TRENDNet TVIP600 - Manuals

TV-IP600/W Wireless Network Camera 2 1 Introduction Thank you for purchasing the TV-IP600/TV-IP600W Pan/Tilt (Wireless) Internet Camera, a standalone system that can be connected directly to an Ethernet or Fast Ethernet connection. The TV-IP600W also supports wireless transmissions based on the IEEE...

TV-IP600/W Wireless Network Camera 3 Unpacking the Package Open the shipping carton and carefully remove all items. Check that you have the following: • One TV-IP600 or TV-IP600W Internet Camera Server • One Detachable Antenna (TV-IP600W only) • One Multi-Language Quick Installation Guide • One Inst...

TV-IP600/W Wireless Network Camera 4 System Requirements Networking • Local Area Network: 10Base-T Ethernet or 100Base-TX Fast Ethernet • Wireless Local Area Network: IEEE 802.11b/g Wireless LAN (TV-IP600W only) Computer • CPU: 1.3GHz or above • Memory: 128 MB or above • VGA Resolution: 1024 x 768 o...

TV-IP600/W Wireless Network Camera 5 Default Settings Use the default settings to access the web-based management software and live video display. Default configuration settings Username This is the Username you will be prompted to enter when you access the TV-IP600/W configuration screens using a W...

TV-IP600/W Wireless Network Camera 6 Camera Hardware Components This section provides information about the Camera’s hardware components: Front Panel Components Front panel of TV-IP600/W LED Indicators LNK This LED indicator lights steady orange when a valid Ethernet link is established. It blinks o...

TV-IP600/W Wireless Network Camera 7 Rear Panel Components The power connection to the camera when fitted with the Infrared lens is split between the camera body and lens using the power connection adapter cable attached to the infrared lens. All other cables connect to the camera at the rear panel....

TV-IP600/W Wireless Network Camera 8 2 Installing the Camera The camera is intended for indoor use. The camera, the power adapter and power source should be protected from water and moisture, excessive heat, direct sunlight and cold. Make sure the power adapter and its cord and the Ethernet cable ar...

TV-IP600/W Wireless Network Camera 9 Connect Ethernet Cable To connect the camera to your network, connect a Category 5 or better Ethernet cable to the network cable connector located on the camera’s left side panel, and then attach it to the network. The Ethernet port will automatically detect and ...

TV-IP600/W Wireless Network Camera 10 Reset Camera A manual reset can be conducted by following the procedure below. The reset button is located on the rear panel of the camera. To reset the system settings to factory defaults, please follow these steps: 1. Use a paper clip or similar object to hold...

TV-IP600/W Wireless Network Camera 11 3 Security To ensure the highest level of security and prevent unauthorized usage of the Camera, the Administrator account has exclusive access to the System Administration configuration settings. The Administrator account can create up to 64 users and configure...

TV-IP600/W Wireless Network Camera 12 4 Application The TV-IP600 / TV-IP600W camera can be applied in a wide range of applications, including: • Monitoring of local and remote places and objects, such as construction sites, hospitals, amusement parks, schools and day-care centers by using a web brow...

TV-IP600/W Wireless Network Camera 13 5 Using the Utility This chapter describes the software utilities for the IP Camera, including how to set up your Camera with the utility. The SetupWizard has a user-friendly interface that allows you to setup the Camera easily. SetupWizard This section describe...

TV-IP600/W Wireless Network Camera 15 5. The software will start to install. The following window appears, showing the progress of the installation: 6. When installation is complete the following window appears to confirm that the SetupWizard has installed successfully: • Click Close to exit the ins...

TV-IP600/W Wireless Network Camera 17 SetupWizard- Select Your Camera The following screen appears showing the cameras that have been found on your network: ƒ Click on the camera you want to configure. ƒ Click Next to continue.

TV-IP600/W Wireless Network Camera 18 SetupWizard- Authentication On the following screen type in the ID and Password that you will use to configuring the camera settings: ƒ Type a User ID in the ID field. ƒ Type a password for the User in the Password field. ƒ Click Next to continue.

TV-IP600/W Wireless Network Camera 19 SetupWizard- Change Password The following screen allows you to change the default admin password: Carry out the following if you want to change the admin password: ƒ Tick the Change Password checkbox ƒ Type in a New Password in the New Password field and confir...

