Toro 38755 - Manuals

Setup 1 Unfolding the Handle No Parts Required Procedure g287662 2 Installing the Recoil-Start Guide and Rope No Parts Required Procedure g286483 5

3 Installing the Discharge Chute No Parts Required Procedure g287665 4 Filling the Engine with Oil No Parts Required Procedure g286445 6

5 Adjusting the Control Cable No Parts Required Procedure Refer to Adjusting the Control Cable (page 15) . 7

Product Overview g291536 Figure 8 1. Chute deflector 5. Control bar 2. Chute-deflector trigger 6. Oil-drain plug 3. Chute handle 7. Oil fill/dipstick 4. Fuel-tank cap g280282 Figure 9 1. Recoil-start handle 5. Key 2. Electric-start plug-in(electric-start models only) 6. Primer 3. Electric-start butt...

Operation Note: Determine the left and right sides of the machine from the normal operating position. Before Operation Before Operation Safety General Safety • For electric-start models only: Use extension cords and receptacles as specified in the manual.Inspect the electrical cord before plugging i...

Checking the Engine-Oil Level Service Interval: Before each use or daily—Check the engine-oil level and add oil if necessary. g293393 Figure 11 10

During Operation During Operation Safety General Safety • Shut off the engine before unclogging themachine and always use a stick or thesnow-cleanout tool (if provided). • Stay behind the handles and away from thedischarge opening while operating the machine. Keep your face, hands, feet, and any oth...

Clearing a CloggedDischarge Chute To clear the chute: • Shut the engine off! • Wait 10 seconds to ensure that the rotor bladeshave stopped rotating. • Always use a clean-out tool; never use your hands. Operating Tips WARNING The rotor blades can throw stones, toys,and other foreign objects and cause...

Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first hour • Check the control cable and adjust it if necessary. After the first 2 hours • Change the engine oil. Before each use or daily • Check the engine-oil level and add oil if necessar...

Adjusting the Control Cable 1. Slide up the spring cover and unhook the springfrom the adjuster link ( Figure 17 ). g006402 Figure 17 1. Adjuster link 3. Spring cover 2. Z-fitting 4. Unhook the spring here. Note: You can pull up the adjuster link and cable to make unhooking the spring easier. 2. Mov...

Changing the Engine Oil Service Interval: After the first 2 hours Yearly If possible, run the engine for a few minutes beforechanging the oil to warm it. Warm oil flows better andcarries more contaminants. Engine Oil Specifications Engine oil capacity 0.70 L (24 fl oz)* Oil viscosity Refer to Figure...

g006374 Figure 23 9. Wait 3 minutes for the oil to settle in the engine. 10. Wipe the dipstick clean with a clean cloth. 11. With the machine in the operating position,insert the dipstick into the oil-fill tube, but do not screw it in , then remove the dipstick. 12. Read the oil level on the dipstic...

Replacing the Drive Belt If the drive belt becomes worn, oil-soaked, excessivelycracked, frayed, or otherwise damaged, replace thebelt. 1. Remove the drive-belt cover by removing the 3bolts as shown in Figure 26 . g008238 Figure 26 1. Drive-belt cover 6. Drive belt 2. Bolt (3) 7. Rotor shaft 3. Roto...

Storage Storage Safety • Shut off the engine, remove the key, and waitfor all movement to stop before you leave theoperator’s position. Allow the machine to coolbefore adjusting, servicing, cleaning, or storing it. • Fuel fumes are highly flammable, explosive, anddangerous if inhaled. If you store t...

California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in C...