Toshiba Satellite M30X - Manuals

Table of Contents Chapter 1 Hardware Overview 1.1 Features ............................................................................................................................ 1-1 1.2 System Unit....................................................................................................

Chapter 3 Tests and Diagnostics 3.1 The Diagnostic Test .........................................................................................................3-1 3.2 Executing the Diagnostic Test..........................................................................................3-2 3.3 Conf...

Chapter 4 Replacement Procedures 4.1 General ............................................................................................................................. 4-1 4.2 Battery.....................................................................................................................

x Satellite M30X Maintenance Manual Appendices Appendix A Handling the LCD Module .................................................................................. A-1 Appendix B Board Layout ....................................................................................................... B-1...

1 Hardware Overview 1-ii Satellite M30X Series Maintenance Manual

1 Hardware Overview Chapter 1 Contents 1.1 Features ...................................................................................................................... 1-1 1.2 System Unit.................................................................................................................

1 Hardware Overview 1.1 Features • ENE CB1410 and CB714 can be co-layout. PC Card 95 supported with one type II Card sockets • PCI card bus • NO ZV-Port support • With dummy card for PCMCIA • 5 in 1 reader, BTO (Rubber cap ) (Support XD, SD, SM, MS, MS Pro and MMC) • No SD-IO support ‰ Universal Ser...

1 Hardware Overview 1.2 System Unit 1.2 System Unit The system unit is composed of the following major components: ‰ Processor • Intel Pentium M Dothan :1.5G/1.6G/1.7G/1.8G/2G/2.1G/1.4G(Trailing CMT 85Tj, TDP=21W) • Intel Pentium M Banias 1.5G/1.6G/1.7G • Intel Celeron M Banias 1.3G/1.4G/1.5G • Inte...

1 Hardware Overview 1.5 Power Supply 1.4 Optical device Drives • CD-RW/DVD-ROM drive • DVD+-R/+-RW drive • DVD Super Multi ddrive 1.5 Power Supply The power supply supplies seven different voltages to the system board and performs the following functions: 1. A/D conversion The EC uses 10-bit samplin...

1 Hardware Overview 1.6 Batteries 1.6 Batteries The computer has two types of battery: ‰ Main battery pack (18650 size) ‰ RTC battery The removable main battery pack is the computer’s main power source when the AC adaptor is not attached. The battery specifications are listed in the table below. Bat...

1.6 Batteries 1 Hardware Overview NOTES 1. The time required for normal charge is affected by the amount of power the system is consuming. Use of the fluorescent lamp and frequent disk access diverts power and lengthens the charge time. 2. Using quick charge, the power supply microprocessor automati...

2 Troubleshooting Procedures 2-ii Satellite M30X Series Maintenance Manual

2 Troubleshooting Procedures Chapter 2 Contents 2.1 Troubleshooting Introduction .................................................................................... 2-1 2.2 Troubleshooting Flowchart ........................................................................................ 2-2 2.3 Pow...

2 Troubleshooting Procedures Figures Figure 2-1 Troubleshooting flowchart (1/2) ....................................................................2-3 Figure 2-1 Troubleshooting flowchart (2/2) ....................................................................2-4 Figure 2-2 Power Supply Troublesh...

2.1 Troubleshooting Introduction 2 Troubleshooting Procedures 2.1 Troubleshooting Introduction Chapter 2 describes how to determine if a Field Replaceable Unit (FRU) in the computer is causing the computer to malfunction. The FRUs covered are: 1. Display 6. Printer (parallel) port 11. PCMCIA unit 2....

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2.2 Troubleshooting Flowchart If you know the location of the malfunction, turn directly to the appropriate section of this chapter. If the problem is unspecified, use the flowchart in Figure 2-1 as a guide for determining which troublesh...

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting S T A R T A r e th e D C -I N a n d B a tte r y L E D s lit? C a n y o u tu r n th e c o m p u te r o n ? A r e th e in te r n a l p o w e r c o n n e c tio n s s e c u r e ? E N D C h e c k P o w e r S u ...

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting The power supply controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed. The flowchart in Figure 2-2 gives a summary of...

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Table 2-2 DC-IN LED AC-IN LED Power supply status Solid on AC power exists (LED is solid green). Off No AC power exists. To check the power supply status, install a battery pack and connect an AC adaptor to the DC-IN port on the computer ...

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting Procedure 3 Power supply connection check The power supply wiring diagram is shown below: AC adaptor System board Battery AC adaptor cord AC power cord Any of the connectors may be disconnected. Perform Check 1. Check 1 Disconnect the AC ...

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Procedure 4 Diagnostic check The power supply may not charge the battery pack. Perform the following procedures: 1. Reinstall the battery pack. 2. Attach the AC adaptor and turn on the power. If you cannot turn on the power, go to Procedu...

2 Troubleshooting Procedures 2.4 Display Troubleshooting 2.4 Display Troubleshooting P e r f o r m e x t e r n a l d i s p l a y c h e c k ( P r o c e d u r e 1 ) S T A R T D o e s t h e e x t e r n a l d i s p l a y f u n c t i o n o k ? P e r f o r m d i a g n o s t i c c h e c k ( P r o c e d u r...

2.4 Display Troubleshooting 2 Troubleshooting Procedures This section describes how to determine if the computer’s display is functioning properly. The process is outlined in Figure 2-3. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: External display check ...

2 Troubleshooting Procedures 2.4 Display Troubleshooting Procedure 3 Connector and replacement check The FL inverter board, LCD module, and system board are connected to the display circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, for instructions on how ...

2.5 Keyboard Troubleshooting 2 Troubleshooting Procedures 2.5 Keyboard Troubleshooting P e r f o r m e x t e r n a l k e y b o a r d c h e c k ( P r o c e d u r e 1 ) S T A R T D o e s t h e e x t e r n a l k e y b o a r d f u n c t i o n o k ? P e r f o r m d i a g n o s t i c c h e c k ( P r o c e...

2.6 External USB Devices Troubleshooting 2 Troubleshooting Procedures 2.6 External USB Devices Troubleshooting R e p l a c e s y s t e m b o a r d ( P r o c e d u r e 2 ) E N D O r i g i n a l U S B d e v i c e i s f a u l t y P e r f o r m e x t e r n a l d e v i c e a n d c o n n e c t i o n c h e...

2 Troubleshooting Procedures 2.6 External USB Devices Troubleshooting To determine if the computer’s external USB devices are functioning properly, perform the following procedures. Figure 2-6 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: External device and c...

2.7 TV-Out Failure Troubleshooting 2 Troubleshooting Procedures 2.7 TV-Out Failure Troubleshooting P e r f o r m T V c o n n e c t i o n c h e c k ( P r o c e d u r e 1 ) S T A R T D o e s r e p l a c e m e n t T V c a b l e f u n c t i o n p r o p e r l y ? P e r f o r m T V s e t c h e c k ( P r o...

2.8 Printer Port Troubleshooting 2 Troubleshooting Procedures 2.8 Printer Port Troubleshooting START Perform diagnostic check (Procedure 1) Does the print port function ok? Perform print port loopback check (Procedure 2) Print port is not faulty continue troubleshooting refer to Figure 2.1 Was a pri...

2.9 Touch Pad Troubleshooting 2 Troubleshooting Procedures 2.9 TouchPad Troubleshooting START END TouchPad connection check (Procedure 1) TouchPad replacement check (Procedure 2) Replace system board Figure 2-8 TouchPad troubleshooting process Satellite M30X Series Maintenance Manual 2-23

2.10 Speaker Troubleshooting 2 Troubleshooting Procedures 2.10 Speaker Troubleshooting START Do all sources have same problem? END Perform earphone test (Procedure 2) Do earphones function correctly? Perform connection check (Procedure 3) Perform replacement check (Procedure 4) Perform audio source ...

2.11 Optical Drive Troubleshooting 2 Troubleshooting Procedures 2.11 Optical Drive Troubleshooting START Audio CD functions ok? END Perform software check (Procedure 3) Perform diagnostic test (Procedure 4) Perform connection and replacement check (Procedure 5) Perform audio CD check (Procedure 1) P...

2 Troubleshooting Procedures 2.12 Modem Troubleshooting 2.12 Modem Troubleshooting START Computer unable to detect telephone signal? END Perform connection check (Procedure 2) Perform replacement check (Procedure 3) Perform telephone line connection check (Procedure 1) Check / replace telephone line...

