Thomson TU-HDT104A - Manuals

Operating Instruction Book TU-HDT104A 5 2.2 Rear Panel • AC Power Mains : (100 - 250V~; 50/60 Hz), 1.0 A. • RF In : For connection to cable from outdoor terrestrial antenna. • RF Out : For connection to your TV antenna IN or VCR RF IN. • S-Video : Y/C component video for connection to TV. • CVBS : T...

Operating Instruction Book TU-HDT104A 6 … 3.2 Control Panel • : To turn your STB on/off (standby mode) • Number (0~9) keys: To select channels directly and other commands. • : To toggle between present and previous channels • : To enter the service navigating channel (Mosaic channel). Such a channel...

Operating Instruction Book TU-HDT104A 7 4 Installing Your Digital Receiver 4.1 Connecting Your Digital Receiver The following illustrations show some examples for connecting this HD Digital Receiver. Select the connection that is best suited for your needs. Many other connections may be possible whe...

Operating Instruction Book TU-HDT104A 8 Mode C (SD, TV/CVBS) Connect the CVBS composite video output socket on your digital receiver to your TV’s CVBS video input socket. Connect the S-Video (Y/C) component video output socket on your receiver to your TV’s S-Video input socket. (Refer to D) Note: Ca...

Operating Instruction Book TU-HDT104A 9 4.2 Output Mode Selection After you have connected the AV cables for video and audio between your digital receiver and the display device, check that the position of the output selection switch is correct for your chosen connection method as in the table below...

Operating Instruction Book TU-HDT104A 10 Mode B (HD, RGB) The switch on the rear of the digital receiver must be in position B, and the AV connections must be taken from the RGB HD15 socket. The digital receiver display will show “Hd r”. Press OK to confirm the selection, or switch to another mode. ...

Operating Instruction Book TU-HDT104A 11 Table 1: Output format table When all formats have been tested, a list of all accepted video formats will be displayed. You will have the option to accept this list or to start the procedure again. The accepted display formats are then displayed and you are r...

Operating Instruction Book TU-HDT104A 12 4.5 Select Aspect Ratio The first time the digital receiver is installed, or after Shipping Condition is restored (section 6.4), you will be asked to select your preferred aspect setting. This may be a choice of the Wide (16:9), Normal / Center Cut (4:3) or N...

Operating Instruction Book TU-HDT104A 13 5.2 Information Plate The Information Plate (I-Plate) shows information about the program that you are currently watching. The information plate appears briefly whenever you switch to a new channel or when there’s a problem with signal reception. To show the ...

Operating Instruction Book TU-HDT104A 14 5.4 Audio Selection The program you view may be accompanied by more than one audio soundtrack. These soundtracks may be of different languages or different types (Dolby D, MPEG-1 or MPEG-2). You may press the audio button to select your desired soundtrack. Wh...

Operating Instruction Book TU-HDT104A 15 6 Using the Main Menu Your receiver comes with a directory of features or the Main OSD. The Main is your gateway to customising many of the features offered by your receiver. To access the Main OSD, press the MENU button. The Main feature comprises the follow...

Operating Instruction Book TU-HDT104A 16 6.1 Program Guide Programs Schedule By choosing the Program Guide banner on the Main OSD, the Electronic Program Guide (EPG) appears. The EPG is, in classic terms, a TV Guide, except it is presented on your TV screen. The EPG allows you to peek in advance, de...

Operating Instruction Book TU-HDT104A 17 Category Selection This special feature enables you to screen out your preferred programs by program Category or type. You can gain access to this feature by pressing the button (yellow). Use the arrow buttons to highlight the categories, and press OK to sele...

Operating Instruction Book TU-HDT104A 18 6.2 TV/Radio Channels You may highlight any channel in the list by pressing up/down keys, then press OK to view that channel directly. This feature allows you to personalise your list of favourite channels, TV or Radio. Highlight a channel by using the S / T ...

Operating Instruction Book TU-HDT104A 19 VCR out This setting affects the video format at the VCR output, or the TV output when mode C (CVBS) is selected. If your display is 4:3 format and the transmission of a program happens to be 16:9, the Normal / Letterbox mode will give you a complete picture,...

Operating Instruction Book TU-HDT104A 20 Audio Language Priority From here you may prioritise languages for the audio output. To prioritise a language, press OK to highlight a language choice. Move the choice up or down by using the arrow buttons. Press OK again to confirm the priority. Note that th...

Operating Instruction Book TU-HDT104A 21 Digital Audio For each Audio Mode, you can have different Digital Audio Selection Options. (Refer to Table 2, Digital Audio Selection Table) Table 2: Digital Audio Selection Table Default Audio Mode Digital Audio Selection Options AC-3 1. Bitstream 2. PCM (st...

Operating Instruction Book TU-HDT104A 22 6.4 Advanced Settings In addition to the settings in “Preferences”, section 6.3, the Advanced Settings are used to program your digital receiver. Again, some of the settings, especially “Install” (3), may require assistance from your Service Provider. Your di...

Operating Instruction Book TU-HDT104A 24 6.5 Box Information From here, you can get general information about the Receiver ID, software and hardware version on which it is operating. 6.6 Software download Your digital receiver is capable of downloading new software being broadcast as part of a norma...

Operating Instruction Book TU-HDT104A 25 7 Glossary ‹ A/V: A connector for the transmission of audio, video and status signal. ‹ Information Plate: A small window with simple navigation tools to display information about individual channels. ‹ Menu: An onscreen display offering a list of commands to...

Operating Instruction Book TU-HDT104A 26 8 Troubleshooting Problem Possible causes What to do The display on the panel does not light up / is not lit Power Mains cable is not connected Check that the mains cable is plugged in to the power socket No sound or picture The A/V cord is not properly conne...

Operating Instruction Book TU-HDT104A 27 9 Technical Specifications Features Specifications Parameters Input frequency VHF, UHF Band Standard DVB-T (ETS 300 744) Channel Bandwidth 7MHz, Australian Channel COFDM System 2k, 8k carrier Hierarchical supported Demodulation type QPSK, 16QAM, 64QAM Guard I...

Operating Instruction Book TU-HDT104A 28 Serial port RS-232 (Female, DB-9) User interface Front panel 4 Keypads, 7-segment display and 3 LED indicators IR Sensor Mains input voltage 100-250VAC~ Mains input frequency 50/60 Hz Power requirements Power consumption Normal operation: 22Watt. Standby mode...

Operating Instruction Book TU-HDT104A 29 WARRANTY 1. The product is warranted for 12 months from the date of purchase. Subject to the conditions of this warranty Panasonic or its Authorised Service Centre will perform necessary service on the product without charge for parts or labour i f, in the op...