TV-IP600/W Wireless Network Camera 22 SetupWizard- Select a Connection Option- DHCP If your connection method is DHCP, click the DHCP radio button and click Next :

TV-IP600/W Wireless Network Camera 23 SetupWizard- Select a Connection Option- Fixed IP If your connection method is Fixed IP, click the Fixed IP radio button: The following window appears: ƒ Type in the IP Address, Subnet Mask, Default Gateway, Primary DNS Server IP address and Secondary DNS Server...

TV-IP600/W Wireless Network Camera 26 SetupWizard- Other Settings The following window allows you to configure additional camera settings: ƒ Type a name to help you identify the camera in the Camera Name field. ƒ Set the camera date and time from the Camera Time drop-down menus. To use the time sett...

TV-IP600/W Wireless Network Camera 27 SetupWizard- Setting Up The Camera The following window appears, summarizing the network settings of your camera: ƒ When you have finished setting up the Camera click the Next button. To make any changes to your Camera settings, click the Previous button. SetupW...

TV-IP600/W Wireless Network Camera 28 SetupWizard- Complete After the camera has restarted, the following window will appear: ƒ Click the hyper-link to connect to the camera web interface. ƒ If you want to setup an additional camera, click the Setup Another Camera button. ƒ When you have finished, c...

TV-IP600/W Wireless Network Camera 29 6 Using the Camera Web Manager The camera is easy to use and manage. Use a normal web browser to access the camera’s live video display, as well as the configuration software. It is recommended to check and make sure the computer can access and use the camera be...

TV-IP600/W Wireless Network Camera 30 Login To access the web manager directly from a computer or on a network without a DHCP server running, use the default IP address of the camera in the browser address entry to access the web manager. Type http://192.168.10.30 in the address bar and press Enter ...

TV-IP600/W Wireless Network Camera 31 Administration Click the ADMINISTRATION link to view the menus in the Administration Menu directory. The following menus are available in the Administration Menu directory: Status System , Video , Wireless (only for TV-IP600W camera) , Network and Active Users ....

TV-IP600/W Wireless Network Camera 32 Status The following menus are available in the Status: System , Video , Wireless (only for TV-IP600W camera) , Network and Active Users . To access a menu click the link of the item you want to view. System Status Click the System link from the column on the le...

TV-IP600/W Wireless Network Camera 33 Video Status Click the Video link from the column on the left hand-side to display the Video Status of your camera as shown on the screen below: Video Status display Video Status This section displays the video configuration of the camera, including the Video Re...

TV-IP600/W Wireless Network Camera 34 Wireless Status (for TV-IP600W only) Click the Wireless link from the column on the left hand-side to display the Wireless Status of your camera as shown on the screen below: Wireless Status display Wireless Status This section displays information about the Cam...

TV-IP600/W Wireless Network Camera 35 Network Status Click the Network link from the column on the left hand-side to display the Network Status of your camera as shown on the screen below: Network Status display Network Status This section displays information about the Camera’s LAN connection, incl...

TV-IP600/W Wireless Network Camera 36 Active Users Click the Active Users link from the column on the left hand-side to display the Active Users currently connected to your camera as shown on the screen below: Active Users display Active Users This section displays the IP address and Name of each us...

TV-IP600/W Wireless Network Camera 37 Configuration The following menus are available in the Configuration directory: System , Video , Wireless (only for TV-IP600W camera) , Network , User , Date/Time , Upload and E-mail . To access a menu click the link of the item that you want to view. System Con...

TV-IP600/W Wireless Network Camera 39 Video Settings Click the Video link from the column on the left hand-side to configure the image configuration of your camera. Video Settings menu Video Settings: Use this section to configure the video settings for your camera as described below: • Video Resolu...

TV-IP600/W Wireless Network Camera 41 Wireless Setup (for TV-IP600W only) The TV-IP600W Wireless Network Camera supports normal wireless LAN functions for 802.11b/g wireless networks including WEP or WPA basic security settings. Wireless Configuration menu

TV-IP600/W Wireless Network Camera 42 Wireless Interface Use the Wireless Interface menu to configure the Camera’s wireless interface. Wireless Interface menu • Connection Mode: Click a radio button to determine the type of wireless communication for the camera. The two options are Infrastructure an...

