Taylor model 430 torque shake/slush freezer - Manuals

1 Model 430 Torque To the Installer 131202 Section 1 To the Installer The following information has been included in the manual as safety and regulatory guidelines. For complete installation instructions, please see the Installation Checklist. Installer Safety In all areas of the world, equipment sh...

3 Model 430 Torque To the Installer 130816 Beater Rotation Beater rotation must be clockwise as viewed looking into the freezing cylinder. Note: The following procedure must be performed by an authorized Taylor service technician. To correct rotation on a single- phase unit, change the leads inside ...

4 To the Operator Model 430 Torque 131202 Section 2 To the Operator The freezer you have purchased has been carefully engineered and manufactured to give you dependable operation. The Taylor Model 430 Torque, when properly operated and cared for, will produce a consistent quality product. Like all m...

10 Important: To the Operator Model 430 Torque Section 5 Important: To the Operator Viscosity Adjustment The viscosity (thickness) of the slush can be adjusted by turning the viscosity adjustment screw on the upper right side of the front panel. Turn the viscosity adjustment screw clockwise for a th...

11 Model 430 Torque Operating Procedures Section 6 Operating Procedures The Model 430 freezer is designed to produce shake or slush product at the desired thickness. This unit has a 4 quart freezing cylinder. We begin our instructions at the point where we enter the store in the morning and find the...

14 Operating Procedures Model 430 Torque 090114 Step 7 Install the front drip pan. Slide the long drip pan into the hole in the front panel. Figure 17 Step 8 Install the front drip tray and splash shield beneath the door spout. Figure 18 Step 9 Lay the air/mix feed tube (optional) in the bottom of t...

15 Model 430 Torque Operating Procedures 140804 Step 5 Place an empty pail beneath the door spout and move the draw handle to the right. Draw off all the sanitizing solution. When the sanitizer stops flowing from the door spout, move the draw handle to the left and place the control switch in the “O...

16 Operating Procedures Model 430 Torque 140804 Step 4 Place the mix hopper cover in position. Periodically, during the day’s operation, check to be sure there is a substantial amount of mix in the hopper. Figure 26 Closing Procedure To disassemble this unit, the following items will be needed: S Tw...

17 Model 430 Torque Operating Procedures 090114 Cleaning Step 1 Prepare a pail of an approved 100 PPM cleaning solution (examples: 2- 1/2 gal. [9.5 liters] of Kay- 5 R or 2 gal. [7.6 liters] of Stera- Sheen R ). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS. Step 2 Pour the cleaning so...

18 Important: Operator Checklist Model 430 Torque 071205 Section 7 Important: Operator Checklist During Cleaning and Sanitizing: ALWAYS FOLLOW LOCAL HEALTH CODES Cleaning and sanitizing schedules are governed by federal, state, or local regulatory agencies, and must be followed accordingly. If the u...

19 Model 430 Torque Important: Operator Checklist Winter Storage If the place of business is to be closed during the winter months, it is important to protect the freezer by following certain precautions, particularly if the building is to be left unheated and subject to freezing conditions. Disconn...

20 Troubleshooting Guide Model 430 Torque Section 8 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY PAGE REF. 1. No product being dispensed. a. Power switch is in the “OFF” position. a. Place power switch in the “AUTO” position. 15 b. Improper mixing of product. b. Carefully follow directions fo...

23 Model 430 Torque Limited Warranty on Equipment 131202 Section 10 Limited Warranty on Equipment TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor-branded freezer equi...

25 Model 430 Torque Limited Warranty on Parts 131202 Section 11 Limited Warranty on Parts TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor genuine replacem...