TOA C-CV44-3 NTSC - Manuals

Page 2 - TABLE OF CONTENTS; SAFETY PRECAUTIONS

2 TABLE OF CONTENTS 1. SAFETY PRECAUTIONS ................................................................................ 3 2. GENERAL DESCRIPTION ............................................................................. 4 3. HANDLING PRECAUTIONS ...................................................

Page 3 - • After reading, keep this manual handy for future reference.; Safety Symbol and Message Conventions; the user may be required to take adequate measures.; WARNING

3 1. SAFETY PRECAUTIONS • Before installation or use, be sure to carefully read all the instructions in this section in order to ensure long, trouble-free operation. • Be sure to follow all the precautionary instructions in this section, which contain important warnings regarding safety. • After rea...

Page 4 - condensation is formed.

4 2. GENERAL DESCRIPTION The TOA C-CV44-3 is an outdoor-use high-resolution camera equipped with a 1/4” CCD. Its water-resistantdesign permits it to be mounted to outdoor walls or ceilings with no need to protect it from rain and theelements. Because the camera angle can be freely moved, a wide rang...

Page 6 - Used in mounting example 3.; INSTALLATION AND CONNECTIONS

6 Camera mounting boltWasher-installed M8 x 14mm hex bolt(standard accessory) Security wire entry hole Bracket mounting bolt (M8 or W 3/8) 120º ø50 mm 12 mm 96 mm 97.6 mm 70 mm 76 mm 4 -ø6.5 mm ø10.5 mm Used in mounting examples 1 and 2. Used in mounting example 3. 5. INSTALLATION AND CONNECTIONS [C...

Page 7 - Note: If the bracket is only fixed at one place using

7 Up Down Female-thread anchorM8 or W 3/8 Ceiling Mounting bracket Plain washer Bracket mounting boltM8 or W 3/8 Spring washer Bracket mounting boltM8 or W 3/8 Female-thread anchorM8 or W 3/8 Ceiling Mounting bracket Anti-rotation screw(such as self-tapping screws) Plain washer Spring washer [Mounti...

Page 8 - Cable joint section; Connects to monitor; Attach the camera to the mounting bracket.

8 UL1095#22 Black/ White (Nonpolar) BNC jack Camera Input/Output terminal Cable joint section BNC plug Supplied cable Lock screw Connects to monitor Connector(water-resistant type) Water-resistant cap Connects to power supply source Insulation washers are attached to the mounting bracket. Mounting b...

Page 9 - Connect the camera to the monitor and power supply source.

9 Camera Input/Output terminal Monitor : BNC plug 24 V AC or 12 V DC Video output Use the external power supply unit of the following rating when the camera is operated on 12 V DC. 12 V DC, over 1.0 A Video input Fit the watertight cap (shaded section) securely to the camera. 5. Mount the water-resi...

Page 10 - Connect the Monitor output terminal to the monitor.

10 Loosen the two sunshade fixing screws. Pull out the sunshade after rotating. Turn the front cover in the direction indicated by the arrow to remove. Front cover 6. ADJUSTMENT 1. Detach the sunshade and front cover after completing camera mounting and connections. [Removing the sunshade] [Removing...

Page 11 - picture reproduction.

11 Mode setting switch Horizontal angle ± 60º Camera mounting bolt IRIS H L OFF ON BLC F. AD J SHUTTER 1/60 1/100 Vertical angle: 90º (In the case of ceiling mounting) Bracket mounting bolt Focus ring Zoom ring Iris control Picture tilting: ± 90º (Rotate the shaded section) Projection 5. Adjust the ...

Page 13 - ABOUT THE MODE SETTING SWITCH; Adjustment switch is set to ON.; Mode Setting Switch

13 OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON 7. ABOUT THE MODE SETTING SWITCH Set the Mode Setting switch for the best possible picture reproduction depending on installation conditions. 7.1. Adjustment Switch Set this switch when adjusting the lens focus. (Provides the same effect as when using the...

Page 15 - • Accessories

15 The specifications of this camera are subject to change without notice. • Accessories Mounting bracket ................................................................................ 1Cable with water-resistant cap (2 m) .................................................. 1Camera mounting bolt .....