Taylor 047772-M - Manuals

4 Model PH90 To the Operator 081210 Section 2 To the Operator The freezer you have purchased has been carefully engineered and manufactured to give you dependable operation. The Taylor Model PH90, when properly operated and cared for, will produce a consistent quality product. Like all mechanical pr...

7 Model PH90 Operator Parts Identification Section 4 Operator Parts Identification

8 Model PH90 Operator Parts Identification PH90 Exploded View Parts Identification ITEM DESCRIPTION PART NO. 1 COVER A.-HOPPER X42628-SER 1a KNOB-MIX COVER 025429 1b RETAINER-HOPPER COVER 042619 1c SCREW-8-32 X 1/2 OVAL HD 043295 2 AGITATOR X44797 3 PAN-DRIP HEAT TREAT 048204 4 PANEL-REAR 048208 5 L...

13 Model PH90 Operator Parts Identification Syrup Tank ITEM DESCRIPTION PART NO. 1 SYRUP TANK (4 QT./3.8 LITER) 045533 1a SYRUP TANK COVER 035759-- 1 *1b TIP-- NYLON-- WHITE 042747 TIP-- NYLON-- GREY 024261 1c GASKET-- SYRUP TANK COVER 016037 1d DIP TUBE 015441-- 7 1d-- 1 O-- RING-- DIP TUBE 018550 ...

14 Model PH90 Operator Parts Identification Accessories ITEM DESCRIPTION PART NO. 1 SANITIZER KAY-5 (125 PACKS) 041082 2 LUBRICANT-TAYLOR HI-PERF. 048232 3 KIT - TUNE UP X49463-12 4 PAIL-MIX 10 QT. 013163 5 BRUSH-SET LVB 050103 6 BRUSH-REAR BRG 1 IN.DX2 IN 013071 7 BRUSH-DOUBLE ENDED 013072 ITEM DES...

15 Model PH90 Important: To the Operator Section 5 Important: To the Operator ITEM DESCRIPTION 1 Power Switch (Toggle) 2 Indicator Lights (PCB A.--LED) 3 Flavor Selector Keypad (Switch--Membrane) 4 Liquid Crystal Display 5 Keypads (Switch--Membrane) 6 Heater Switches (Toggle) Symbol Definitions To b...

17 Model PH90 Important: To the Operator Adjustable Draw Handle The soft serve side of the freezer features an adjustable draw handle to provide the best portion control, giving a better, consistent quality to your product and controlling costs. The draw handle should be adjusted to provide a flow r...

20 Model PH90 Important: To the Operator If the WASH keypad is pressed, the next display will appear and the freezer will have to be disassembled and brush cleaned. OFF :MODE: OFF OK :MIX: OK 41.0F HOPPER 41.0F FREEZER LOCKED Once the freezer is unlocked by starting a heat treatment cycle, only the ...

23 Model PH90 Operating Procedures Section 6 Operating Procedures Equipment Set Up Evaluate the condition of lights and screen messages (Hard Lock or Soft Lock, etc.) before performing opening procedures. If all four LED’s on the front of the unit are lit, the unit is locked. (See Figure 1.) Figure ...

27 Model PH90 Operating Procedures Insert the spinner blade shaft from the bottom, into the center of the driven spinner, and up through the draw valve cavity until the shaft appears at the top of the draw valve. The spinner blade must be aligned and engaged to the driven spinner at the bottom. This...

31 Model PH90 Operating Procedures Install the two notched drip pans in the left and right side panels. (See Figure 35.) Figure 35 Step 8 Install the front drip tray and splash shield under the door spouts. (See Figure 36.) Figure 36 Mix Hopper Assembly To assemble the mix hopper for both sides of t...

40 Model PH90 Operating Procedures 080221 Priming -- Soft Serve Side Step 1 With a mix pail beneath the door spout, open the draw valve. Pour 2--1/2 gallons (9.5 liters) of FRESH mix into the mix hopper and allow it to flow into the freezing cylinder. This will force out any remaining sanitizing sol...