2 Troubleshooting Procedures 2.13 PCMCIA Troubleshooting 2.13 PCMCIA Troubleshooting START Do errors occur during SYCARD test? Perform PCMCIA socket replacement check (Procedure 2) Replace system board END PCMCIA unit is not faulty. Perform SYCARD test (Procedure 1) No Yes Figure 2-12 PCMCIA trouble...

2 Troubleshooting Procedures 2.15 Wireless LAN Troubleshooting 2.15 Wireless LAN Troubleshooting START Perform diagnostic test (Procedure 1) Was a wireless LAN problem delected? Perform connector and replacement check (Procedure 2) Replace wireless LAN antenna/unit Replace system board END Yes Wirel...

3. Tests and Diagnostics 3-ii Satellite M30X Series Maintenance Manual

Test and Diagnostic Operation Contents 3.1 The Diagnostic Test ......................................................................................................... 3-1 3.2 Executing the Diagnostic Test ......................................................................................... 3-2...

3.1 The Diagnostic Test 3. Tests and Diagnostics 3.1 The Diagnostic Test This chapter explains how to use the Test & Diagnostic program to test the functions of the computer’s hardware modules. The Test & Diagnostic Program is stored on the T&D diskettes. The program consists of a series...

3. Tests and Diagnostics 3.2 Executing the Diagnostic Test 3.2 Executing the Diagnostic Test Toshiba MS-DOS is required to run the DIAGNOSTICS PROGRAM. To start the DIAGNOSTIC PROGRAM, follow these steps: 1. Insert the diagnostics diskette #1 in the floppy disk drive and turn on the computer. (The d...

3. Tests and Diagnostics 3.3 Config Check Test 3.3 Config Check Test The config check test checks unit configuration. It includes: Š CPU type Š System memory size Š ODD type Š HDD type & capacity Š BIOS version This test needs input unit Part Number by manual to make comparison with known SKU da...

3. Tests and Diagnostics 3.5 PIO Loopback Test 3.5 PIO Loopback Test The PIO loopback test will check below items through PIO loopback connector. Š External Interrupt Š External Loopback - including Pattern test, Data Pin test, Control register test & Control pin/ Status pin test. NOTE : Remembe...

3. Tests and Diagnostics 3.7 Speaker Audio Test 3.6 Speaker Audio Test The speaker audio test allows the user to aurally confirm the speaker functions. And check both speakers if they are OK within 3 times “Beep” sound generated. NOTE : Remember to tune up the volume as “ Maximum ” before this test ...

3. Tests and Diagnostics 3.9 Main Battery Change Test 3.8 Main Battery Charge Test NOTE : The AC adaptor ( 120W/90W, 19V ) should be connected to successfully run this test. This test shows and measures the main battery: Š Battery type (Ni-MH / Lion) Š Manufacturer (Sony / Sanyo) Š Remain charge cap...

3.10 FDD Test 3. Tests and Diagnostics 3.9 FDD Test NOTE : Before running the FDD test, prepare a formatted work diskette (1.44 MB). Remove the diagnostics diskette and insert the work diskette into the FDD. The contents of the floppy diskette maybe erased. The Floppy Disk Test includes three subtes...

3. Tests and Diagnostics 3.12 Keyboard Test Pressing a key also reveals that key’s scan codes in the upper right hand corner of the screen. When the key is depressed, its make code is displayed. When the key is released, the break code is shown. 3-16 Satellite M30X Series Maintenance Manual

3.14 LCD Pixels Mode Test 3. Tests and Diagnostics 3.13 LCD Pixels Mode Test This LCD pixels mode test checks whether video display is fine. This test includes two modes of the test: 1. Text Mode - including 40*25 (16 colors) and 80*25 (2/16colors). 2. VGA Mode - including 320*200 (4/16/256 colors),...

3. Tests and Diagnostics 3.15 Lid Switch Test 3.14 Lid Switch Test The lid switch test checks the lid function of the unit. When LCD cover closed, the lid should enable to turn off the display. NOTE : Remember to tune up the volume as “ Maximum ” before this test starts. Follow below steps to run th...

