TOA C-RM500 - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS; SAFETY PRECAUTIONS

2 TABLE OF CONTENTS 1. SAFETY PRECAUTIONS .................................................................................... 4 2. GENERAL DESCRIPTION .................................................................................. 5 3. FUNCTIONS .....................................................

Page 4 - regarded as very important precautions are included.; WARNING; may result in fire or electric shock.; CAUTION; time, a fire or damage to the unit may result.

4 1. SAFETY PRECAUTIONS • Be sure to read the instructions in this section carefully before use.• Make sure to observe the instructions in this manual as the conventions of safety symbols and messages regarded as very important precautions are included. • We also recommend you keep this instruction ...

Page 5 - GENERAL DESCRIPTION; • Display Selection; • Camera Position Selection; • Function Key Programming; Equipment Which Can Be Controlled with the C-RM500; Shown below are equipment that can be controlled with the C-RM500.; About the Camera Control Terminal

• The explanations in this manual assume that the C-RM500 Remote Controller is connected to a C-MS160D/S or C-MS90D/S Multi-Switcher and the C-SS8 Smart Switcher. • Camera number: Refers to the camera input terminal number connected to the switcher. • Position number: Combination camera orientation ...

Page 6 - NOMENCLATURE AND FUNCTIONS; Notes; Does not function in systems using only with Combination cameras.

6 4. NOMENCLATURE AND FUNCTIONS [Top] A B C D WIPER ZOOM TELE WIDE FOCUS FAR NEAR LENS SPEED UP DOWN RIGHT LEFT LOW HIGH DEF AUX AUTO E F G H SELECT MENU GROUP CH SEQUENCE FUNCTION ALARM RESET HOLD AF POSITION CONTROL FREEZE FULL WIPER DEF AUX AUTO AF POSITION CONTROL FREEZE FULL REMOTE CONTROLLER C...

Page 8 - U s e d t o d e s i g n a t e t h e c a m e r a t o b e m a n u a l l y; (Function indications for the rear parts); Slave unit remote control terminal

8 27. Position key Orients the Combination camera toward the setdirection. The Position key can only be usedwhen the Control indicator is on. Pressing thePosition key without designating the positionnumber orients the camera toward the directionp r o g r a m m e d u n d e r P o s i t i o n N o . 1 (...

Page 9 - desired camera number.

9 5. OPERATION 5.1. Operating the Camera The following camera operations can be performed when the Control indicator is on. [Operating keys] WIPER ZOOM TELE WIDE FOCUS FAR NEAR LENS SPEED UP DOWN RIGHT LEFT LOW HIGH DEF AUX AUTO AF POSITION CONTROL FREEZE FULL REMOTE CONTROLLER C-RM500 1 2 3 4 5 6 7...

Page 10 - M A N U A L; W I P E R; Lighting; A U X I L I A R Y S W

5.1.2. Rotating the camera with the joystick Any connected Combination camera can be rotated in the desired direction using a joystick. With the camera selected, tilt the joystick in the direction in which the camera is to be rotated.The camera will rotate in the direction the joystick was tilted. (...

Page 11 - Step 1. Press the Auto key while the camera; A U T O; Lights; LCD screen

5.1.6. Activating the automatic functions When a Combination camera is connected to the system, its automatic functions can be enabled using theAuto key. Step 1. Press the Auto key while the camera is selected. The camera's automaticfunctions (Auto-Pan* 1 , Auto Trace* 2 , or Preset Sequence* 3 ) wi...

Page 12 - A U T O F O C U S; Lightis; P O S I T I O N

5.1.11. Selecting the camera position Step 1. E n t e r t h e c a m e r a p o s i t i o n n u m b e r w i t h t h e numeric keypad. Step 2. Press the Position key. The camera image corresponding to the selectedposition will be displayed on the monitor. Note When the Trace function is used in the cam...

