Page 2 - TABLE OF CONTENTS; NOTE FOR OPTIONAL EQUIPMENT INSTALLATION
EO18-33027 TABLE OF CONTENTS Page 1. UNPACKING-------------------------------------------------------------------------------------------------------- 1- 1 1.1 PROCEDURES ---------------------------------------------------------------------------------------------------1- 1 1.2 CHECKS --------------...
Page 6 - The contents of this manual may be changed without notification.
EO18-33027 CAUTION! 1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC. 2. The contents of this manual may be changed without notification. Copyright © 2011 by TOSHIBA TEC CORPORATION All Rights Reserved 570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN
Page 8 - plate to remove the ribbon shaft pad from the printer.; OPEN
1. UNPACKING EO18-33027 1.1 PROCEDURE 1- 2 5) Open the top cover and remove the five pieces of tape. And then, open the ribbon shaft holder plate to remove the ribbon shaft pad from the printer. Top Cover Ribbon Shaft Holder Plate Ribbon Shaft Pad Tape Tape OPEN
Page 9 - Keep the carton and pads for later transport.; INSTALLATION; ) Place the printer on the level surface.
1. UNPACKING EO18-33027 1.2 CHECKS 1- 3 1.2 CHECKS 1) Check for damage or scratches on the printer. 2) Confirm that none of the accessories are missing. The parts below are provided as accessories.
CD-ROM (1 pc.)
Carton Safety precautions Quick installation manual NOTES: Keep the carton and pads...
Page 10 - covers to catch them.
3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT EO18-33027 /MAINTENANCE 3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT/MAINTENANCE 3-1 3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION /MAJOR UNIT REPLACEMENT/MAINTENANCE WARNING! 1. Turn the power off and disconnect ...
Page 11 - Printer Block
3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT EO18-33027 /MAINTENANCE 3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT/MAINTENANCE 3-2 2. Do not remove the screws below. Doing so will require the printer block position adjustment with the jig. 3. Be careful not...
Page 12 - Free; O p e n p o s i t i o n; Ribbon Shaft Holder Plate
3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT EO18-33027 /MAINTENANCE 3.1 OPENING/CLOSING THE TOP COVER 3-3 3.1 OPENING/CLOSING THE TOP COVER When opening the top cover, fully open the top cover to the open position. When closing, softly close it to the close position. 3.2 REMOV...
Page 13 - ) Raise the print head block until it stops.; Print Head Block
3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT EO18-33027 /MAINTENANCE 3.3 OPENING/CLOSING THE PRINTER BLOCK 3-4 4) Raise the print head block until it stops. NOTE: DO NOT excessively push down the print head block to close it. Dosing so may cause a failure of the print head bloc...
Page 14 - REMOVING THE OPERATION PANEL; removed from the printer.; Hooks
3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT EO18-33027 /MAINTENANCE 3.4 REMOVING THE OPERATION PANEL 3- 5 3.4 REMOVING THE OPERATION PANEL 1) Open the top cover. (Refer to section 3.1.) 2) Remove the side panel (L) from the printer. (Refer to section 3.2.) 3) Fully open the to...
Page 15 - Operation Panel Ass’y
3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT EO18-33027 /MAINTENANCE 3.4 REMOVING THE OPERATION PANEL 3- 6 6) Disconnect the operation panel harness from the operation panel ass’y. Operation Panel Ass’y Operation Panel Harness
Page 16 - INSTALLATION PROCEDURE FOR OPTIONAL; Disc cutter
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 4- 1 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT WARNING! 1. Make sure to unplug the power cord before installing the optional equipment. 2. Be careful not to pinch your fingers or hands...
Page 17 - Front Plate
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.1DISC CUTTER (B-EX204-QM-R) 4- 2 4.1 DISC CUTTER (B-EX204-QM-R) WARNING! Be careful not to injure your fingers when installing the cutter unit. All the following parts are supplied with the kit. Make sure you have all items shown below. D...
Page 19 - Cord Bush; Cutter Cover; Print Head Cleaner; Frame A and Rotary Cutter Frame B, respectively.
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.2 ROTARY CUTTER (B-EX204-R-QM-R) 4- 4 4.2 ROTARY CUTTER (B-EX204-R-QM-R) WARNING! Be careful not to injure your fingers when installing the cutter unit. All the following parts are supplied with the kit. Make sure you have all items shown...
