Toro 37799 - User Manual

Toro 37799 Snow Blower – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 2 – WARNING; Contents; Safety; General Safety
Page 3 – Safety and Instructional Decals
Page 5 – Setup; Installing the Upper Handle; Procedure; Procedure
Page 6 – Installing the Traction-Control Linkage
Page 7 – Installing the Chute-Control Rod
Page 8 – Installing the Snow-Cleanout Tool; Checking the Engine-Oil Level
Page 9 – Checking the Tire Pressure; CAUTION
Page 10 – Product Overview
Page 11 – Specifications; Attachments/Accessories; Operation; Before Operation; Before Operation Safety; Fuel Safety
Page 12 – Filling the Fuel Tank; During Operation; During Operation Safety
Page 13 – Starting the Engine
Page 14 – Standard Model; Shutting Off the Engine
Page 15 – Operating the Quick Stick®; Moving the Discharge Chute
Page 16 – Moving the Chute Deflector
Page 17 – Operating Tips; DANGER; After Operation; After Operation Safety
Page 18 – Maintenance; Maintenance Safety; Preparing for Maintenance
Page 22 – Changing the Engine Oil; Lubricating the Hex Shaft
Page 23 – Replacing the Spark Plug
Page 24 – Replacing the Drive Belts
Page 25 – Replacing the Headlight; Storage; Storing the Machine
Page 26 – Troubleshooting
Page 28 – California Proposition 65 Warning Information

Loading the manual

Form No. 3423-315 Rev B

Power Max

824 OE and 826 OXE Snowthrower

Model No. 37798—Serial No. 400000000 and Up

Model No. 37799—Serial No. 400000000 and Up

Operator's Manual

Introduction

This machine is intended to be used by residential
homeowners. It is designed primarily for removing
snow from paved surfaces, such as driveways and
sidewalks, and other surfaces for traffic on residential
or commercial properties. It is not designed for
removing materials other than snow.

Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely.

You may contact Toro directly at www.Toro.com
for product safety and operation training materials,
accessory information, help finding a dealer, or to
register your product.

Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready.

Figure 1

identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.

Important:

With your smartphone or tablet, scan

the QR code on the serial number decal to access
warranty, parts, and other product information.

g219962

Figure 1

Model and serial number location

Model No.

Serial No.

This manual identifies potential hazards and has
safety messages identified by the safety-alert symbol
(

Figure 2

), which signals a hazard that may cause

serious injury or death if you do not follow the
recommended precautions.

g000502

Figure 2

Safety-alert symbol

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical

information and

Note

emphasizes general information

worthy of special attention.

Important:

If you are using this machine above

1500 m (5,000 ft) for a continuous period, ensure
that the High Altitude Kit has been installed
so that the engine meets CARB/EPA emission
regulations. The High Altitude Kit increases
engine performance while preventing spark-plug
fouling, hard starting, and increased emissions.
Once you have installed the kit, attach the
high-altitude label next to the serial decal on the
machine. Contact any Authorized Toro Service
Dealer to obtain the proper High Altitude Kit and
high-altitude label for your machine. To locate
a dealer convenient to you, access our website
at www.Toro.com or contact our Toro Customer
Care Department at the number(s) listed in your
Emission Control Warranty Statement. Remove
the kit from the engine and restore the engine to
its original factory configuration when running the
engine under 1500 m (5,000 ft). Do not operate an
engine that has been converted for high-altitude
use at lower altitudes; otherwise, you could
overheat and damage the engine.
If you are unsure whether or not your machine has
been converted for high-altitude use, look for the
following label (

Figure 3

Original Instructions (EN)

Printed in Mexico

*3423-315* B

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - WARNING; Contents; Safety; General Safety

decal127-9363 Figure 3 WARNING CALIFORNIA Proposition 65 Warning The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Use of this product may cause exposure to chemicals known to the State of California t...

Page 3 - Safety and Instructional Decals

• Keep clear of any discharge opening. Keepbystanders, especially small children, out of theoperating area. • Never allow children to operate the machine. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any areaof potential dange...

Page 5 - Setup; Installing the Upper Handle; Procedure; Procedure

Setup 1 Installing the Upper Handle No Parts Required Procedure g252379 2 Installing the Chute No Parts Required Procedure g252568 5