Page 13 - C H A N N E L C A L L

5.2.1. Displaying the camera number (only active when the Multi-Switcher is connected) Step 1. Press the Channel Call key while a camera image is displayed on the monitor.All connected camera numbers will be displayed. NoteThe camera number is displayed even when thecamera is not connected. [When co...

Page 14 - Press the Freeze Screen key.; Step 1. Enter the camera number to reset the; F R E E Z E; Note: Two lower screens can be freely; set using the switcher.

5.2.2. Viewing the freeze screen (only active when the Multi-Switcher is connected) Step 1. E n t e r t h e c a m e r a n u m b e r t o f r e e z e u s i n g t h e n u m e r i ckeypad. Step 2. Press the Freeze Screen key. The "F" indication will flash ont h e c o r r e s p o n d i n g c a m ...

Page 15 - Step 1. Enter the abbreviated number with the; F U N C T I O N K E Y; S E T

5.2.4. Using the abbreviated numbers By merely pressing the abbreviated number followed by the SET key, the camera image (camera number andposition number) programmed under the abbreviated number can be displayed on the monitor. (Refer to p. 38 "Abbreviation.") Step 1. Enter the abbreviated ...

Page 16 - Step 1. E n t e r t h e c a m e r a n u m b e r t o b e; C H A N N E L; 6 – S E G M E N T; Monitor screen

5.2.5. Viewing full-screen displays Step 1. E n t e r t h e c a m e r a n u m b e r t o b e displayed on the full screen using thenumeric keypad. Step 2. Press the Full Screen key. The designated camera image will bed i s p l a y e d o n t h e f u l l s c r e e n .Simultaneously, the Control indicat...

Page 17 - 0 – S E G M E N T; Camera name; – S E G M E N T; or; Camera number; Note: Camera images can be freely selected for; Screens XX and YY using the switcher.

[10-segment split-screen viewing] Step 1. Press the 10-Segment Split-Screen key. The images of camera numbers 1 – 8 (Group 1)and 2 more images (set with the Switcher) willbe displayed on the monitor. Step 2. Press the 10-Segment Split-Screen key again, or the Group Selector key. The images of camera...

Page 18 - Step 3. R e p e a t S t e p 2 t o d i s p l a y o t h e r; – S E G M E N T

[4-segment split-screen viewing] Step 1. Press the 4-Segment Split-Screen key. The images of camera numbers 1 – 4 (Group 1)will be displayed on the monitor. Step 2. Press the 4-Segment Split-Screen key again, or the Group Selector key. The images of camera numbers 5 – 8(Group 2) will be displayed on...

Page 19 - S E Q U E N C E; – S E G S E Q

5.2.7. Viewing sequential displays The outputs of all cameras connected to the switcher can be displayed on the monitor in sequential order atviewing intervals preset at the switcher. For details, refer to the instruction manual included with the switcher. [Sequential full-screen viewing] Press the ...

Page 20 - [When an alarm signal is received during Alarm Hold]; A L A R M H O L D; Flashes

20 5.3. Alarm Hold and Reset The Alarm can be held or reset when "1. KEY" has been selected in the "Alarm Hold" setting, and is notactivated when "2. ALWAYS" has been selected. (Refer to p. 36 "Alarm hold.") 5.3.1. Holding the alarm Press the Alarm Hold key.The Alarm ...

Page 21 - Setting Items and Their Descriptions

21 Operation mode* (Refer to p. 24) Designates the unit as a master or slave. Switcher* (Refer to p. 25) Determines the type of switcher to be connected to the unit. Contact point (Refer to p. 26) Sets the Alarm Contact Output Terminal's operation.(Only valid when "MASTER" has been selected ...

Page 22 - Used for entering numbers.; O P E R A T I O N M O D E

22 A B C D WIPER ZOOM TELE WIDE FOCUS FAR NEAR LENS SPEED UP DOWN RIGHT LEFT LOW HIGH DEF AUX AUTO E F G H SELECT MENU GROUP CH SEQUENCE FUNCTION ALARM RESET HOLD AF POSITION CONTROL FREEZE FULL REMOTE CONTROLLER C-RM500 1 2 3 4 5 6 7 8 9 C 0 SET Joystick Selects setting items when tilted up and dow...