Page 21 - Cutter Paper Guide C
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.2 ROTARY CUTTER (B-EX204-R-QM-R) 4- 6 NOTE: When attaching the B-8204-QM cutter module, replace the original cutter paper guide C with the enclosed B-SX cutter paper guide C using the following procedure. (1) Remove the two M-4x6 Set Scre...
Page 22 - Hooker
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.2 ROTARY CUTTER (B-EX204-R-QM-R) 4- 7 1) Turn the power off and disconnect the power cord. 2) Open the top cover, and push up the hooker and take out the front cover bottom. 3) Remove the three M3x6 screws from the side panel (L). Move th...
Page 23 - Harness Ass’y
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.2 ROTARY CUTTER (B-EX204-R-QM-R) 4- 8 5) Connect the 9-pin connector of the harness ass’y to CN7 on the cutter driver unit, respectively. 6) Fit the bush to the harness ass’y in the orientation as shown below. 7) Insert the harness ass’y ...
Page 24 - 1) Open the ribbon shaft holder plate.; Main PC Board
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.2 ROTARY CUTTER (B-EX204-R-QM-R) 4- 9 8) Fix the harness ass’y with the clamp. 9) Connect the 9-pin connector of the harness ass’y to CN15, and 2-pin connector to CN18 on the Main PC board, respectively. 10) Turn the head lever counterclo...
Page 25 - Cutter Unit
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.2 ROTARY CUTTER (B-EX204-R-QM-R) 4- 10 13) Connect the four harnesses of the cutter unit to CN8, CN10, CN11 and CN12 on the cutter drive unit. 14) Fit the two tabs of the cutter drive unit into the notches, and then fix the cutter unit wi...
Page 26 - Screw
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.2 ROTARY CUTTER (B-EX204-R-QM-R) 4-11 15) Attach the cutter cover to the cutter unit with the two screws so that the tab of the cutter cover turns on the cutter cover open switch. NOTES: 1. Be careful not to pinch the cutter harness by th...
Page 29 - Rewinder Ass’y
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.3 PEEL OFF MODULE (B-EX904-H-QM-R) 4-14 5) Align the notch of the take-up holder with the screw hole of the rewinder ass’y, and attach them to the printer with the four M-3x6 screws and the M-3x6 screw. 6) Attach the rewind full sensor (L...
Page 30 - Hole
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.3 PEEL OFF MODULE (B-EX904-H-QM-R) 4-15 8) Insert the longer harness of the rewind full sensor (Tr) into the hole in the printer frame. Fit the bush into the hole. 9) Connect the longer harness of the rewind full sensor (Tr)and the rewind...
Page 31 - Selection Switch
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.3 PEEL OFF MODULE (B-EX904-H-QM-R) 4-16 NOTES: 1. You should change the selection switch setting depending on the issue mode. Improper setting may affect the print quality. STANDARD/PEEL OFF (STRIP): Batch or strip mode REWINDER: Built-in...
Page 32 - TBD
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.3 PEEL OFF MODULE (B-EX904-H-QM-R) 4-17 13) Raise the print head block until it stops. 14) Secure the strip sensor (LED) and strip sensor (Tr) to the printer with the M4x6 screws. 15) Connect the shorter harness of the strip sensor (Tr) t...
Page 34 - Adjustment Knob
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.3 STRIP MODULE (B-EX904-H-QM-R) 4-19 20) When using the printer in batch mode or strip mode, attach the front plate removed in step 2). 21) When using the printer in built-in rewinder mode, attach the rewinder guide plate to the front of ...
Page 35 - RSV PC Board
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.4 RIBBON SAVING MODULE (B-EX904-R-QM-R) 4-20 4.4 RIBBON SAVING MODULE (B-EX904-R-QM-R) All the following parts are supplied with the kit. Make sure you have all items shown below. NOTE: The ribbon saving module is standard on the B-EX4T s...
Page 36 - Lock
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.4 RIBBON SAVING MODULE (B-EX904-R-QM-R) 4-21 4) Secure the RSV PC board to the printer with the locking supports. NOTE: Do not push the center of the RSV PC board when attaching it to the printer. Doing so may break the PC board. Hold the...
