Stiga 1381 HST - Manuals - manualsarea.com

Page 3 - Man; HST

3 G L M Man ÁÁÁ ÁÁÁ ÁÁÁ Á Á K J 1 2 3 4 5 7 M L HST 4 6 8 5 7 9

Page 8 - ENGLISH; SYMBOLS; Use hearing protection.; SAFETY INSTRUCTIONS; GENERAL; Disengage all controls before starting the engine.; OPERATION

59 ENGLISH EN 1 SYMBOLS The following symbols appear on the machine. They are there to remind you of the care and attention required in use. This is what the symbols mean: Warning. Read and understand the owner’s manual before using this machine. Remove the key, disconnect the spark plug wire, and c...

Page 9 - MAINTENANCE AND STORAGE; ASSEMBLY; CONTENTS - OUTER PACKING

60 ENGLISH EN • Never drive across a slope. Move from the top down, and from the bottom to the top. Be careful when changing direction on a slope. Avoid steep slopes. • Never operate the machine with insufficient protection or without the safety devices in place. • Existing safety devices must not b...

Page 10 - GEAR LEVER/SPEED LEVER; CONTROLS; ELECTRIC CABLE – ELECTRICAL START

61 ENGLISH EN 3.7 GEAR LEVER/SPEED LEVER Manual, see fig. 6.HST, see fig. 7.1. Set the lever in a suitable position to simply fit the angle link (L) into the hole in the gearbox lever (M). 2. Assemble the washer and the lock nut.3. Tighten the nut. 3.8 CHECKING THE CONTROL WIRES The control wires mi...

Page 11 - USING THE SNOW THROWER

62 ENGLISH EN 4.18 SHOES (13) Used to set the height of the auger housing above the ground. 4.19 WHEEL LOCK 4.19.1 HST See fig. 8. Machines with hydrostat are equipped with easily disengaged wheel locks. This is essential when mowing the machine without the motor running. Disengage/engage the wheel ...

Page 12 - STARTING THE ENGINE (WITH ELECTRICAL

63 ENGLISH EN 5.5 STARTING THE ENGINE (WITH ELECTRICAL START) Do not touch engine components because they are warm during use. Risk of burn injuries.Never run the machine indoors. The exhaust fumes contain carbon monoxide, a very toxic gas. 1. Attach the connecting cable to an earthed extension lead...

Page 13 - MAINTENANCE; Service item

64 ENGLISH EN 5.9 AFTER USE 1. Check for loose or damaged parts. If required, change damaged parts. 2. Tighten loose screws and nuts.3. Brush all the snow from the machine.4. Move all the controls backwards and forwards a few times. 5. Put the choke in position 6. Disconnecting the starting cable fr...

Page 14 - If the pinion gear is too tight against the ring gear, move; SERVICE AND REPAIRS; TROUBLESHOOTING

65 ENGLISH EN 6.6.4 Chute worm gear See fig. 13.If the discharge chute is difficult to operate, first lubricate the pinion gear (B) and ring gear (A). If it is still difficult to operate, adjust as follows:1. Loosen the nut (C), which holds the pinion gear bracket in the slotted hole. 2. If the pini...

Page 15 - THE AUGER BELT; Check and adjustment of the auger belt

66 ENGLISH EN 7.4 THE AUGER BELT 7.4.1 Replacing the auger belt Man, see fig. 18, 19.HST, see fig. 20, 21.1. Remove the ignition key.2. Loosen the screws (3) and dismantle the bottom plate (2). See fig. 16. 3. Remove the belt protective cover (1) by loosening the screws (2). See fig. 16. 4. Loosen t...

Page 16 - ADJUSTING THE CONTROL WIRES

67 ENGLISH EN 7.7 ADJUSTING THE CONTROL WIRES When the belts are adjusted or replaced, the control wires must also be checked/adjusted (see below). 7.7.1 Adjusting auger wire 1. Remove the ignition key.2. Dismantle the belt cover (1) by loosing the screw (2). See fig. 16. 3. Actuate the auger drive ...

Page 17 - STORAGE

68 ENGLISH EN 7.11 HEADLAMP BULB Only 27 W original spare part bulb is allowed to be used. Bulbs with higher power will damage the headlamp. The headlamp bulb is fitted to the headlamp by a bayonet socket. See fig. 17. To replace the bulb proceed as follows:1. Turn the bulb about 30° CCW and pull it...

Page 18 - G G P S w e d e n A B

w w w . s t i g a . c o m G G P S w e d e n A B · B o x 1 0 0 6 · S E - 5 7 3 2 8 T R A N Å S