Tannoy V12HP - Manuals - manualsarea.com

Page 3 - Declaration of Conformity

CONTENTS 1. Introduction 2. Unpacking 3. Connectors/Cabling 4. Polarity Checking 5. Amplification & Power Handling 6. Crossovers 7. Equalisation 8. Arraying 9. Dimensions 10. Performance Data 11. Technical Specifications 12. Rigging & Suspension 12.1 General Safety Advice 12.2 Secur – ET VMY...

Page 4 - Passive Full Range

1. Introduction The Tannoy V12HP utilises a high performance Dual Concentric ™ drive unit – the 12” (300mm) PowerDual ™ . The substantially increased efficiency and power handling of this all-new driver design ensures that the V12HP is capable of delivering high SPL’s in even the most demanding appl...

Page 5 - Polarity Checking

Cable choice consists mainly of selecting the correct cross sectional area in relation to the cable length and the load impedance. A small cross sectional area would increase the cables series resistance, inducing power loss and response variations (damping factor). Connectors should be wired with a...

Page 10 - Technical Specifications

11. Technical Specifications Frequency Response (1) +/- 3dB 67Hz - 23kHz 55Hz - 25kHz (with Tx2/TDx2 controller) -10dB Point 57Hz (50Hz with Tx2/TDx2 controller) Recommended Amplifier Power (passive Full Range) 350 - 700 watt / 8 ohm Power Handling(2) Average(2) Programme Peak (10ms) Passive Full Ra...

Page 16 - VCS; Description Quantity

12.5 SECUR – ET VTH Pole Mount 12.6 SECUR – ET VCS Ceiling Saddle 12.7 SECUR – ET VPC Pole Clamp The Tannoy V12HP loudspeaker is fitted as standard with a blanking plate on the base of the cabinet. However, should you ever wish to mount the V12HP onto a standard 35mm pole mount this blanking plate c...

Page 18 - PEQ 1 may also be omitted when using the V12HP as a floor monitor.

13.2 Passive System Parameters (optional) With the vast array of digital loudspeaker management systems available it is inevitable that the user may opt to use a controller other than the TX2 & TDX2 as part of a large scale integrated system. In passive mode the V12HP has been designed to need n...

Page 19 - Note : When using the V12HP with subs, set HPF on LF section @ 80 – 110Hz

13.3 Biamp System Parameters Parameter Unit/Name Low Section High Section Gain (dB) 0 -1.0 Delay (ms) 0.167 0 Polarity Positive Positive HPF Ä Freq (Hz) 42.5 1680 Slope (dB/oct) 24 24 Filter Shape Butterworth Linkwitz Riley LPF Freq (Hz) 1470 Thru Slope (dB/oct) 24 NA Filter Shape Linkwitz Riley NA ...

Page 20 - DO NOT SHIP ANY PRODUCT TO TANNOY WITHOUT PREVIOUS AUTHORISATION

14. V12HP Service Parts & Accessories Part Number Description 7900 0715 Driver Kit - 3190 7900 0716 Recone Kit – 3190 7900 0717 HF Driver 7900 0718 HF Diaphragm Kit 7300 0905 Crossover 8001 2780 VMY – Secur ET – Yoke Adjustable (Black) 8001 2790 VMY – Secur ET – Yoke Adjustable (White) 8001 2800...

Page 21 - Declaration of Conformity

The following apparatus is/are manufactured in the United Kingdom by Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to Domestic Electrical Equipment....

Page 22 - Tannoy North America; Is

Tannoy United Kingdom T: +44 (0) 1236 420199 F: +44 (0) 1236 428230 E: [email protected] Tannoy North America T: (519) 745 1158 F: (519) 745 2364 E: [email protected] Tannoy adopts a policy of continuous improvement and product specification is subject to change. 648 1 040 3 Is sue 1.0 G H A...