Page 38 - Packing List; Installation Manual (1 copy; Installation Procedure; Be careful not to pinch your fingers or hands with the covers.
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.5 USB INTERFACE BOARD (B-EX700-RTC-QM-R) 4-23 4.5 RTC/USB Host I/F Card (B-EX700-RTC-QM-R) This optional interface board is provided with the interface port, which allows for the installation of USB devices. Packing List The following par...
Page 39 - Connector J21
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.5 USB INTERFACE BOARD (B-EX700-RTC-QM-R) 4-24 Step 2. Remove the Blind Plate C from the back. Step 3. Install the B-EX700-RTC-QM-R RTC/USB host I/F card in the printer. And fix the 2 M-3x6 screws from the back. Step 4. Connect the RTC/USB...
Page 41 - Remove the Blind Plate D from the back.; Blind Plate D
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.6 EXPANSION I/O INTERFACE BOARD (B-EX700-IO-QM-R) 4-26 Installation Procedure Step 1. Remove the three M3x6 screws from the side panel (L). Move the side panel (L) to the back and push up it to remove. Step 2. Remove the Blind Plate D fro...
Page 42 - Reassemble the side panel (L) in the reverse order of removal.
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.6 EXPANSION I/O INTERFACE BOARD (B-EX700-IO-QM-R) 4-27 Step 4. Connect the Expansion I/O Board harness to J3 on the Main PC Board. Step 5. Reassemble the side panel (L) in the reverse order of removal. Step 6. Perform a loop back check to...
Page 47 - Remove the Blind Plate A from the back.; Blind Plate A
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33027 4.8 Parallel I/F card (B-EX700-CEN-QM-R) 4-32 Installation Procedure Step 1. Remove the three M3x6 screws from the side panel (L). Move the side panel (L) to the back and push up it to remove. Step 2. Remove the Blind Plate A from the back....
Page 49 - MODE; LED Illuminates
5. SYSTEM MODE EO18-33027 5.1 OPERATION PANEL 5-1 5. SYSTEM MODE The system mode can be entered by the following procedure from printer power off condition. • Press [FEED] key and [PAUSE] key at the same time • Press [MODE] Key In this mode, the printer self-test operation and parameter setting oper...
Page 51 - Outline of Self-Diagnostic Test
5. SYSTEM MODE EO18-33027 5.3 SELF-DIAGNOSTIC TEST 5-3 5.3 SELF-DIAGNOSTIC TEST Outline of Self-Diagnostic Test In the Self-Diagnostic Test mode ,the printer checks and prints out the printer system information such as the sensor or interface, and the Maintenance Counter. Also it makes the print h...
Page 52 - Menu operation procedure example
5. SYSTEM MODE EO18-33027 5.3 SELF-DIAGNOSTIC TEST 5-4 • Menu operation procedure example English Procedure Press [FEED] key and [RESTART] key when turning on the printer. Display 「 System Mode / SYSTEM MODE 」 . Select <1>Diagnostics/<1>DIAG. 」 and press [ENTER] Key. Display 「 <1>D...
Page 53 - COUNTER PARAMETE PRINT CONTENTS
5. SYSTEM MODE EO18-33027 5.3 SELF-DIAGNOSTIC TEST 5-5 • COUNTER PARAMETE PRINT CONTENTS << COUNTER >> TOTAL FEED 0.0km [QM] FEED 0.0km FEED1 0.0km FEED2 0.0km FEED3 0.0km FEED4 0.0km PRINT 0.0km PRINT1 0.0km PRINT2 0...
Page 54 - Every cut operation is counted.
5. SYSTEM MODE EO18-33027 5.3 SELF-DIAGNOSTIC TEST 5-6 Print condition: Label length 490mm Print method Setting by user Sensor type Non 203dpi 6ips Speed 305dpi 5ips Issuing number 1 piece Issuing mode Setting by user Other No mount winding motor << COUNTER >> Item Content Range Count co...
Page 60 - RTS protocol
5. SYSTEM MODE EO18-33027 5.3 SELF-DIAGNOSTIC TEST 5-12 2 2bit NONE Non parity. ODD Odd parity. PARITY Parity selection EVEN Even parity. XON/XOFF XON/XOFF protocol (No XON output when the power is on, no XOFF output when the power is off) READY/BUSY READY/BUSY (DTR) protocol (No XON output when the...