TV-IP600/W Wireless Network Camera 43 Encryption Use the Encryption menu to configure the Camera’s Encryption settings. Wireless Encryption menu • WEP Encryption: Wireless network communications can be intercepted easily. WEP (Wired Equivalent Privacy) is an encryption method specified by the IEEE 8...

TV-IP600/W Wireless Network Camera 45 Advanced Setting Use the Advanced Setting menu to configure the Camera’s advanced settings. Advanced Setting menu • Beacon Interval: Type a value to define the time interval between two beacons being sent. • Preamble: A preamble is a signal used in a wireless en...

TV-IP600/W Wireless Network Camera 46 Network Settings Click the Network Setup link to view menus for IP network settings, PPPoE configuration, DDNS, HTTP port configuration and UPnP configuration. Network Setup menus

TV-IP600/W Wireless Network Camera 47 TCP/IP • IP Address Mode: Click a radio button to define the IP Address Mode: Fixed IP You can select this option and enter the IP address directly. The default settings are: • IP Address – 192.168.10.30 • Subnet Mask – 255.255.255.0 • Default Gateway – 0.0.0.0 ...

TV-IP600/W Wireless Network Camera 48 User Use the User menus to add, edit and delete users for your camera. User menu User Access Control The Administrator has the authority to create additional users on the Camera and the privileges they have when accessing the Camera with the management software....

TV-IP600/W Wireless Network Camera 51 Upload Use the Upload menu to setup the configuration for the FTP Server, schedule FTP Server Uploads and configure manual FTP Server Uploads. Upload menu

TV-IP600/W Wireless Network Camera 53 Time Schedule Use this section to enable images to be uploaded to an FTP Server at regular intervals. Time Schedule menu • Enable upload image to FTP server: Tick the checkbox to enable images from the Camera to be uploaded to an FTP server. • Always: Click this...

TV-IP600/W Wireless Network Camera 56 E-mail Account Use this section to configure your E-mail Account configuration. E-mail Account settings • SMTP Server Address: SMTP (Simple Mail Transfer Protocol) is a protocol used for sending e-mail messages. Type in the mail server address that will be used ...

TV-IP600/W Wireless Network Camera 57 Time Schedule Use this section to section to enable images to be e-mailed to the specified e-mail account at regular intervals E-mail Time Schedule settings • Enable e-mail image to e-mail account server: Tick the checkbox to enable images from the Camera to be ...

TV-IP600/W Wireless Network Camera 58 Manual Operation Use this section to E-mail Manual Operation settings • Enable e-mail image to e-mail account: Tick the checkbox to enable images from the Camera to be e-mailed to an e-mail recipient. • Interval: Type a value in seconds to determine the time int...

TV-IP600/W Wireless Network Camera 59 Tools The following menus are available in the Tools directory: FTP Server Test , E-mail Test , Reset , Factory Reset, Firmware Upgrade and Backup . To access a menu click the link of the item you want to view. FTP Server Test Click the FTP Server Test item in t...

TV-IP600/W Wireless Network Camera 60 Reset This option allows you to restart your Camera. Reset menu Reset Device Clicking the Yes button will restart the Camera, retaining your saved settings, as if you were turning the device off and on. If you do not want to restart the Camera, exit this window ...

TV-IP600/W Wireless Network Camera 61 Firmware Upgrade When new firmware is available, you can upgrade it through this window. To upgrade the camera firmware, make sure the correct firmware file is located on your computer. Click the Browse button to locate the file. After locating the file, click t...

TV-IP600/W Wireless Network Camera 62 Backup The Backup window allows you to Backup or Restore the Camera settings. Backup Settings menu Backup Device Configuration to File To save configuration settings for the camera to a file on a local hard disk, click the Backup button. A prompt appears to conf...

TV-IP600/W Wireless Network Camera 63 Help The Help window displays help topics for the Camera. About The About option displays the Camera’s model name and version. About menu

TV-IP600/W Wireless Network Camera 64 Viewing Video The TV-IP600W allows you to view video images using ActiveX or Java in your web browser. Click View Video – Active X or Java from the Welcome screen to access the video images from your browser. Position your Camera for the desired location and tur...