Page 24 - Step 1. Press the Menu key to display the menu screen.; The setting contents will be displayed on Line 2.

24 6.4. Setting the Functions Perform the following settings referring to the Basic Setting Operations on p. 23. 6.4.1. Operation mode Sets the unit's operation mode. Step 1. Press the Menu key to display the menu screen. Step 2. Tilt the joystick up or down to select "OPERATION MODE," and c...

Page 25 - Test mode; Sets the type of switcher to be connected to the unit.; The setting contents will appear on Line 2.; S W I T C H E R; Camera alarm is unreceivable in this setting.

25 1. 16 INPUT* 1 Select this setting when the 16 channels Multi-Switcher is connected to theswitcher control terminal (RS-485).Select this setting when the system includes a switcher other than Multi-Switcheror Smart Switcher, and the number of control channels is 16 or less. 2. 9 INPUT A* 1 Select...

Page 26 - Sets the alarm contact output terminal's operation.; The setting content will appear on Line 2.; C O N T A C T

6.4.3. Contact Sets the alarm contact output terminal's operation. NoteContacts can only be set when "MASTER" has been selected in the "Operation mode" setting. This settingitem is not displayed on the menu screen if "SLAVE" has been selected. Step 1. Press the Menu key to di...

Page 27 - Disables the Automatic Reset function.; The setting will appear on Line 2.; A U T O R E T U R N

1. ON Confirming this setting displays the screen for setting the time interval before AutomaticReset occurs following camera operation. Tilt the joystick left or right to select the reset interval: "10 SEC," "15 SEC," "20 SEC," "30SEC," "1 MIN," "2 MIN,&#...

Page 28 - PAN; [Home position selector terminal operation settings]

6.4.5. Home position Sets the Combination camera to standby status when not being operated. NoteWhen "10. OTHER" is selected in the "Switchers" setting, set theoperation common to all channels. In this event, the screen describedin Step 2 below and the rightmost [ CH] indication on t...

Page 29 - I / O S P E E D C A M E R A; I / O S P E E D R E M O T E

6.4.6. I/O speed Sets each control terminal's transfer rate. Step 1. Press the Menu key to display the menu screen. Step 2. Tilt the joystick up or down to select "I/O SPEED" then press the SET key to confirm the selection.The screen for selecting the control terminal is displayed. Step 3. T...

Page 30 - B U Z Z E R

6.4.8. Initial screen Sets the screen to be displayed immediately after the power is turned on. Step 1. Press the Menu key to display the menu screen. Step 2. Tilt the joystick up or down to select "INITIAL SCREEN," then confirm the selection with the SET key. The setting will appear on Line...

Page 31 - Setting; I N I T I A L C H A N N E L

"Initial screen" Setting Setting 1. FULL Enter the channel to be designated with the numeric keypad, and confirmthe setting with the SET key. Note: This selection is set to "1" by the factory. 4. 4-SEG Tilt the joystick to the left or right to select "1 – 4," "5 – 8,"...

Page 32 - The setting is displayed on Line 2.; S E N S O R A L A R M; Does not use Sensor Alarm.

6.4.11. Camera alarm Select "1. ON" to use the Combination camera's alarm contact input. Step 1. Press the Menu key to display the menu screen. Step 2. Tilt the joystick up or down to select "CAMERA ALARM," and confirm the selection with the SET key. The setting is displayed on Line ...

Page 34 - P R E S E T C A M A L A R M

6.4.13. Camera alarm preset Sets the position number to automatically change the Combination camera's orientation when an alarm signalis received from the camera. NoteThis setting can only be performed when "1. ON" has been selected in the "Camera alarm" setting. Thissetting item is ...