3.16 HDD R/W Test 3. Tests and Diagnostics 3.15 HDD R/W Test The HDD R/W test allows the user to test aurally HDD read/write function. For data security concern, it is necessary to input password - “ TOSHIBA ” before HDD write test starts. The HDD test includes three subtests of the: 1. Sequential r...

3. Tests and Diagnostics 3.19 CD Control Button Test 3.18 CD Control Button Test The CD control button test allows the user to manually test each of the five CD control buttons. The figure below will be displayed: Press each of the buttons on the front panel in turn. A yellow bar will appear on the ...

4 Replacement Procedures 4-ii Satellite M30X Series Maintenance Manual

4 Replacement Procedures Chapter 4 Contents 4.1 General ............................................................................................................................. 4-1 4.2 Battery..........................................................................................................

4 Replacement Procedures Safety Precautions Before you begin disassembly, read the following safety precautions and observe them carefully as you work. DANGER: 1. Always use the lithium ion battery pack or backup battery that is authorized by Toshiba or compatible with the unit. Since other battery ...

4 Replacement Procedures Before You Begin Look over the procedures in this section before you begin disassembling the computer. Familiarize yourself with the disassembly and reassembly steps. Begin each procedure by removing the AC adaptor and the battery pack as instructed in section 4.2. 1. Do not...

4 Replacement Procedures Disassembly Procedures The computer has two basic types of cable connectors: ‰ Pressure Plate Connectors ‰ Standard Pin Connectors To disconnect a Pressure Plate connector, lift up the tabs on either side of the connector’s plastic pressure plate and slide the cable out of t...

4 Replacement Procedures Tools and Equipment The use of Electrostatic Discharge (ESD) equipment is very important for your safety and the safety of those around you. Proper use of these devices will increase the success rate of your repairs and lower the cost for damaged or destroyed parts. The foll...

4 Replacement Procedures 4.2 Battery Removing the Battery Pack To remove the battery pack from the battery bay, follow the steps below. 1. Turn the computer upside down. 2. Unlock the battery double lock and slide the battery bay latch to release the battery pack. Then you can remove it from the bay...

4 Replacement Procedures Installing the Battery Pack To install the battery pack in the battery bay, follow the steps below and refer to the figure in the preceding section. WARNING: The battery is a lithium ion battery and can explode if not properly replaced, used, handled or disposed of. Use only...

4 Replacement Procedures 4.3 PC Card Removing a PC Card To remove a PC Card, follow the steps below. 1. Push the PC Card’s eject button. The button pops out when you release it. 2. Push the eject button once more to pop the PC Card out slightly. 3. Grasp the PC Card and remove it. 4. Push the eject ...

4 Replacement Procedures Installing the PC Card To install the PC Card, follow the steps below and refer to the figures in the preceding section. 1. Make sure the eject button does not stick out. 2. Insert the PC Card and press gently to ensure a firm connection. Figure 4-3 Installing the PC card 4-...

4 Replacement Procedures 4.4 HDD CAUTION : When handling the HDD, do not press the top surface as shown by the arrow. Hold it by the sides. Figure 4-4 HDD Removing the HDD Module Follow the steps below to remove HDD module: 1. 2. 3. Turn the computer upside down Remove a black M2.5x5 screw to releas...

4 Replacement Procedures 4. 5. Remove the two M3x3 black screws that secure the HDD case and bracket to the HDD. Remove the HDD from the HDD case. Installing the HDD To install the HDD, follow the steps below and refer to the figures in the preceding section. 1. Seat the HDD in the HDD case and brac...

4 Replacement Procedures 4.5 Optical Drive Module Removing the Optical Drive Module To remove the optical drive module, you need to remove the keyboard first. Follow the steps below: 1. Turn the computer upside down. 2. Remove the screw M2.5x5 securing the optical drive module 3. Use your hand to pu...

4 Replacement Procedures Installing the Optical Drive Module To install a device in the optical drive module bay, follow the steps below and refer to the figure in the preceding section. 1. Slide the device into the optical drive module bay. 2. Use the screw M2.5x5 to secure the optical drive module...

4 Replacement Procedures 4.6 Optical Drive This computer may be fitted with a: CD-RW/DVD-ROM device DVD-ROM device DVD-R/-RW device DVD+-R/+-RW DVD Super Multi device Disassembling the Optical Drive To disassemble the optical drive, first remove the drive from its module bay, then follow the steps b...

