Thermo Pride OH65FA072D48B - Manuals

Page 2 - This furnace is not to be used as a construction heater.

i I. SAFETY SECTION This page contains various warnings and cautions found throughout the Oil Furnace Manual. Please read and comply with the statements below. c WARNING AND CAUTIONS: c WARNING: This furnace is not to be used as a construction heater. See Page 1. c CAUTION MUST BE TAKEN NOT TO EXCEE...

Page 3 - ii; TABLE OF CONTENTS

All installations and services must be performed by qualified service personnel. ii TABLE OF CONTENTS SECTION BEGINNING PAGE I. SAFETY SECTION i II. GENERAL INSTRUCTIONS 1 A. VENTING 2 B. DRAFT REGULATORS 3 C. DUCT WORK/AIR CONDITIONING 3 D. FILTERS MOUNTED EXTERNAL TO FURNACE 3 E. LIMIT POSITION AN...

Page 5 - Then, remove knock-out in side casing and extend; SIDE WALL VENTING APPLICATION ORDER INFORMATION; Beckett AFG

All installations and services must be performed by qualified service personnel. 2 A. VENTING: NOTE: On the OH6FA072D*** it is possible to rotate the flue elbow (which is factory installed for vertical discharge) 90° counterclockwise from the vertical position to adapt to various venting systems. c ...

Page 6 - specified otherwise by the individual coil manufacturer.; highboy

All installations and services must be performed by qualified service personnel. 3 B. DRAFT REGULATORS: A draft regulator is supplied with the furnace and should be installed according to the regulator manufacturers recommendations. With the burner operating, use a draft gauge to adjust the regulato...

Page 8 - DO NOT; remove this retainer when installing

All installations and services must be performed by qualified service personnel. 5 F. BURNER INSTALLATION: NOTICE: Remove all cardboard packing from around chamber before installing burner. The oil burner will mount on three stud mounting bolts on the lower mounting plate covering the opening in the...

Page 9 - G. BURNER SPECIFICATIONS AND APPLICATIONS; HEAD STATIC; OIL NOZZLE CAPACITY CHART; Beckett Riello

All installations and services must be performed by qualified service personnel. 6 G. BURNER SPECIFICATIONS AND APPLICATIONS FURNACE MODEL THERMO PRIDE’S BURNER SPEC NO. * INS BECKETT BURNER MODEL & TUBE LENGTH HEAD STATIC PLATE MAXIMUMNOZZLE SIZE** SHIPPED NOZZLE SIZE OIL PUMP PRESSURE (PSIG) O...

Page 10 - WARNING: THE HEAT EXCHANGER MUST BE CLEANED BY A QUALIFIED

All installations and services must be performed by qualified service personnel. 7 H. HEAT EXCHANGER CLEANING INSTRUCTIONS: c WARNING: THE HEAT EXCHANGER MUST BE CLEANED BY A QUALIFIED SERVICE PERSON. It is important to inspect and clean the heat exchanger once a year, or as necessary, to remove any...

Page 11 - EXTERIOR OF FURNACE:; discoloration of materials and damage from rust or corrosion.; CHIMNEY OR VENTING SYSTEM:; The furnace venting system should be inspected for signs of rust,

All installations and services must be performed by qualified service personnel. 8 III. USERS INFORMATION SECTION A. OIL SUPPLY: Do not allow the fuel tank to run completely empty. During the summer, keep the tank full to prevent condensation of moisture on the inside surface of the tank. If the fue...

Page 12 - Fig. 18: Location of the air filter on the typical highboy furnace.

All installations and services must be performed by qualified service personnel. 9 E. FILTER CLEANING AND LOCATION: The air filters should be inspected each month and cleaned when dirty. Cleaning the air filters frequently may reduce airborne contaminants from entering the furnace and depositing in ...

Page 13 - CUSTOMER; COMBUSTION

All installations and services must be performed by qualified service personnel. 10 COMBUSTION AND EFFICIENCY TESTING FOR THERMO PRIDE OIL FIRED CENTRAL FURNACES. Complete this form for each Thermo Pride furnace installed. Read instruction CUSTOMER NAME ADDRESS CITY, STATE HEATING SYSTEM BURNER MODE...