Page 64 - USB MEMORY NG
5. SYSTEM MODE EO18-33027 5.3 SELF-DIAGNOSTIC TEST 5-16 5.3.2 Auto Diagnostics/AUTO DIAGNOSTICS The printing procedure of “AUTO DIAGNOSTIC” of “DIAG.” is same as 「 5.3.1 Counter, Parameter/ MAINTENANCE COUNT 」 . The manu layer from top menu of system mode to AUTO DIAGNOSTICS is below. MENU ITEM Syst...
Page 67 - Resistance
5. SYSTEM MODE EO18-33027 5.3 SELF-DIAGNOSTIC TEST 5-19 SENSOR2 [H]20 ﾟ C [A]22 ﾟ C Open-air temperature sensor status 0 to 86 °C, --°C if it cannot be detected) Thermal head temperature sensor status (0 to 86 °C) [R]4.2V [T]2.5V [E]2.7V Reflective sensor status for detecting the ribbon end state (0...
Page 70 - BASIC S NONE
5. SYSTEM MODE EO18-33027 5.3 SELF-DIAGNOSTIC TEST 5-22 USB memory mounts check contents USB MEMORY NG OK: Mounted NG: Not mounted USB memory BASIC program check contents BASIC M NONE NONE: No program Version: Program exist BASIC main program BASIC S NONE NONE: No program Version: Program exist BASI...
Page 72 - PARAMETER SETTING; Outline of Parameter Setting; Parameter Setting; menu contains the following:
5. SYSTEM MODE EO18-33027 5.4 PARAMETER SETTING 5-24 5.4 PARAMETER SETTING Outline of Parameter Setting In the Parameter Setting mode, various kinds of parameters, such as communication, key, LCD, etc. can be set. This will allow the use of the printer to comply with your operating conditions. The...
Page 74 - Disable ribbon save function
5. SYSTEM MODE EO18-33027 5.4 PARAMETER SETTING 5-26 5.4.1.6 Ribbon save / RBN SAVE ・ Tag / TAG Enable ribbon save function (Head open/close lever: Tag position) ・ Label / LABEL Enable ribbon save function (Head open/close lever: Label position) ） ・ Disable / OFF Disable ribbon save function (...
Page 79 - “X” indicates the remaining number of labels.)
5. SYSTEM MODE EO18-33027 5.4 PARAMETER SETTING 5-31 5.4.2.12 Ribbon near end / RBN NEAR END ・ Disable / OFF Disable ribbon near end detection ・ 30m Enable ribbon near end: Remaining 30 m (Ribbon diameter is 38 mm) ・ 70m Enable ribbon near end: Remaining 70 m (Ribbon diameter is 43 mm) (*) The...
Page 80 - XML
5. SYSTEM MODE EO18-33027 5.4 PARAMETER SETTING 5-32 Example of TYPE2 「 Case 1 」 Issuing number = 5, When label end is detected at 3 rd label issuing. (1) (2) (3) ↑ Stop by error after (3), LCD: “NO PAPER 2” When printer is restarted, issue (4) (5) after initial feed. The complete issued label is (1...
Page 85 - Fine adjustment value setting/ ADJUST SET; Outline of Printer Parameter Fine Adjustment
5. SYSTEM MODE EO18-33027 5.5 PRINTER PARAMETER FINE ADJUSTMENT 5-37 5.5 Fine adjustment value setting/ ADJUST SET Outline of Printer Parameter Fine Adjustment In the Printer Parameter Fine Adjustment mode, you can fine adjust each parameter, such as Print tone, Print start position, Threshold, et...
Page 86 - 単位
5. SYSTEM MODE EO18-33027 5.5 PRINTER PARAMETER FINE ADJUSTMENT 5-38 5.5.1 Feed / FEED ADJ. Max. Min. Step Display Sign Integer digit Decimal point digit 0 fullfil 単位 50.0 -50.0 0.1 Decimal Exist 2 1 Non mm +0.0mm Label 1 piece Print start position +3.0mm Label 1 piece Print start position -3.0mm La...
Page 87 - Cut position; performed with the head lifted, the head may not be lifted.
