TRENDNet TV-IP110W - Manuals

Page 2 - Table of Contents

Table of Contents English ...................................................................................................... 1 1 4 3 8 1. Before You Start2. Hardware Installation .........................................................................3. Configure the Internet Camera ..............

Page 3 - System Requirements; Package Contents; Before You Start; x 2dBi Detachable Antenna

System Requirements Package Contents 1. Before You Start English 1 ???? AC Power Adapter (5V, 2.5A) ? 1 x 2dBi Detachable Antenna ( ? TV-IP110/TV-IP110WQuick Installation Guide Utility CD-ROM TV-IP110W) 1.8m (5.9 ft) Cat.5 Fast Ethernet cable ? ? ? ? ? ? 10/100Mbps Ethernet CPU: Pentium 4 1GHz proce...

Page 4 - Application; Internet Camera Server; Wireless Internet Camera Server

Application English 2 Modem Internet Camera Server (TV-IP110) Cable/DSL 4-Port Broadband Router (TW100-S4W1CA) Notebook with PC Card (TE100-PCBUSR) Internet 10/100Mbps Wireless Internet Camera Server (TV-IP110W) Wireless G Firewall Router (TEW-432BRP) 54Mbps Modem Notebook with Wireless G PC Card (T...

Page 5 - Hardware Installation; Attach the; Antenna; and; Ethernet; port of the Internet

2. Hardware Installation English 3 1. Attach the Antenna . (TV-IP110W) 3. Connect the AC Power Adapter to the Internet Camera Server and then to a power outlet. 4. Verify the Power and Link LEDs are on. (TV-IP110W shown here) 2. Connect a RJ-45 network cable from a Switch/Router to the Ethernet port...

Page 6 - IP; Configure the Internet Camera; Go to; Installation Wizard; instructions and then click; Close

English 4 1. Insert the Utility CD-ROM into your CD-ROM drive and then click IP Setup . 3. Configure the Internet Camera Note: It is recommended that you configure the Internet Camera from a wired computer. Since the Internet Camera's default IP address is 192.168.10.30, make sure no other network d...

Page 7 - Click

English 5 6. Click OK and wait 30 seconds. 5. Configure the IP address to be in the same subnet as your network, type in the Administrator ID and Password and click Change . By default:ID: admin Password: admin 7. Click OK. 8. Double click the Internet Camera to access the browser configuration.

Page 9 - Disconnect the RJ-45 cable and; Your installation is now complete.; Register Your Product

English 7 13. Disconnect the RJ-45 cable and unplug the power. Then plug the power back in (TV-IP110W). 14. Verify the Power and Link LEDs are on. 15. Click Live View. Note: For detailed information regarding the TV-IP110/ 110W configuration and advanced settings, please refer to the Troubleshooting...

Page 10 - Troubleshooting

Q1: Q2: A2: Q3: A3: Q4: A4: Q5: A5: Q6: A6: The Image is blurry. How can I adjust the focus on the Internet camera? You can adjust the Internet Camera’s focus by rotating the lens. How do I configure TCP/IP settings on my computer? When I click on Live View the image does not load? First, make sure ...

Page 11 - Certifications

Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference.(2) This device must accept any interference received. Including interference that may cause undesired oper...

Page 12 - US Canada; Worldwide

Copyright ©2007. All Rights Reserved. TRENDnet. 20675 Manhattan PlaceTorrance, CA 90501USA Product Warranty Registration Please take a moment to register your product online. Go to TRENDnet’s website at http://www.trendnet.com/register TRENDnet Technical Suppor t US Canada 24/7 Tech Support Toll Fre...