TV-IP600/W Wireless Network Camera 65 Uploading/E-mailing Video In the View Video – Active X or Java windows, it is possible to turn the Upload Image and E-mail Image options ON of OFF . Simply click the corresponding ON or OFF buttons to turn the Upload Image or E-mail Image options ON or OFF . Upl...

TV-IP600/W Wireless Network Camera 66 Controlling the Camera You can control the Camera’s viewing angle using the control buttons on the left-hand side of the viewing window. Camera Control Buttons Adjusting the Viewing Angle To adjust the camera’s viewing angle, simply click the Up / Down / Left / ...

TV-IP600/W Wireless Network Camera 68 7 IPView Pro 2.0 This section describes the how to setup a camera using the IPView Pro 2.0 camera monitoring software. To install IPView Pro 2.0 on a system running Windows, launch the IPView Pro 2.0 installation software on the installation CD-ROM and follow th...

TV-IP600/W Wireless Network Camera 69 Add a camera for monitoring The Add camera menu is presented the first time the IPView Pro 2.0 software is launched. This menu is used to add cameras to the user interface for monitoring. After the first time running the software, this menu can be accessed at an...

TV-IP600/W Wireless Network Camera 71 IPView Pro 2.0 User Interface Below is a general description of the user interface. NO. Item Description 1 Live video display area Display area for single or multiple cameras of live video. Right click on any display area to view a list of quick configure option...

TV-IP600/W Wireless Network Camera 72 Display Controls The primary display and IPView Pro 2.0 control icons are described in detail below. When there are more than one camera displays viewed, one of the displays can be selected for management or additional changes. Simply left click on any display t...

TV-IP600/W Wireless Network Camera 73 Live video display controls Use the video display controls to change the view of the live video display. This is useful for multiple camera application. Click the arrows to manually cycle through the active camera’s live displays when using a single camera displ...

TV-IP600/W Wireless Network Camera 74 Camera configuration with IPView Pro 2.0 Access the camera configuration menus by clicking on the gear icon at the bottom of the right hand panel of the IPView Pro 2.0 user interface. Configuration options include adding and deleting cameras from the display vie...

TV-IP600/W Wireless Network Camera 75 2. Select the camera to add from the list, enter the administrator’s user name ( ID: ) and password, a preview of the live video display will appear. Click the OK, add this camera button, a confirmation message informs when the camera is connected and added to t...

TV-IP600/W Wireless Network Camera 76 Schedule Recording with IPView Pro 2.0 Use the Camera Settings menu to create schedules for recording and apply the schedules to any camera. Click the Camera Settings tab to view the Schedule Recording menu (the first menu viewed in the Camera Settings menu tab)...

TV-IP600/W Wireless Network Camera 77 Setup Motion Detection and Digital Input with IPView Pro 2.0 The Camera Settings menus include Motion Detection setup and Digital Input control. Each menu has the schedule option to apply a schedule for the action taken or always take the specified action. For M...

TV-IP600/W Wireless Network Camera 78 IPView Pro 2.0 Recording Options The Recording Options configured in the IPView Pro 2.0 help to conserve and manage allowed memory storage (disk space) and for video file management. Recorded files can be limited by time elapsed or by size. Use the select storag...

TV-IP600/W Wireless Network Camera 79 IPView Pro 2.0 Miscellaneous Options The Other Options available for configuration include Proxy server setup, email notification, scan interval and alert type settings.

TV-IP600/W Wireless Network Camera 80 8 Playing Video Files on a Computer IPCamPlayer software is installed on the monitoring station or administrator’s system along with the IPView Pro 2.0 monitoring software. Use it to playback and manage recorded video from the cameras added to the IPView Pro 2.0...

TV-IP600/W Wireless Network Camera 81 Load Saved Video Files Each camera has a file created automatically for storing video files. These files are normally located in the My Documents folder in Windows. The file folders are named according to the IP address and camera model. For example, 192.168.10....

TV-IP600/W Wireless Network Camera 82 To view recorded video files in the IPCamPlayer, it is first necessary to locate and select the files to be viewed and add them to the list. Click the Search Files button in the IPCamPlayer main interface and a new menu appears. In the new menu, use the Select C...

