Taylor Model 161 - Manuals - manualsarea.com

Page 2 - Complete this page for quick reference when service is required:; Date of Installation:; Information found on the data label:; Voltage

Complete this page for quick reference when service is required: Taylor Distributor: Address: Phone: Service: Parts: Date of Installation: Information found on the data label: Model Number: Serial Number: Electrical Specs: Voltage Cycle Phase Maximum Fuse Size: A Minimum Wire Ampacity: A E August, 2...

Page 3 - Table of Contents

Table of Contents Model 161 Table of Contents Section 1 To the Installer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installer Safety 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Site P...

Page 4 - During Cleaning and Sanitizing

Model 161 Table of Contents Table of Contents -- Page 2 Section 7 Important: Operator Checklist 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . During Cleaning and Sanitizing 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting Bacterial...

Page 5 - Installer Safety

1 Model 161 To the Installer 081208 Section 1 To the Installer The following are general installation instructions. For complete installation details, please see the check out card. Installer Safety In all areas of the world, equipment should be installed in accordance with existing local codes. Ple...

Page 7 - Beater Rotation; Refrigerant

3 Model 161 To the Installer 120529 Electrical Hook-- Up Installation (60 Cycle, 1 Ph, Supplied With Cord and Plug) This freezer is supplied with a 3--wire cord and grounding type plug for connection to a single phase, 60 cycle, branch circuit supply. This unit must be plugged into a properly ground...

Page 8 - Section 2; Compressor Warranty Disclaimer

4 Model 161 To the Operator Section 2 To the Operator The Model 161 soft serve freezer has been carefully engineered and manufactured to give you dependable operation. This unit, when properly operated and cared for, will produce a consistent quality product. Like all mechanical products, it will re...

Page 11 - Section 4

7 Model 161 Operator Parts Identification Section 4 Operator Parts Identification Model 161 Figure 1 ITEM DESCRIPTION PART NO. 1 PAN-DRIP *161* 055206 2 PANEL -SIDE LEFT 058491 3 GASKET-HOPPER COVER 037042 4 COVER A.-HOPPER X37963-SER 4a KNOB-MIX COVER 025429 5 TUBE-FEED 030797 6 PANEL-REAR 058492 I...

Page 12 - Beater Door Assembly

8 Model 161 Operator Parts Identification 120501 Beater Door Assembly Figure 2 ITEM DESCRIPTION PART NO. 1 DRAW VALVE 024763 2 O-- RING 7/8 OD X .103 W 014402 3 SEAL-- VALVE 030930 4 KIT A.-- DOOR 3 SPT 1.5 QT X56906SER1 5 PIVOT PIN A.-- SHORT X38539 6 O-- RING 5/16 OD X .070 W 016272 7 DRAW VALVE H...

Page 13 - Accessories

9 Model 161 Operator Parts Identification 110727 Accessories Figure 3 ITEM DESCRIPTION PART NO. 1 PAIL-6·QT. 023348 2 BRUSH-REAR BRG 1” D X 2” LG 013071 3 BRUSH-DOUBLE·ENDED 013072 4 BRUSH-DRAW·VALVE·1” OD X2” X 17” 013073 ITEM DESCRIPTION PART NO. 5 BRUSH-MIX·PUMP·BODY-3”X7”WHITE 023316 6 LUBRICANT...

Page 14 - Section 5; Symbol Definitions

10 Model 161 Important: To the Operator Section 5 Important: To the Operator Figure 4 ITEM DESCRIPTION 1 POWER SWITCH 2 MIX REFRIGERATION KEY 3 STANDBY KEY 4 WASH KEY 5 AUTO KEY 6 INDICATOR LIGHT “MIX LOW” 7 RESET BUTTON Symbol Definitions To better communicate in the International arena, the words ...

Page 16 - Feed Tube

12 Model 161 Important: To the Operator If the beater motor is turning properly, press the WASH key to cancel the cycle. Press the AUTO key on both sides of the unit to resume normal operation. If the freezer shuts down again, contact a service technician. Feed Tube The feed tube serves two purposes...

Page 17 - Section 6; Assembly

13 Model 161 Operating Procedures 120529 Section 6 Operating Procedures The Model 161 is a soft serve counter model with a three spout door. Two individual flavors are available from the end spouts, and an equal combination of both is dispensed through the center spout to create a twist effect. It h...

Page 20 - Sanitizing

16 Model 161 Operating Procedures Step 13 Snap the design caps over the bottom of the freezer door spouts. Figure 17 Step 14 Lay the feed tubes in the bottom of the mix hoppers. Step 15 Install the front drip tray and splash shield under the freezer door. Figure 18 Step 16 Install the drip pans. Fig...

Page 25 - Troubleshooting Bacterial Count

21 Model 161 Important: Operator Checklist Section 7 Important: Operator Checklist During Cleaning and Sanitizing ALWAYS FOLLOW LOCAL HEALTH CODES. Cleaning and sanitizing schedules are governed by federal, state, or local regulatory agencies, and must be followed accordingly. If the unit has a “Sta...

Page 26 - Winter Storage

22 Model 161 Important: Operator Checklist j 5. If your machine is air cooled, check the condenser for an accumulation of dirt and lint. A dirty condenser will reduce the efficiency and capacity of the machine. Condensers should be cleaned monthly with a soft brush. Never use screwdrivers or other m...

Page 27 - Section 8; PROBLEM

23 Model 161 Troubleshooting Guide Section 8 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY PAGE REF. 1. No product being dispensed. a. The power switch is in the OFF position. a. Place the power switch in the AUTO position. 17 b. The mix level is inadequate in the mix hopper. b. Fill the mix h...

Page 30 - Section 9

26 Model 161 Parts Replacement Schedule 120501 Section 9 Parts Replacement Schedule PART DESCRIPTION EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY QTY. Beater Drive Shaft Cup Seal X 2 Freezer Door O--Ring X 2 Freezer Door Front Bearing X 2 Freezer Door Guide Bearing X 2 Draw Valve O--Ring X 4 Center Draw V...