44 Model PH90 Operating Procedures 080221 CAUTION: Do not draw product during the heating cycle because of high product temperatures. When the heating cycle is complete, the control will return to the STANDBY mode. There are 3 phases of the heat cycle: Heating, Holding and Cooling. Each phase has a ...

47 Model PH90 Operating Procedures Step 3 When ready to resume normal operation, press the AUTO keypad. (See Figure 84.) Note: This procedure should be done 15 minutes before product is expected to be served. Figure 84 Syrup System Two main objectives in your opening procedures must be to: (1) fill ...

50 Model PH90 Operating Procedures Attach the syrup lines to the freezer door. Insert the syrup line fitting into the syrup port in the freezer door. The flat side of the syrup line fitting must be aligned with the pin in the syrup port. Rotate the syrup line fitting upward to lock in place. (See Fi...

52 Model PH90 Operating Procedures Step 14 Remove the discharge tube from the valve body. (See Figure 106.) Figure 106 Step 15 Remove the 1--5/16” o--ring from the valve body, and remove the 1” o--ring from the discharge tube. Cleaning the Syrup Pump Step 1 Flush and rinse the pump in a container of...

53 Model PH90 Operating Procedures Step 8 Insert the brush, by the non--bristle end, into the passageway between the inlet valve and the outlet valve. (See Figure 110.) Figure 110 Step 9 Move the brush back and forth to scrub this passageway. Advance the brush completely, and pull the brush out of t...

55 Model PH90 Operating Procedures Step 12 Install the cylinder onto the larger opening in the valve body by tilting the cylinder away from the discharge tube and sliding the widest section of flange under the center locking groove on the valve body. Align the tabs on the cylinder with the locking g...

56 Model PH90 Operating Procedures Step 5 With a pail under the door spout, press the WASH and PUMP keypads. Open the draw valve and start to drain the product from the freezing cylinder and mix hopper. (See Figure 121.) Figure 121 Step 6 When the flow of product stops, press the WASH and PUMP keypa...

57 Model PH90 Operating Procedures 081210 Step 3 Open the draw valve on the freezer door. Drain all the rinse water from the door spout, close the draw valve, and press the WASH keypad, cancelling the wash cycle. Step 4 Repeat this procedure using clean, warm water, until the water being discharged ...

59 Model PH90 Operating Procedures 080221 Remove the two small o--rings and one large o--ring from the drive shaft. Step 7 Remove the front drip tray and splash shield. Remove the ladles from the two cold topping containers. Step 8 Remove the long drip pan from the front panel, the two short drip pa...

60 Model PH90 Operating Procedures 080221 Using small double end brush, brush clean the syrup line fittings. Step 6 Prepare a sink with an approved 100 PPM sanitizing solution (example: Kay--5 R or Stera--Sheen R ). USE WARM WATER AND FOLLOW THE MANUFACTUR- ER’S SPECIFICATIONS. Repeat Step 5 with th...

61 Model PH90 Important: Operator Checklist Section 7 Important: Operator Checklist During Cleaning and Sanitizing ALWAYS FOLLOW LOCAL HEALTH CODES. Cleaning and sanitizing schedules are governed by your State or local regulatory agencies and must be followed accordingly. The following check points ...

62 Model PH90 Important: Operator Checklist 080221 Winter Storage If the place of business is to be closed during the winter months, it is important to protect the freezer by following certain precautions, particularly if the building is to be left unheated and subject to freezing conditions.Disconn...

75 Model PH90 Parts Replacement Schedule Section 9 Parts Replacement Schedule PART DESCRIPTION EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY Scraper Blade--Shake X Scraper Blade--Soft Serve X Drive Shaft Seal X Freezer Door O--Ring--Shake X Freezer Door Gasket--Soft Serve X Front Bearing X Beater Front Sho...