5. SYSTEM MODE EO18-33027 5.5 PRINTER PARAMETER FINE ADJUSTMENT 5-39 +3.0mm Cut position -3.0mm Cut position Paper feed direction [Procedure for label having label pitch of less than 38 mm when the swing cutter is used] The minimum label pitch of the label which can be cut in normal use is 38.0 mm. ...
Page 88 - (a) Cut position fine adjustment value calculation; Operation example; Label pitch
5. SYSTEM MODE EO18-33027 5.5 PRINTER PARAMETER FINE ADJUSTMENT 5-40 (1) Idling (2) Completes printing the first label (A). (3) Feeds the label to the cut position, then cuts the gap at the front of label (A). (4) Back feeds to the home position. (5) Completes printing the second label (B). (6) Feed...
Page 89 - ejected passes the paper feed roller, the sensor may not be able to
5. SYSTEM MODE EO18-33027 5.5 PRINTER PARAMETER FINE ADJUSTMENT 5-41 [Procedure for label having less than the min. label pitch for each issue speed when the rotary cutter is used] When the following conditions are all met, the cut operation for the last label to be cut is as follows. Forward feed t...
Page 90 - mm
5. SYSTEM MODE EO18-33027 5.5 PRINTER PARAMETER FINE ADJUSTMENT 5-42 [Strip position fine adjustment] 0.0 ｍｍ +3.0mm -3.0mm 4mm 3mm ▼ 2mm Printing in strip issue mode is stopped at the position where the distance from the middle point of the gap between labels to the end of the strip shaft is 4 mm, s...
Page 94 - Supplementary explanation
5. SYSTEM MODE EO18-33027 5.5 PRINTER PARAMETER FINE ADJUSTMENT 5-46 5.5.9 Refrective sensor fine tune / THRESHOLD <REFL.> Max. Min. Step Display Sign Integer digit Decimal point digit 0 fullfil Unit 4.0 0.0 0.1 Decimal Non 1 1 Non V （ * ） If “0.0 V” is set, when the power is turned OFF then O...
Page 95 - Speed
5. SYSTEM MODE EO18-33027 5.5 PRINTER PARAMETER FINE ADJUSTMENT 5-47 fine adjustment values are ±10. The max. value for each print speed is as below. When the value exceeds the maximum, it is automatically corrected to the max. value. B-EX4T1-G B-EX4T1-T Speed Direct thermal Thermal transfer Direct ...
Page 96 - Outline of Test Print; Test Print
5. SYSTEM MODE EO18-33027 5.6 TEST PRINT 5-48 5.6 TEST PRINT Outline of Test Print In the Test Print mode, you can print the test pattern and set its conditions. This is useful to check the print quality of new media or ribbon. The Test Print menu contains the following: MENU ITEM System Mode / SY...
Page 103 - SENSOR ADJUSTMENT; Outline of the Sensor Adjustment
5. SYSTEM MODE EO18-33027 5.7 SENSOR ADJUSTMENT 5-55 5.7 SENSOR ADJUSTMENT Outline of the Sensor Adjustment In the Sensor Adjustment mode, the status of the sensors and thermistors is displayed. Also you can make a Threshold Setting for the Black Mark, Feed Gap, and Ribbon End Sensors. The Sensor ...
Page 105 - クリア
5. SYSTEM MODE EO18-33027 5.8 RAM CLEAR 5-57 5.8 RAM CLEAR Outline of RAM Clear In the RAM Clear mode, clearing the Maintenance Counter and initializing the Parameters are possible. After replacing the print head, ribbon motor, or platen, perform maintenance clear. The RAM Clear menu contains the ...
Page 112 - IP ADDRESS SETTING; Outline of the IP Address Setting; IP Address Setting
5. SYSTEM MODE EO18-33027 5.9 IP ADDRESS SETTING 5-64 5.9 IP ADDRESS SETTING Outline of the IP Address Setting In the IP Address Setting mode, you can set the IP Address, Gateway Address, Subnet Mask, DHCP, and DHCP ID which are necessary for a network communication. Since each setting value is di...
Page 120 - Outline of Basic Setting
5. SYSTEM MODE EO18-33027 5.10 BASIC SETTING 5-72 5.10 BASIC SETTING Outline of Basic Setting The Basic function enables the B-SX4T/SX5T printer to operate with the program created for other printers, by converting it to Basic program and downloading this Basic program to the B-SX4T/SX5T printer. ...
