Taylor 371 - Manuals - manualsarea.com

Page 3 - ENGLISH; TABLE OF CONTENTS

Models 369/370/371 3 ENGLISH Note: Continuing research results in steady improvemenets; therefore, information in this manual is subjectto change without notice. This dispenser is manufactured under one or more of the following U.S.patents and/or other pending patents:U.S.A. 4,900,158U.S.A. 4,696,41...

Page 4 - bearing in; figure 1; IMPORTANT

4 Models 369/370/371 1 TECHNICAL CHARACTERISTICS The electric diagram of the dispenser is located insideinner part of the dispensing side panel. Specifications are subject to change without notice. 2 INTRODUCTION Please read all sections of this manual thoroughly to familiarizeyourself with all aspe...

Page 5 - TO OPERATE SAFELY; figure 2

Models 369/370/371 5 ENGLISH 4 TO OPERATE SAFELY 1 - Do not operate the dispenser without reading this operator’s manual. 2 - Do not operate the dispenser unless it is properly grounded. 3 - Do not use extension cords to connect the dispenser. 4 - Do not operate the dispenser unless all panels are r...

Page 6 - OPERATION HELPFUL HINTS; Granita viscosity adjustment; figure 4; Beverage temperature adjustment:; figure 5; CLEANING AND SANITIZING; ATTENTION

6 Models 369/370/371 Safety pressure switch warning light (C) To operate the unit:1 - Set the power switch to I position.2 - Set the mixer/refrigeration switches as follows: - to the I position to get soft drink.- to the II position to get Granita. 3 - Set the light switch to I position. 5. 2 OPERAT...

Page 7 - figure 6; - Remove the bowl by lifting its faucet side up and off the; figure 7; - Slide the outer spiral out (see figure 9) and then the inside; figure 9

Models 369/370/371 7 ENGLISH side up and off the hook located on the opposite side (seefigure 6). figure 6 3 - Remove the bowl by lifting its faucet side up and off the fastening hooks (see figure 7) and slide it out (see figure8). figure 7 figure 8 4 - Slide the outer spiral out (see figure 9) and ...

Page 9 - ROUTINE MAINTENANCE

Models 369/370/371 9 ENGLISH (see figure 12) 4 - Fit bowl gasket around its seat. Note: the largest brim of gasket must face against the rearwall (see figure 14). figure 14 5 - Carefully insert the auger into the evaporator use caution to prevent it from hitting the rear wall (see figure 15). figure...

Page 10 - Never rotate the timer counterclockwise

10 Models 369/370/371 from the condenser filter. Remove the only left panel (from faucet side) unscrewingthe two plastic coated screws (see figure 18). figure 18 3 - Replacement of lighted top cover bulb: remove the screw placed in the upper part of the top cover, remove the lower part and replace t...

Page 11 - - Program the defrost timer by pushing out on the tabs C

Models 369/370/371 11 ENGLISH time of day with the arrow B on the timer face. This is a 24hour timer showing both A.M. and P.M. 2 - Program the defrost timer by pushing out on the tabs C that correspond to the hours desired to defrost. Each tabrepresents 15 minutes. A minimum of four to eight hoursa...

Page 12 - OPERATOR PARTS IDENTIFICATION

OPERATOR PARTS IDENTIFICATION MODEL 369/370/371 2471_01 V 3.5 04I09

Page 14 - GEAR MOTOR

GEAR MOTOR 052213-12052213-27052213-34052213-44 Motor-Gear *369,370,371* GEN 3(Magnetic Drive - BR 0067955/Up) Include: 1 052042 Bracket-Gear Motor w/Bushing 8 052047 Cap-Ball Bearing 19 052052 Gasket-Gear Motor 2 057900 Stator-Gear Motor (230V / 50Hz) 9 057878 O-Ring-Gearshaft 20 052053 Cover-Gear ...