Page 35 - Sets the interval between alarm input and alarm reset.; A L A R M S I G N A L; item) passes or when an alarm reset signal is received.

6.4.15. Alarm time Sets the interval between alarm input and alarm reset. NoteThe Alarm Time can only be set when "1. EDGE" has been selected in the "Alarm signal" setting. This settingitem is not displayed on the menu screen when "2. LEVEL" has been selected. Step 1. Press t...

Page 36 - A L A R M F U N C T I O N

6.4.17. Alarm hold Always places on hold alarm signals to the surveillance camera system. Step 1. Press the Menu key to display the menu screen. Step 2. Tilt the joystick up or down to select "ALARM HOLD," and confirm the selection with the SET key. The setting is displayed on Line 2. Step 3...

Page 40 - Sets the password required when opening the menu.; Step 1. Press the Menu key while holding down the Alarm Reset key.; The password setting screen will appear.; Press the Clear key to return to the setting item display.; C A M E R A M E N U

6.4.22. Password Sets the password required when opening the menu. Step 1. Press the Menu key while holding down the Alarm Reset key. The password setting screen will appear. Step 2. Enter the password (4 digits) with the numeric keypad, and confirm the password with the SET key. The display will re...

Page 41 - Note; Monitor TV

41 7. CONNECTIONS Note To eliminate noise, be sure to connect the shield of a shielded twisted-pair cable to be used for connectionbetween control terminals (for control) to the [GND] terminal. Equipment Which Can Be Controlled with the C-RM500 Shown below are equipment that can be controlled with t...

Page 43 - [Connected Camera Termination Switch Setting]; Termination switch ON

43 C-RM500 (Operation mode: "MASTER") Monitor TV Combination camera Camera control terminal GND Shielded twisted-pair cable Video output cable Camera control cable 1 A 2 B 3 A 4 B 5 Remote Controller C-RM500 Combination camera Combination camera Combination camera a b c a + b + c 1.2 km <...

Page 44 - input terminal number with the camera's address number.

44 7.3. Connection to the Multi-Switcher's RS-232C Terminal • When connecting the camera's video output cable to the Multi-Switcher, match the Multi-Switcher's camera input terminal number with the camera's address number. • The C-CC551 and C-CC554 Combination cameras permit settings of up to 255 ca...

Page 48 - Connection When Controlling the System from 2 Locations

7.5. Connection When Controlling the System from 2 Locations By connecting 2 C-RM500 Remote Controllers, the system can be controlled from 2 locations. Set the operation mode of one controller for "MASTER," and the other controller for "SLAVE." (Refer to p. 24"Operation mode"...

Page 49 - Alarm output / control input terminal

49 Alarm output / control input terminal 13 25 14 1 C-RM500 Pin No. Function Pin No. Function 1 Ground 14 Alarm Output 10 2 Alarm Output 1 15 Alarm Output 11 3 Alarm Output 2 16 Alarm Output 12 4 Alarm Output 3 17 Ground 5 Ground 18 Alarm Output 13 6 Alarm Output 4 19 Alarm Output 14 7 Alarm Output ...

Page 50 - Prepare the D-sub connector supplied with the Unit.; Step 1. S o l d e r t h e c a b l e w i r e s t o t h e; wrap with the copper foil tape.; Step 3. Cover the connector with shield

50 7.6.2. Assembling D-sub connectors onto cables Prepare the D-sub connector supplied with the Unit. Step 1. S o l d e r t h e c a b l e w i r e s t o t h e corresponding connector pins tobe used. Step 2. Bend back the braided shield and wrap with the copper foil tape. Step 3. Cover the connector w...

Page 51 - • Accessories

51 8. SPECIFICATIONS * Applies to the system where the unit and Combination camera are connected in a matched pair. Represents the total of connected cable distances if multiple Combination cameras or Interface units are connected inthe system (when the CPEV-S cable thicker than 0.65 mm in diameter ...