Page 121 - RFID Module Setting; Outline of the RFID Module Setting
5. SYSTEM MODE EO18-33027 5.11 RFID Module Setting 5-73 5.11 RFID Module Setting Outline of the RFID Module Setting In the RFID Module Setting mode, you can set various parameters related to the RFID module. It is necessary to set these parameters before operating the RFID module. If a read or wri...
Page 130 - Example 1
5. SYSTEM MODE EO18-33027 5.11 RFID Module Setting 5-82 5.11.4.5 Write retry minimum AGC / WRITE RETRY MIN AGC It is applicable for only B-SX704-RFID-U2-R/EU-R/US-R/US-R. When the Q value is set to 1 or greater, the AGC threshold lower limit for retry becomes effective. Even if a tag’s gain is lower...
Page 132 - LCD Display example; not used by any other devices.; Strength; “MAX 0011” means the value of the maximum radio wave picked up.
5. SYSTEM MODE EO18-33027 5.11 RFID Module Setting 5-84 5.11.5.2 Multi word write / MULT WRITE Gen2-compatible Hibiki tag (HITACHI) has a function which reduces the time to write data on the RFID chips. This is called “Multi-word writes”. Use of this function enables a speed-up of the data write ope...
Page 133 - LED function; ]LED; Key function
6. ON LINE MODE EO18-33027 6. ON LINE MODE 6- 1 6. ON LINE MODE In the ON LINE mode, the following settings can be performed. Threshold Setting for the Feed Gap Sensor Threshold Setting for the Black Mark Sensor Reset Parameter Settings Printer Parameter Fine Adjustment Dump Mode LED function Indi...
Page 134 - Error messages; Error Messages; Close the Print Head Block.; COMMS ERROR; A communication error has occurred.
6. ON LINE MODE EO18-33027 6. ON LINE MODE 6- 2 (1) Resumes printing after a temporary stop of label printing or after an error. (2) Places the printer in the usual initial state which is obtained when the power is turned on. [RESTART] (3) Switches to user mode. (1) Stops label printing temporarily....
Page 138 - shown on 3
6. ON LINE MODE EO18-33027 6. ON LINE MODE 6- 6 word data from a place other than the boundary of the long word data (d) Access to the area of 80000000H to FFFFFFFFH in the logic space in the user mode. (e) Undefined command placed in other than the delay slot has been decoded. (f) Undefined command...
Page 140 - THRESHOLD SETTING; Threshold
6. ON LINE MODE EO18-33027 6.1 THRESHOLD SETTING 6- 8 6.1 THRESHOLD SETTING When a label is printed, the printer detects the gap between the labels using the transmissive sensor, and corrects the print position automatically to obtain a constant print position. However, when a preprinted label is us...
Page 141 - Judgment display
6. ON LINE MODE EO18-33027 6.1 THRESHOLD SETTING 6- 9 [Threshold setting] 6b. Judgement: NG ↓ ↓ ↓ [ENTER] key Move to “7a/7b. Detail” by pressing [RIGHT] Key ↓ Press [RIGHT] Key ↓ [Threshold setting] 7a. Detail: OK ↓ ↓ ↓ ↓ ↓ ↓ Move to “8a. Sensor Fine adjustment” by pressing [RIGHT] key Move to “6a....
Page 143 - ONLINE MODE LCD DISPLAY; ONLINE MODE LCD DISPLAY EXAMPLE
6. ON LINE MODE EO18-33027 6.3 HELP DISPLAY 6- 11 6.2 ONLINE MODE LCD DISPLAY 1. ONLINE MODE LCD DISPLAY EXAMPLE （ English ） Printer condition LCD Display Display contents ← Model name, Version No. (*5) ← Message ← Printing page number (*1) ← IP address etc. (*4) Online ← Icon ← Remaining page numbe...
Page 145 - Open
6. ON LINE MODE EO18-33027 6.3 HELP DISPLAY 6- 13 z It is used when RFID module is mounted. It is not displayed when RFID module is not mounted. z It is ON when module is enabled and ready to communicate. z It blinks when module is communicating and processing. - The communication includes the one n...
