Toro 38753 - Manuals

Setup 1 Unfolding the Handle No Parts Required Procedure g287663 2 Installing the Recoil-Start Guide and Rope No Parts Required Procedure g286483 5

3 Installing the Discharge Chute No Parts Required Procedure Models 38752 and 38753 g291515 Model 38756 g262492 6

4 Filling the Engine with Oil No Parts Required Procedure g324210 5 Adjusting the Control Cable No Parts Required Procedure Refer to Checking and Adjusting the Control Cable (page 16) . 7

Product Overview g291536 Figure 9 Models 38752 and 38753 1. Chute deflector 5. Control bar 2. Chute-deflector trigger 6. Oil-drain plug 3. Chute handle 7. Oil fill/dipstick 4. Fuel-tank cap g280271 Figure 10 Model 38756 1. Chute deflector 5. Quick Shoot™ control 2. Chute-deflector trigger 6. Oil-dra...

Operation Note: Determine the left and right sides of the machine from the normal operating position. Before Operation Before Operation Safety General Safety • For electric-start models only: Use extension cords and receptacles as specified in the manual.Inspect the electrical cord before plugging i...

Checking the Engine-Oil Level Service Interval: Before each use or daily—Check the engine-oil level and add oil if necessary. g293393 Figure 13 10

During Operation During Operation Safety General Safety • Shut off the engine before unclogging themachine and always use a stick or thesnow-cleanout tool (if provided). • Stay behind the handles and away from thedischarge opening while operating the machine. Keep your face, hands, feet, and any oth...

CAUTION If you leave the machine plugged into a power source, someone can inadvertently start themachine and injure people or damage property (electric-start models only). Unplug the power cord whenever you are not starting the machine. g327424 Figure 14 Using Recoil Start Note: Remove your glove wh...

g280416 Figure 19 To raise or lower the angle of the chute deflector,press the trigger on the chute deflector and move thechute deflector up or down ( Figure 20 ). g006398 Figure 20 1. Chute-deflector trigger 2. Chute deflector Clearing a CloggedDischarge Chute To clear the chute: • Shut the engine ...

Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first hour • Check the control cable and adjust it if necessary. After the first 2 hours • Change the engine oil. Before each use or daily • Check the engine-oil level and add oil if necessar...

Adjusting the Control Cable 1. Slide up the spring cover and unhook the springfrom the adjuster link ( Figure 22 ). g006402 Figure 22 1. Adjuster link 3. Spring cover 2. Z-fitting 4. Unhook the spring here. Note: You can pull up the adjuster link and cable to make unhooking the spring easier. 2. Mov...

Changing the Engine Oil Service Interval: After the first 2 hours Yearly If possible, run the engine for a few minutes beforechanging the oil to warm it. Warm oil flows better andcarries more contaminants. Engine Oil Specifications Engine oil capacity 0.6 L (20 fl oz)* Oil viscosity Refer to Figure ...

g006374 Figure 28 9. Wait 3 minutes for the oil to settle in the engine. 10. Wipe the dipstick clean with a clean cloth. 11. With the machine in the operating position,insert the dipstick into the oil-fill tube, but do not screw it in , then remove the dipstick. 12. Read the oil level on the dipstic...

Storage Storage Safety • Shut off the engine, remove the key, and waitfor all movement to stop before you leave theoperator’s position. Allow the machine to coolbefore adjusting, servicing, cleaning, or storing it. • Fuel fumes are highly flammable, explosive, anddangerous if inhaled. If you store t...

California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in C...