TOA F-2322C2 - Manuals - manualsarea.com

Page 2 - SAFETY PRECAUTIONS; Safety Symbol and Message Conventions; WARNING

2 1. SAFETY PRECAUTIONS • Be sure to read the instructions in this section carefully before use.• Make sure to observe the instructions in this manual as the conventions of safety symbols and messages regarded as very important precautions are included. • We also recommend you keep this instruction ...

Page 3 - GENERAL DESCRIPTION; • Rotating front grille can be installed quickly and conveniently.

3 2. GENERAL DESCRIPTION The F-2322C2 and F-2352C2 are flush-mounted Ceiling Speaker Systems that offer wide frequency rangeand high-quality sound output. The F-2322C2 employs a full-range speaker element, while the F-2352C2 features a 2-way speakerconfiguration.Both speaker systems are designed to ...

Page 4 - NOMENCLATURE AND DIMENSIONS

4 4. NOMENCLATURE AND DIMENSIONS Ceiling tile Ceiling tile ø230 (9 1 / 16 ) 12 ( 15 / 32 ) 200 (7 7 / 8 ) Mounting hole: ø200 (7 7 / 8 ) Mounting hole: ø200 (7 7 / 8 ) ø195 (7 43 / 64 ) Removable inputconnector Safety wire hook Removable inputconnector Safety wire hook Safety wire (accessory)Length:...

Page 5 - Mount fittings to a ceiling or hanging pipe.; Caution

When mounting the speaker to a ceiling, check in advance that the ceiling structure is of drop ceiling with2-foot standard ceiling tiles. 5 5. INSTALLATION The F-2322C2 and F-2352C2 can be mounted in 2 different configurations: • Mounting to a drop ceiling Use the supplied tile bridge. If the mounti...

Page 6 - [If the mounting hole is larger that the specified diameter]; Note; Hanging from a ceiling suspension pipe (exposed installation); Notes

[If the mounting hole is larger that the specified diameter] Use the supplied tile bridge in conjunction with the optional HY-TR1 Trim Ring. Note Refer to the instruction manual included with the HY-TR1 for the correct ceiling mounting procedure. 6 2-2. Hanging from a ceiling suspension pipe (expose...

Page 8 - Connect the speaker cable to the removable input connector.; Tip; The following matching cable types are recommended:

4-2. Insert the stripped cable end into the terminal and tighten the terminal screw with a screwdriver. Note If not making bridge connections,be sure to tighten unused terminalscrews to avoid their vibration. 8 [Hanging from a ceiling suspension pipe] Suspension pipe Safety wire(accessory) Safety wi...

Page 10 - The switch is factory-preset to 330; Important; Never set this switch to low impedance (8

10 6-2. Hanging from a ceiling (in the case of Step 2-2) Follow Step 6-1 to mount. HY-BC1 Back Can attached to suspension pipe(optional) Caution Take care not to pinch the speaker cable and safety wire (supplied with the speaker). Mounting tab Speaker unit Electric screwdriver Step 8. Attach the fro...

Page 11 - Use an electric screwdriver to detach.; REMOVING THE SPEAKER FOR MAINTENANCE; • W h e n l o o s e n i n g t h e m o u n t i n g t a b a x i s; REPAINTING THE SPEAKER; Follow the procedure below when repainting the front grille:; Do not use thinner or other volatile liquids to clean the grille.; Cautions; After the paint has dried, apply another light coat.

11 Mounting tab axis screw Mounting tab Use an electric screwdriver to detach. Screw cap 6. REMOVING THE SPEAKER FOR MAINTENANCE 6.1. Detaching the Front Grille Turn the front grille counterclockwise to full stop, then lightlypull it downward. Tip The front grille employs a double-locking system.If ...

Page 12 - ABOUT THE INPUT OVERLOAD PROTECTION CIRCUITRY

533-06-142-00 9. SPECIFICATIONS Note: The design and specifications are subject to change without notice for improvement. • Optional Components HY-TR1 (Trim Ring): Use this ring when mounting the speaker in pre-existing holes that are larger than the designated 200 mm (7 7 / 8 ") in diameter. HY...