TV-IP600/W Wireless Network Camera 83 ffdshow The ffdshow software is used for audio and video encoding and decoding, especially for MPEG-4 formats. It is free software used on Windows systems and enables the user to tweak media playback and select specific codecs and formats. For use with the IPCam...

TV-IP600/W Wireless Network Camera 84 3. The InstallShield Wizard will appear, click Next in the welcome screen. 4. Accept the default location (Windows Programs folder) on the system for placement or Browse to choose an alternative, Click Next to continue.

TV-IP600/W Wireless Network Camera 85 5. Click to check the components that will be installed. For IPCamPlayer it is only necessary to use the default components already selected. Click Next to continue. 6. Accept the default destination folder (ffdshow) or Browse to choose an alternative, Click Nex...

TV-IP600/W Wireless Network Camera 86 7. Click to check the additional tasks that will be installed. For IPCamPlayer it is only necessary to use the default formats already selected. Click Next to continue. 8. Click to check the video applications that use ffdshow. For IPCamPlayer it is only necessa...

TV-IP600/W Wireless Network Camera 88 11. Review the information and click Install if satisfied that it is correct to install the necessary codecs. The installation will take a few seconds. 12. If desired, any of the three configuration utilities included with the ffdshow installation can be launche...

TV-IP600/W Wireless Network Camera 89 9 Appendix A. Frequently Asked Questions Internet Camera Features Q: What is an Internet Camera? A: An Internet Camera is a stand-alone system connecting directly to an Ethernet or Fast Ethernet network and supported by the wireless transmission based on the IEE...

TV-IP600/W Wireless Network Camera 90 Internet Camera Installation Q: Can the Internet Camera be used outdoors? A: The Camera is not water-proof and it is not recomended to use it outdoors. But you can use our Outdoor Internet Camera Enclosure TV-H500 or the one with Heater and Fan model TV-H510 to ...

TV-IP600/W Wireless Network Camera 91 B. PING your IP Address The PING (Packet Internet Groper) command can determine whether a specific IP address is accesible by sending a packet to the specific address and waiting for a reply. It can also be a useful tool in confirming whether an IP address confl...

TV-IP600/W Wireless Network Camera 92 4. Type ping x.x.x.x , where x.x.x.x is the IP address of the Camera, as shown below: Reply messages indicate that there is another device on the nework, as indicated in the above window.

TV-IP600/W Wireless Network Camera 93 C. Troubleshooting Q: I cannot access the Camera from a web browser? A1: The possible cause might by that the IP address of the Camera is already being used by another device. To correct the possible problem, you need to disconnect the Camera from the network fi...

TV-IP600/W Wireless Network Camera 94 A2.2: Click the Network Connections icon as shown below:

TV-IP600/W Wireless Network Camera 95 A2.3: Double-click the network adaptor that is connected to your Camera: Select TCP/IP from the “Network“ dialog box and from the TCP/IP Properties:

TV-IP600/W Wireless Network Camera 96 Click the Properities button. Double-click the Internet Protocol (TCP/IP) item and check that the first 3 bytes of your computer’s IP address correspond with the first 3 bytes of the Camera’s. If the Camera is situated on a different subnet than your workstation...

TV-IP600/W Wireless Network Camera 97 Q: Why does the Camera work locally but not externally? A1: The Camera’s connection might be being blocked by a Firewall. Please check with your System Administrator to see if your Firewall allows access to the Canera. A2: This could be caused by the Default Rou...

TV-IP600/W Wireless Network Camera 101 E. Adjusting Internet Camera Focus To adjust the focus of the lens, you need to turn the lens slowly in either a clockwise or anti-clockwise direction until the desired image appears. Be sure to not over turn the lens in either direction as this will cause the ...

TV-IP600/W Wireless Network Camera 102 G. Technical Specifications Camera   General    Sensor:   1/4”   color   CMOS   SOC   image   sensor   Resolution:   640   x   480   pixels   Board   Lens    Focal   Length:   4.57mm   F/No:   F1.9    Minimum   illumination:   1   Lux   @   F1.9   Focus   depth...

TV-IP600/W Wireless Network Camera 105 Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TV-IP600/TV-IP600W 3 years If a product does not operate as warranted above d...