Page 146 - EXPLANATION OF HELP DISPLAY; Error
6. ON LINE MODE EO18-33027 6.3 HELP DISPLAY 6- 14 Stop printing if printing and, Help guide is displayed since there is help message. Help message for paper empty (*1) 6.3 HELP DISPLAY EXPLANATION OF HELP DISPLAY The help display can be shown by pressing [RIGHT] key or [ENTER] key in case help guide...
Page 147 - English; Online mode; Error recovery method
6. ON LINE MODE EO18-33027 6.3 HELP DISPLAY 6- 15 HELP DISPLAY TRANSITION, OPERATION EXAMPLE （ English ） Display transition [LEFT]Key [CANCEL] Key Display transition [RIGHT] Key [ENTER] Key Online mode Error content Scroll display by [UP] Key and [DOWN] Key Error managing method Scroll display by [U...
Page 148 - PERIODIC MAINTENANCE PROCEDURE
7. PERIODIC MAINTENANCE PROCEDURE EO18-33027 7. PERIODIC MAINTENANCE PROCEDURE 7- 1 7. PERIODIC MAINTENANCE PROCEDURE All machines are generally delivered in their best condition. To maintain optimal operating condition and help gain maximum performance and life of machines, we would recommend you t...
Page 149 - Loosen the two Plastic Head Screws to remove the Cutter Cover.; Media Path
7. PERIODIC MAINTENANCE PROCEDURE EO18-33027 7. PERIODIC MAINTENANCE PROCEDURE 7- 2 (4) Remove paper debris or label glue from the media path. (5) When using the cutter unit, clean the cutter blade and the media path. WARNING! When cleaning the cutter, be careful not to be injured by the cutter blad...
Page 151 - When the Strip Module is used; When labels skew to the right:
7. PERIODIC MAINTENANCE PROCEDURE EO18-33027 7. PERIODIC MAINTENANCE PROCEDURE 7- 4 10. Conduct the following tests and make sure that there is no problem. (1) Print test with TOSHIBA TEC-approved media and ribbon. (Print tone, print head position, etc.) (2) Paper skew When the Strip Module is used;...
Page 154 - RFID ANALYZE TOOL; RFID tag type; System Requirement
11. RFID ANALYZE TOOL EO18-33027 11.1 Sstem Requirement 11- 1 11. RFID ANALYZE TOOL When an RFID module is installed, the printer will be able to write data on an RFID tag as well as print data on the surface of the RFID-tag embedded label. To properly issue RFID tags, it may be necessary to adjust ...
Page 156 - Application Functions
11. RFID ANALYZE TOOL EO18-33027 11.3 Application Functions 11- 3 11.3 Application Functions 11.3.1 Main Menu (1) Front Feed amount: +9999 ~ -9999 (6) Write Test Button (2) Back Feed amount: +9999 ~ -9999 (7) Read Test Button (3) Number of test tries: 999 ~ 0 (8) Test Stop Button (4) RFID module sel...
Page 157 - Antenna Kind Information
11. RFID ANALYZE TOOL EO18-33027 11.3 Application Functions 11- 4 11.3.2 File Menu (1) Log Information Set Displays the Test Information Setting screen shown below. Make necessary settings and click on the “OK” button. 1) Antenna Kind Information 2) Antenna Position: “Upper”, “Lower”, “In addition t...
Page 158 - Log Save As
11. RFID ANALYZE TOOL EO18-33027 11.3 Application Functions 11- 5 (2) Log Save As Saves text data in the “Results” box of the RFID Analyze Tool screen into a text file. (3) Text Capture Saves the test result into a CSV file. Selecting “Text Capture” then “Open” shows “Capture” in the area indicated ...
Page 159 - Exits from the Analyze Tool program.
11. RFID ANALYZE TOOL EO18-33027 11.3 Application Functions 11- 6 (5) End (Exit) Exits from the Analyze Tool program. Communication Settings between PC and Printer (Serial Port Setting) Feed Amount RFID Module Type Tag Type Number of Tries Sheet Count Label Size Command Feed Command Printer type
Page 161 - Makes settings for communication between the PC and the printer.; Serial port may not be selectable depending on the printer types.
11. RFID ANALYZE TOOL EO18-33027 11.3 Application Functions 11- 8 (2) CommSetting Makes settings for communication between the PC and the printer. NOTES: 1. In the case of the LAN interface, a socket communication is used. 2. Serial port may not be selectable depending on the printer types. 3. The a...