4 Replacement Procedures Reassembling the Optical Drive To reassemble an optical drive, follow the steps below and refer to the figure in the preceding section. 1. Position the optical drive bracket plate to the rear panel of optical drive. 2. Secure the optical drive bracket plate with two black M2...

4 Replacement Procedures 4.7 Wireless LAN Unit Removing the Wireless LAN Unit To remove wireless LAN unit, you must remove strip cover and keyboard first, then follow the steps below to remove wireless LAN unit. 1. Remove the embedded screw securing the wireless LAN door, and then remove the wireles...

4 Replacement Procedures Installing the Wireless LAN Unit To install the wireless LAN unit, follow the steps below and refer to the figures in the preceding section. 1. Remove strip cover and keyboard. 2. Remove the embedded screw securing the wireless LAN door, and then remove the wireless LAN door...

4 Replacement Procedures 4.8 Expansion Memory Removing the Expansion Memory To remove the memory module, make sure the computer is in boot mode then: 1. Be sure the power is off and all cables are disconnected from the computer. 2. Turn the computer upside down and remove the battery and the screw s...

4 Replacement Procedures Installing the Expansion Memory CAUTION : Do not touch the connectors on the expansion memory or on the computer. Debris on the connectors may cause memory access problems. Follow these steps to install a memory module: 1. Set the computer to boot mode and turn off the power...

4 Replacement Procedures 4.9 Keyboard Removing the Keyboard Follow the steps below to remove the keyboard: 1. Open the display panel. 2. Insert a thin tool into the gap between the strip cover and keyboard to lever the strip cover up and then release the strip cover. Figure 4-13 Removing the strip c...

4 Replacement Procedures Figure 4-15 Disconnecting the keyboard cable Installing the Keyboard To install the keyboard, follow the steps below and refer to the figures in the preceding section. 1. Connect the keyboard cable to the system board. 2. Set the keyboard in place and secure it with two M2 x...

4 Replacement Procedures 4.10 Modem Removing the Modem To remove the installed modem, first remove the strip cover and keyboard, then follow the steps below: 1. Remove the embedded screw to release the modem cover. 2. Remove two M2.5x5 screws securing the modem module. 3. Carefully lift the unit off...

4 Replacement Procedures Installing the Modem To install a modem, follow the steps below and refer to the figures in the preceding section. 1. Connect the modem cable to the modem module. 2. Fit the modem onto its connector and secure it with two black M2.5x5 screws. 3. Replace the keyboard and stri...

4 Replacement Procedures 4.11 Display Assembly Removing the Display Assembly To remove the display assembly, first remove the keyboard and wireless LAN, then follow the steps below: 1. Remove the strip cover and then remove the two black screws M2x2 securing the keyboard. 2. Disconnect the wireless ...

4 Replacement Procedures 3. Disconnect the LCD power cable from the top chassis. LCD Cable Figure 4-18 Disconnecting the LCD cable 4. Remove two M2.5x8 screws securing LCD from the back side. 5. Remove two M2.5x8 screws securing LCD to the top cover. M2.5X8 Figure 4-19 Removing the display assembly ...

4 Replacement Procedures Installing the Display Assembly To install the display assembly, follow the steps below and refer to the figures in the preceding section. 1. Seat the display assembly taking care not to crush to the LCD display cable, the LCD power cable, or wireless LAN antenna. 2. Secure ...

4 Replacement Procedures 4.12 Top Cover Removing the Cover To remove the top cover, first remove the battery pack, display assembly, optical drive module, HDD, and memory module and wireless LAN as described in the preceding sections, then follow the steps below: 1. Remove modem and wireless LAN cov...

4 Replacement Procedures Installing the Top Cover To install the top cover, follow the steps below and refer to the figures in the preceding section. 1. Seat the top cover and secure the upper FFC cable and Touch pad FFC cable to the computer’s top chassis. 2. Secure the top cover with one M2.5x10 s...

4 Replacement Procedures 4.13 Touch Pad Removing the Cover To remove the Touch Pad, first remove the top cover, then follow the steps below: 1. Disconnect the Touch Pad FFC cable from the Touch Pad. 2. Remove one M2.5x3 screw securing the Track Pad Bracket. Slide it and Lift out the Track Pad Bracke...

