Taylor 428 - Manuals

1 Model 428 To the Installer 131206 Section 1 To the Installer The following information has been included in the manual as safety and regulatory guidelines. For complete installation instructions, please see the Installation Checklist. Installer Safety In all areas of the world, equipment should be...

2 Model 428 To the Installer 080828 Electrical Connections This equipment is supplied with a 3-wire cord and grounding type plug, for connection to a single phase, 60 cycle, branch circuit supply. This unit must be plugged into a properly grounded receptacle. The cord and plug provided are 20 A for ...

3 Model 428 To the Installer 130923 Appliances that are permanently connected to fixed wiring and for which leakage currents may exceed 10 mA, particularly when disconnected or not used for long periods, or during initial installation, shall have protective devices such as a GFI, to protect against ...

4 Model 428 To the Operator 131206 Section 2 To the Operator The freezer you have purchased has been carefully engineered and manufactured to give you dependable operation. The Taylor Model 428, when properly operated and cared for, will produce a consistent quality product. Like all mechanical prod...

7 Model 428 Operator Parts Identification 101101 Section 4 Operator Parts Identification Model 428 Figure 1 ITEM DESCRIPTION PART NO. 1 LENS-LIGHT 052952 2 PLATE A.-DEC LIGHTED X52936 3 FILTER-AIR-17 X 13 X 7/16 052951 4 PANEL A.-SIDE*LEFT X62592 5 COVER A.-HOPPER X51152 6 TUBE-FEED 5/16 HOLE SS 028...

8 Model 428 Operator Parts Identification 120614 Beater Door Assembly With Standard Door (No Prime Plug) Figure 2

10 Model 428 Operator Parts Identification 120614 Beater Door Assembly With Self- Closing/Prime Plug Door Figure 3

11 Model 428 Operator Parts Identification 120614 Beater Door Assembly With Self - Closing/Prime Plug Door ITEM DESCRIPTION PART NO. 1 CAP A.- SPRING- RETAINER X54755 2 SPRING- COMP.970X.082X3.875 030344 3 PLUNGER- CAP DRAW SWITCH 080554 4 PIN- HANDLE- VALVE 064864 5 VALVE- DRAW- SLUSH 080662 6 O- R...

12 Model 428 Operator Parts Identification 140718 Accessories Figure 4 ITEM DESCRIPTION PART NO. 1 KIT A.-TUNE UP X50413 2 BRUSH-MIX PUMP BODY-3”X7” 023316 3 BRUSH-DOUBLE ENDED 013072 4 BRUSH-REAR BRG 1IN.DX2IN 013071 5 BRUSH-DRAW VALVE 1X2X17 013073 ITEM DESCRIPTION PART NO. 6 BRUSH- SYRUP PORT 045...

13 Model 428 Important: To the Operator 081002 Section 5 Important: To the Operator Figure 5 ITEM DESCRIPTION PART NO. 1 SWITCH- ROCKER AUTO/ WASH (POWER SWITCH) 048420 2 SWITCH- TOGGLE- SPST 3/4 HP/250V (DISPLAY LIGHT) 012626 3 BUSHING A.- TORQUE (VISCOSITY ADJUSTMENT) X50399- SER 4 LIGHT- AMBER- R...

15 Model 428 Operating Procedures Section 6 Operating Procedures The Model 428 freezer is designed to produce shake or slush product at the desired thickness. This unit has a 7 quart freezing cylinder. We begin our instructions at the point where we enter the store in the morning and find the parts ...

17 Model 428 Operating Procedures 120418 Step 7 Insert the torque rotor end with the guide bearing into the pilot hole in the center of the drive shaft. The hole in the torque rotor shaft should be rotated to the 12 o’clock position. Figure 14 Freezer Door Assembly - Standard Door (No Prime Plug) No...

18 Model 428 Operating Procedures Step 12 With the ice buster in place, rotate the draw valve to allow installation of the draw handle. This will lock the ice buster in place. Install the draw handle pin, and close the draw valve by moving the handle to the left. Figure 19 Step 13 Place the large ru...

22 Model 428 Operating Procedures 140718 Sanitizing Step 1 Prepare a 2- 1/2 gallon (9.5 liter) pail of cleaning/sanitizing solution with an active chlorine concentrate of 100 - 200 PPM (parts per million). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS. Step 2 Pour the sanitizing soluti...

23 Model 428 Operating Procedures 050415 Priming the Freezing Cylinder Step 1 With a pail beneath the door spout, move the draw handle to the right. Pour two gallons (7.6 liters) of FRESH mix into the hopper and allow it to flow into the freezing cylinder. This will force out any remaining sanitizin...

24 Model 428 Operating Procedures 140718 Step 5 Place the mix hopper cover in position. For proper operation, there must be a substantial amount of mix in the hopper. If the ADD MIX light illuminates, refill the mix hopper as soon as possible. Figure 44 Closing Procedure To disassemble this unit, th...

25 Model 428 Operating Procedures 080428 Rinsing Step 1 Pour two gallons (7.6 liters) of cool, clean water into the mix hopper. With the brushes provided, scrub the mix hopper, float switch, and the mix inlet hole. Figure 45 Step 2 With a pail beneath the door spout, place the power switch in the WA...

26 Model 428 Operating Procedures 080313 Disassembly BE SURE THE POWER SWITCH IS IN THE OFF POSITION. Failure to follow this instruction may result in severe personal injury from hazardous moving parts. Step 1 Remove the torque arm, handscrews, freezer door, torque rotor, beater assembly, scraper bl...

27 Model 428 Important: Operator Checklist 051207 Section 7 Important: Operator Checklist During Cleaning and Sanitizing: ALWAYS FOLLOW LOCAL HEALTH CODES Cleaning and sanitizing schedules are governed by federal, state, or local regulatory agencies, and must be followed accordingly. If the unit has...

28 Model 428 Important: Operator Checklist Winter Storage If the place of business is to be closed during the winter months, it is important to protect the freezer by following certain precautions, particularly if the building is to be left unheated and subject to freezing conditions. Disconnect the...

29 Model 428 Troubleshooting Guide Section 8 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY PAGE REF. 1. No product being dispensed. a. Power switch is in the OFF position. a. Place power switch in the AUTO position. 23 b. Improper mixing of product. b. Carefully follow directions for mixing pr...

31 Model 428 Parts Replacement Schedule Section 9 Parts Replacement Schedule PART DESCRIPTION EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY QUANTITIES TO BE REPLACED Drive Shaft Seal X 1 Drive Shaft O-Ring X 1 Scraper Blade X 1 Freezer Door Gasket X 1 Front Bearing X 1 Draw Valve O-Rings X 2 Black Bristle ...

34 Model 428 Limited Warranty on Parts 131206 Section 11 Limited Warranty on Parts TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor genuine replacement com...

36 Model 428 Limited Warranty on Parts LIMITATION OF WARRANTY THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER...