TP-Link TL-SF1024 - Manuals

TP-Link TL-SF1024 Switch – Manual in PDF format online.

Manuals:

Manual

Manual TP-Link TL-SF1024

Summary

Page 2 - COPYRIGHT & TRADEMARKS; Specifications are subject to change without notice.; FCC STATEMENT; This device may not cause harmful interference.; CE Mark Warning

I COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used...

Page 3 - Related Document

II Related Document This Installation Guide is also available in PDF on our website. To obtain the latest documentation and prodcut information, please visit our official website: http://www.tp-link.com About this Installation Guide This Installation Guide describes the hardware characteristics, ins...

Page 5 - Product Overview; duplex mode; ACCearance; Front Panel; The front panel of The TL-SF1016 is shown as the following figure.; The front panel of The TL-SF1016DS is shown as the following figure.

01 10/100Mbps Fast Ethernet Switch Introduction ChaCter C Product Overview C1C TL-SF1016/TL-SF1016DS/TL-SF1024/TL-SF1024D/TL-SF1048 switch provides 16/24/48 10/100Mbps Auto-Negotiation RJ45 ports. Each port of the TL-SF1016/TL-SF1016DS/ TL-SF1024/TL-SF1024D/TL-SF1048 supports auto MDI/MDI-X function...

Page 6 - The front panel of The TL-SF1024 is shown as the following figure.; The front panel of The TL-SF1024D is shown as the following figure.; The front panel of The TL-SF1048 is shown as the following figure.; A device is linked to the corresponding port

02 10/100Mbps Fast Ethernet Switch LEDs 10/100Mbps RJ45 Port Front Panel of TL-SF1016DS Figure 1-2 The front panel of The TL-SF1024 is shown as the following figure. LEDs 10/100Mbps RJ45 Port Front Panel of TL-SF1024 Figure 1-3 The front panel of The TL-SF1024D is shown as the following figure. LEDs...

Page 7 - The rear panel of the switch is shown as the following figure.; Grounding Terminal; Chapter 3 Lightning Protection; Power Socket; Please use the provided power cord.

03 10/100Mbps Fast Ethernet Switch 10/100Mbps Por t Designed to connect to the device with a bandwidth of 10Mbps or 100Mbps. Each has a corresponding 10/100Mbps LED. Rear Panel ■ The rear panel of the switch is shown as the following figure. Grounding Terminal Power Socket Rear Panel Figure 1-6 Grou...

Page 8 - Package Contents; Safety Precautions

04 10/100Mbps Fast Ethernet Switch Installation ChaCter 1 Package Contents 11C Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor. One Switch One Power Cord This Installation Guide Safety Precautions 111 To avoid...

Page 9 - Site Requirements; Clearness; Dust the device regularly, and keep the indoor air clean.; Electromagnetic Interference; transmitting station.

05 10/100Mbps Fast Ethernet Switch Site Requirements ■ Temperature/Humidity ȭ ȭ Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity leakage, mechanical property changes and corrosions. Too high temperature may accelerate ...

Page 10 - Lightening Protection; C hapte r 3; Installation Site; Installation Tools

06 10/100Mbps Fast Ethernet Switch Lightening Protection Extremely high voltage currents can be produced instantly when lightning occurs and the air in the electric discharge path can be instantly heated up to 20,000 ℃ . As this instant current is strong enough to damage electronic devices, more eff...

Page 11 - Product Installation; Rack Installation

07 10/100Mbps Fast Ethernet Switch Note: These tools are not provided with our product. If needed, please self purchase them. Product Installation 112 Desktop Installation ■ To install the device on the desktop, please follow the steps: Set the device on a flat surface strong enough to support the e...

Page 12 - Please set 5~10cm gaps around the device for air circulation.

08 10/100Mbps Fast Ethernet Switch After the brackets are attached to the device, use suitable screws (not provided1 to 3. secure the brackets to the rack, as illustrated in the following figure. Rack Rack Installation Figure 2-3 Caution: Please set 5~10cm gaps around the device for air circulation....

Page 13 - Cabling Reasonably; please use a signal lightning arrester.; Requirements for Cabling Outdoors; Aerial cabling without safeguard is not allowed.

09 10/100Mbps Fast Ethernet Switch Lightning Protection ChaCter 1 Cabling Reasonably 11C In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced lig...

Page 14 - Requirements for Cabling Indoors; devices are in following tables.

10 10/100Mbps Fast Ethernet Switch Requirements for Cabling Indoors ■ When cabling indoors, keep a certain distance away from the devices that may cause high-frequenc y inter ferences, such as down-conduc tor cable, powerline, power transformer and electromotor. The main cable should be paved in the...

Page 15 - Connect to Ground

11 10/100Mbps Fast Ethernet Switch 2~5kVA powerline Parallel cabling 300 One is in the grounded metal raceway or metal pipe 150 The both are in the grounded metal raceway or metal pipe 80 >5kVA powerline Parallel cabling 600 One is in the grounded metal raceway or metal pipe 300 The both are in t...

Page 16 - Connecting to the Ground via the Power Supply; EquiCotential Bonding

12 10/100Mbps Fast Ethernet Switch Note: The grounding bar and the ground cable are not provided with our product. If needed, please self purchase them. Connecting to the Ground via the Power Supply ■ If the device is installed in the normal environment, the device can be grounded via the PE (Protec...

Page 17 - at least. The shorter cable the bet ter, and use a; Use Lightning Arrester

13 10/100Mbps Fast Ethernet Switch Grounding Terminal Equipotential Bonding CableGrounding Bar Ground Cable Equipotential Bonding Figure 3-3 When equipotential bonding, please note that the cable should be copper wrapped Kelly with its area being 6mm 2 at least. The shorter cable the bet ter, and us...

Page 19 - Ethernet Port; Verify Installation; the air flow is adequate.; Power On

15 10/100Mbps Fast Ethernet Switch Connection ChaCter 2 Ethernet Port 21C Connect the Ethernet ports of the switch to the network devices by RJ45 cable as the following figure shown. RJ45 Port RJ45 Cable Connecting the Ethernet Port Figure 4-1 Verify Installation 211 After completing the installatio...

Page 20 - Initialization; resetting of the system.; ACCendix A Troubleshooting; The Power LED is not lit; Make sure the AC power cord connected the switch with power source; The Link/Act LED is not lit when a device is connected to the; QQQQ; corresConding Cort; You are recommended to check the following items:

16 10/100Mbps Fast Ethernet Switch Note: The figure is to illustrate the application and principle. The power plug you get from the package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above. Initialization 212 After the device ...

Page 21 - ACCendix B Hardware SCecifications

17 10/100Mbps Fast Ethernet Switch ACCendix B Hardware SCecifications Item Content Standards IEEE 802.3 10Base-T IEEE 802.3u 100Base-TX IEEE 802.3x Flow Control Transmission Medium 10Base-T: UTP/STP of Cat. 3 or above(maximum 100m1 100Base-TX: UTP/STP of Cat. 5 or above(maximum 100m1 Safety & Em...

Page 22 - ACCendix C Technical SuCCort

18 10/100Mbps Fast Ethernet Switch ACCendix C Technical SuCCort For more help, please go to: http://www.tp-link.com/en/support/faq ■ To download the latest Firmware, Driver, Utility and User Guide, please go to: ■ http://www.tp-link.com/en/support/downloadFor all other technical support, please cont...