Thomson DPL680 - Manuals

Getting Started Inserting Batteries into Remote Control Install batteries as follows:1. Remove the battery compartment door by applying thumb pressure on battery door and then lift the door out and off the cabinet. 2. Insert 2 “AAA” (R03) batteries into the battery compartment according to the + and...

Getting Started Connecting to Audio-Visual Components 4 to LINE OUT (T ape Deck) to LINE IN ( T ape Deck ) R L CD IN IN OUT SAT IN DVD IN IN OUT TV IN DIGITAL S-VIDEO TAPE VCR L R AUDIO VIDEO OUT TO TV TV CD DVD SAT 1 2 CD DVD SAT COAXIAL DVD IN SAT IN OUT TO TV VIDEO AUDIO DIGITAL INPUTS Connect co...

Getting Started EN 5 Digital Connections Read instructions carefully when connectingcomponents to the receiver. Digital Input Jacks can accept Dolby Digital (AC-3) orPCM signals when compatible components areconnected. TV Connections TVs with RF input may need a RF modulator (notincluded) for inputt...

Getting Started Connecting the Speakers Speakers There are 6 speakers equipped with the unit (2 front, 1center, 2 rear, 1 subwoofer). In order to enjoy goodsurround effects, all six speakers need to be connected to the receiver. At least two front speakers (left and right) are required.For better so...

Getting Started Positioning your speaker 1 Left, Right (Front Speakers) They carry primarily music and sound effects 2 Center In surround mode, the center speaker carries much ofthe dialogue as well as music and effects. It should beset between the left and right speakers. 3 Surround (Rear Speakers)...

Getting Started Preferred surround placement Location If possible, place surround speakers to either side of thelistening area, not behind it. Height If space permits, install surrounds 60cm-90cm (2-3 feet)above viewers. This helps to minimize localizationeffects. Aiming Aiming surrounds straight ac...

Getting Started EN 9 Test Tone / Channel balance Channel balance Your receiver is equipped with a test signal generatorfor balancing the channels. As the signal "travels" fromchannel to channel, adjust the level controls until eachchannel plays at the same loudness level. To activate and adj...

H O M E T H E A T R E S Y S T E M ON/ECO PHONES PHONES VOLUME SOURCE SUBWOOFER PRESET SURROUND Operating Your Receiver 1. ON/ECO Turns the unit on and off. When the system is turned on, the unit will go to the mode it was in before powered off. 2. Display Displays current status of the receiver. 3. ...

Operating Your Receiver EN 11 Remote Control Please be sure you have inserted the batteries into the remotecontrol (see relevant section on page 3.) You can test it bypressing any button. 1. ON•OFF Turns the receiver and other Thomson auxiliary components onand off. (see page 14 “Using the Remote to...

Operating Your Receiver 12 Display DVD / VCR / SAT / TUNER / TAPE / CD / TV • An arrow points to the current source mode. • Dolby Digital audio input for signal format. • Dolby Pro Logic II audio output format. • DTS audio output format. FM / AM • Radio band indicator in Tuner mode. ST • Tuner stere...

Operating Your Receiver EN 13 Switching the unit on and off • To switch on the receiver, press the ON/ECO button on the main unit once, or the button on the remote control. • Standby: when the receiver is in tuner mode, press the ON/ECO button once to enter standby mode. On the remote control, press...

Operating your Receiver You can connect up to 6 audio/video sources to thisamplifier: Source button Corresponding connector (receiver front panel) (receiver back panel) - DVD DVD IN (audio / video) - VCR VCR IN/OUT (audio / video) - SAT SAT IN (audio / video) - CD CD IN (audio only) - TAPE TAPE IN/O...

Operating your Receiver EN 15 Using the receiver to play a source After having properly connected a source (DVD, CD,VCR) to the receiver, you can partly control themthrough the receiver. Playing a DVD with the receiver 1. Connect a DVD player to the receiver (see connecting your receiver for details...

Operating your Receiver Operating the Radio The receiver has a built-in tuner that allows for AM/FMradio function. Manual tuning 1. Connect the FM and AM antenna accordingly (see "Connecting the Antenna" on page 5 section for details) 2. Press ON/ECO on the main unit or on the remote control...

EN 17 Operating your Receiver Storing radio stations The receiver can store up to 40 radio stations inmemory. You can enter every single radio stationyourself or the receiver can store all available radiostations automatically in an ascending order. Auto Preset Programming (APP) : (FM only) 1. In Tu...

Operating your Receiver 18 RDS (Radio Data System) for FM Only The RDS icon shows on display when RDS data are received. The following information may be availableon certain stations:• Frequency station,• Station name, • Program type, • Clock,• Radio text Press RDS on the remote control repeatedly t...

EN 19 Advanced Sound Control Sound Enhancement Systems This receiver is equipped with several built-in soundenhancement systems. Dolby Digital The Dolby Digital mode lets you enjoy full digital surround from software processed in the DolbyDigital format. Dolby Digital provides better soundquality an...

20 Advanced Sound Control Dolby 3 Stereo The 3 Stereo mode will redirect the Surround signals to thefront left and right speakers when only the front and center speakers are used. . Stereo The Stereo mode uses the two main channel outputsfrom the front speakers. Use this mode if you haveconnected th...

EN 21 Advanced Sound Control Fine Setting of the Components The receiver can be directly turned on by pressing the DVD•6CH / SAT•CABLE / TV / CD•TAPE / VCR / TUNER buttons on the remote control, which also selects thebest surround sound mode. The default surround modesfor different components are li...

22 Advance Sound Control Fine Setting of the Speakers All the basic settings have already been pre-set for the speakers included in the box. Also, to make the surround sound more effective andsuit the acoustic conditions in your listening room, youmay need to delay the signal coming from some of the...

EN 23 Advance Sound Control Speaker Configurations You can also change the setup of the speakers.Use a subwoofer to enjoy optimum sound.• Speaker distance: For optimum surround experience measure the distance between the speaker and yourfavorite listening position. 1. Press the SETUP button to show ...

24 Troubleshooting Tips Troubleshooting Tips Receiver/Tuner Operation ST indicator is off. • Adjust the antenna.• Press GO BACK/ST.MONO button to insure you are not outputting in mono. The signal is Mono. Severe hum or noise. • The signal is too weak. Connect an external antenna.• Adjust Antenna• Re...

Care and Maintenance EN 25 Disconnect the audio system from the power source beforeperforming any maintenance. Cleaning Clean the exterior of the system using a soft dust cloth. Important battery information • Remove the batteries to avoid leakage if you do not use your remote control for more than ...