Page 163 - Setting
11. RFID ANALYZE TOOL EO18-33027 11.3 Application Functions 11- 10 (5) Sheet Setting Makes settings for the media to be used. Sheet Inf. 1) Sheet Count: The number of tags to be tested. (1 ~ 5) After printing on one label, a next tag is automatically fed to continue the test. LabelSize Command 2) Si...
Page 164 - Select the printer model; NOTE: This information can be saved by a parameter save function.; Select the test mode
11. RFID ANALYZE TOOL EO18-33027 11.3 Application Functions 11- 11 (7) Select the printer model Makes a choice of a printer model from Get Printer Type menu. Choose “B-SX4T/SX5T”. NOTE: This information can be saved by a parameter save function. (8) Select the test mode This menu is not available.
Page 165 - Displays Printer Version and RFID Module Version.; Example; Example) CSV file information; Printer Version
11. RFID ANALYZE TOOL EO18-33027 11.3 Application Functions 11- 12 11.3.4 Help Menu Displays Printer Version and RFID Module Version. Example NOTE: Printer version and module version are indicated next to the date and time of Log file. Example) CSV file information Date&Time = 07/10/16 09:47:24:...
Page 166 - Operating Procedure
11. RFID ANALYZE TOOL EO18-33027 11.4 Operating Procedure 11- 13 11.4 Operating Procedure 1. Connect the printer to the PC with the serial interface cable or LAN cable. 2. Start the “B-SX RFID Analyze Tool” application.
Page 168 - printer is acceptable.
11. RFID ANALYZE TOOL EO18-33027 11.4 Operating Procedure 11- 15 4. When the “CommSetting” screen appears, perform the serial port or LAN setting in accordance with the settings of the B-EX4T/EX6T printer. NOTES: 1. Choose the port to which the printer is connected. 2. Choose “NON” for the Flow cont...
Page 169 - RFID module type to be analyzed (RFID Module Select); RFID Module Select
11. RFID ANALYZE TOOL EO18-33027 11.4 Operating Procedure 11- 16 4. Set the following parameters. RFID module type to be analyzed (RFID Module Select) Choose the RFID module to be used for the RFID Module Select parameter. B-EX700-RFID-H1-QM-R: “H1” B-EX700-RFID-U2-EU/US-R: “U2” RFID Module Select
Page 170 - RFID module type; Tag; Tag Type
11. RFID ANALYZE TOOL EO18-33027 11.4 Operating Procedure 11- 17 RFID tag type to be analyzed (Tag type) Selectable tag types are different depending on the RFID module types. RFID module type Tag type H1: B-EX700-RFID-H1-QM-R C220 (H1), I-Code (H1), ISO15693 (H1), Tag-it (H1) and C320 (H1) U2: B-EX...
Page 171 - Set the feed amount range where an RFID tag is analyzed.
11. RFID ANALYZE TOOL EO18-33027 11.4 Operating Procedure 11- 18 Feed amount range (Front/Back Feed) Set the feed amount range where an RFID tag is analyzed. Upper limit (Reverse feed amount): 0 – 9990 (in units of 0.1 mm) Lower limit (Forward feed amount): 0 – 9990 (in units of 0.1 mm) The values c...
Page 172 - Write test
11. RFID ANALYZE TOOL EO18-33027 11.4 Operating Procedure 11- 19 5. Perform a write test or read test. Write test Click on the “Write Test” button to start a write test. During the write test, total number of successful write and total number of write performed are shown in the status bar. In the te...
Page 173 - All read or write test results; Write/Read Results Box
11. RFID ANALYZE TOOL EO18-33027 11.4 Operating Procedure 11- 20 Status bar Text box Results box Write Test button Status Data All read or write test results Read Test button Write/Read Results Box Total number of tests Total number of succeeded tests Feed amount Tag ID Example (U1 module)
Toshiba 26C100U
User Manual
Toshiba 55SL412U
User Manual
Toshiba 50L5200U
User Manual
Toshiba 24V4210U
User Manual
Toshiba 40L3400U
User Manual
Toshiba 50L1350U
User Manual
Toshiba 24SLV411U
User Manual
Toshiba 50L2400U
User Manual
Toshiba 58L7350U
User Manual
Toshiba 50L1400U
User Manual