4 Replacement Procedures Installing the Touch Pad To install the Touch Pad, follow the steps below and refer to the figures in the preceding section: 1. With the top cover upside down, place the Touch Pad, the Track Pad Bracket, and LED PCB board in position. 2. Secure the LED PCB board with two M2....

4 Replacement Procedures 4.14 Speakers Removing the Speakers To remove the speakers, first remove the top cover, then follow the steps below: 1. Remove the two M2.5x5 screws and then disconnect the speaker cable from the speakers. Figure 4-23 Removing the speakers 2. Lift out the speakers. 4-36 Sate...

4 Replacement Procedures Installing the Speakers To install the speakers, follow the steps below and refer to the figure in the preceding section: 1. Seat each speaker. 2. Secure each speaker with M2.5x5 screw. 3. Attached the speaker cable to the system board. 4. Reassemble the rest of the computer...

4 Replacement Procedures 4.15 System Board Removing the System Board To remove the system board, first remove the LCD assembly, top cover and HDD, then follow the steps below: 1. Remove the thermal plate and audio FCC cable. 2. Remove four thermal screws to release thermal module. 3. Remove the ther...

4 Replacement Procedures Installing the System Board To install the system board, follow the steps below and refer to the figures in the preceding section. 1. Seat the system board in the chassis. 2. Connect the thermal cable. 3. Replace the thermal module and secure it with four thermal screws. 4. ...

4 Replacement Procedures 4.16 Fan & CPU Removing the Fan & CPU To remove the Fan, Heat Sink, and CPU, you must first remove the panel, keyboard, top cover and bottom chassis to reveal the system board, then follow the steps below: 1. Turn the system board upside down and remove the four embe...

4 Replacement Procedures Installing the CPU To install the CPU, follow the steps below and refer to the figures in the preceding section. CAUTION: If you remove the heat sink, you should use the CPU grease tool to remove the grease on the CPU and heat sink. Reapply fresh grease before installing the...

4 Replacement Procedures 4.17 Display Mask Removing the Display Mask To remove the display mask, first remove the display assembly as described earlier, then follow the steps below: 1. Remove the mask seals to expose two lower inner corner screws securing the display mask. 2. Remove two M2.5 × 5 bla...

4 Replacement Procedures Installing the Display Mask To install the display mask, follow the steps below and refer to the figures in the preceding section. 1. Seat the display mask and secure the snaps on each side. 2. Secure the display mask with two M2.5x5 screws at the bottom inner corner. 3. Cov...

4 Replacement Procedures 4.18 LCD Module Removing the LCD Module To remove the LCD module, first remove the display assembly and display mask, then follow the steps below. 1. Remove two M2x3 black screws securing the LCD cable and FL inverter board. 2. Disconnect the LCD cable from the FL inverter b...

4 Replacement Procedures 4. Remove six M2x3 screws securing LCD module bracket to LCD module. Remove LCD cable. LCD cable M2X3 M2X3 M2.5X5 M2X3 FL inverter board Figure 4-30 Removing the LCD module-2 5. Remove the LCD module. NOTE : If the LCD module malfunctions, remove the LCD cable and LCD bracke...

4 Replacement Procedures Installing the LCD Module To install the LCD module, follow the steps below and refer to the figures in the preceding section. 1. Set the LCD module in the display assembly. 2. Connect the FL cable and the HV cable to the FL inverter board. 3. Seat the LCD module in the disp...

4 Replacement Procedures 4-48 Satellite M30X Series Maintenance Manual 4.19 FL Inverter Board Removing the FL Inverter Board To remove the FL inverter board, first remove the battery pack, the display assembly, display mask, and LCD module, then follow the steps below. 1. Remove one M2x3 black screw...

Appendix Contents Appendix A Handling the LCD Module............................................................................... A-1 Appendix B Board Layout..................................................................................................... B-1 B.1 System Board (FRDSY*) Bottom Vi...

Satellite M30X Series Maintenance Manual App-v Tables Table B-1 System board ICs (top and bottom) .................................................................... B-3 Table B-2 System board connectors (top and bottom) ........................................................ B-4 Table C-1 SODIMM ...

Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Therefore, please observe the following precautions when handling it: 1. When installing the LCD module in the LCD cover, be sure to seat it so t...

Appendix B Appendix B Board Layout B.1 System Board (FRDSY*) Bottom View N L I H G F D C B JP24 Figure B-1 System board (FRDSY*) layout (Bottom) Satellite M30X Series Maintenance Manual B-1

Table B-2 System board connectors (top and bottom) Number Name JP1 Parallel Connector JP2 CRT Connector JP3 TV-OUT Connector JP4 RJ11/RJ45 Connector JP5, JP21 USB Connector JP6 LVDS Connector JP7 FAN Connector JP8 HDD Connector JP10 MINI PCI JP11 ODD Connector JP12 CARDBUS Socket JP13 5-IN-1 Cardrea...

Satellite M30X Series Maintenance Manual B-5 PJP2 Battery Connector

C. Appendix C Pin Assignments System Board C.1 JP24 Table C-1 SODIMM I/F pin assignments (200-PIN) (1/4) Pin No. Signal name I/O Pin No. Signal Name I/O 1 VREF O 2 VREF O 3 VSS - 4 VSS - 5 DDR_DQ0 I/O 6 DDR_DQ2 I/O 7 DDR_DQ3 I/O 8 DDR_DQ7 I/O 9 +2.5V O 10 +2.5V O 11 DDR_DQS0 I/O 12 DDR_DM0 O 13 DDR_...

Appendix D Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! 02 82 16 F0 16 03 2 @ 03 83 1E F0 1E 04 3 # 04 84 26 F0 26 05 4 $ 05 85 25 F0 25 06 5 % 06 86 2E F0 2E 07 6 ^ ...

Table D-1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 X Fn — — — — *4 X Win E0 5B E0 DB E0 1F E0 F0 1F x App E0 5D E0 DD E0 2F E0 F0 2F Notes...

Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 55 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 75 INS E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12 76 DEL E0 AA E0 53 E0 D3 E0 2A E0 F0 12 E0 71 E0 F0 71 E0 12 79 ← E0 AA E0 4B E...

Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Break Make Break 75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 76 DEL E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12 79 ← E0 2A E0 4B E0 CB E0 AA E0 12 E0 6B E0 F0 6B E0 F0 12 80 Home E0 2A E0 47 E0...

Table D-5 Scan codes in overlay mode Code set 1 Code set 2 Cap No. Keytop Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F0 74 26 P (–) 4A CA 7B F0 7B 37 J (1) 4F CF 69 F0 69 38 K (2) 50 ...

Appendix E Appendix E Key Layout E.1 United States (US) Keyboard Figure E-1 US keyboard E.2 United Kingdom (UK) Keyboard Figure E-2 UK keyboard Satellite M30X Series Maintenance Manual E-1

E.3 Spanish (SP) Keyboard Figure E-3 SP keyboard E.4 Japanese (JA) Keyboard Figure E-4 JA keyboard E-2 Satellite M30X Series Maintenance Manual

E.11 Chinese (CH) Keyboard Figure E-11 CH keyboard E.12 Swissc-Darfon Keyboard Figure E-12 Swissc-Darfon keyboard E-6 Satellite M30X Series Maintenance Manual

E.13 IT new Keyboard Figure E-13 IT new keyboard Satellite M30X Series Maintenance Manual E-7

F. Appendix F Series Screw Torque List Table F-1 Series Screw Torque List SCREW P/N SCREW SPEC Q'ty LOCATION SCREW TORQUE MAA20100302 M2.0*12( 銀白色 ) 2 PCMCIA CARD BUS TO M/B 1.5~2.0 kgf-cm MACK20040N0 M2.0*4( 銀白色 ) 2 PCMCIA CARD BUS TO M/B 1.5 ~2.0 kgf-cm MACK20040N0 M2.0*4( 銀白色 ) 2 ODD CONN TO M/B ...

Appendix G Appendix G Reliability The following table shows MTBF (Mean Time Between Failures) for each component. Table G-1 MTBF Component Time (hours) LCD 50,000 Keyboard 40,000 HDD 300,000 Removable FDD 30,000 Optical (DVD/CD) drive 60,000 AC adaptor 60,000 Satellite M30X Series Maintenance Manual...