TKIP and AES. TKIP stands for Temporal Key Integrity Protocol. TKIP utilizes a stronger encryption method and incorporates Message Integrity Code (MIC) to provide protection against hackers. AES stands for Adv...

Page 13 - to wireless stations.

User’s Guide 12 4.3. Operating Mode Access Point: This mode provides access for wireless stations to wired LANs and from wired LANs to wireless stations.

Page 14 - enter the Remote Access Point’s MAC address to enable this feature.; Apply; to save your settings.

User’s Guide 13 AP Repeater: This mode allows the AP to keep the AP function role and at the same time performing a communication with other 802.11g AP to establish and extend your Wireless Network cover. Please enter the Remote Access Point’s MAC address to enable this feature. Wireless Bridge: Thi...

Page 15 - configuration type.; Refresh; button to refresh the AP's status and settings.

User’s Guide 14 4.4. Status This screen displays the IEEE 802.11g AP's current status and settings. This information is read-only. This page will auto re-flash every 5 seconds to keep most update information. LAN section will be displaying all information related on AP, such as the IP address and th...

Page 16 - feature is disabled by default. To keep activity logs, select; Enable; software. The AP will send updated logs to that PC.; View Log; Click the; button to save the setting.

User’s Guide 15 4.5 Traffic Log Traffic Log: The AP can keep logs of all incoming or outgoing traffic for your network traffic. This feature is disabled by default. To keep activity logs, select Enable . To keep a permanent record of activity logs as a file on your PC’s hard drive, Log viewer softwa...

Page 18 - Advanced Wireless; Authentication Type:

User’s Guide 17 4.7 Advanced Wireless Authentication Type: Auto: Auto is the default authentication algorithm. It will change its authentication type automatically to fulfill client’s requirement. Open System: Open System authentication is not required to be successful while a client may decline to ...

Page 19 - acknowledge the right to begin transmission.; Fragmentation Threshold:; This value specifies the maximum size for a packet before data is

User’s Guide 18 RTS Threshold: This value should remain at its default setting of 2346. Should you encounter inconsistent data flow, only minor modifications are recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. The AP sends Re...

Page 21 - Firmware Upgrade; button to load new firmware onto the AP. If the AP; Browse; button to find the firmware upgrade file.

User’s Guide 20 4.9. Upgrade Firmware To perform the firmware upgrade action, please go to the System section. Firmware Upgrade: Click the Firmware Upgrade button to load new firmware onto the AP. If the AP is not experiencing difficulties, then there is no need to download a more recent firmware ve...

Page 23 - Basic Functions

User’s Guide 22 5 . Troubleshooting Basic Functions My Wireless AP will not turn on. No LED’s light up. Cause: The power is not connected. Resolution: Connect the power adapter to your AP and plug it into the power outlet. Note: Only use the power adapter provided with your AP. Using any other adapt...

Page 24 - Wireless Troubleshooting; IP Address is not set correctly.; Technical Support; TRENDware Technical Support

User’s Guide 23 Wireless Troubleshooting I can’t access the Wireless AP from a wireless network card Cause: Out of range. IP Address is not set correctly. Resolution: Make sure that the Mode, SSID, Channel and encryption settings are set the same on each wireless adapter. Make sure that your compute...