StarTech.com SV565UTPUSA - Manuals

Page 3 - Table of Contents

Instruction Manual i Table of Contents Introduction ............................................................................................ 1 Packaging Contents ................................................................................................................................. 1Sys...

Page 4 - Introduction; Packaging Contents

Instruction Manual 1 Introduction The SV565UTPUSA USB VGA KVM Console Extender w/ Serial & Audio over Cat5 UTP (1000 ft) lets you control a server, workstation or multiple computers (connected through a KVM Switch) over standard Cat5 or Cat6 UTP Ethernet cable, at distances of up to 1000ft (333m...

Page 5 - Installation; Front View

Instruction Manual 2 Installation Front View Transmitter Unit 1. DE-15 VGA In (male)2. 3.5mm mini-jack audio In3. 3.5mm mini-jack microphone Out4. USB type B host connector5. DB9 RS-232 serial (female) Receiver Unit 1. DE-15 VGA Out (female)2. 3.5mm mini-jack audio Out3. 3.5mm mini-jack microphone I...

Page 6 - Rear View

Instruction Manual 3 Rear View Transmitter Unit 1. DC Power connector2. RJ45 Link connector3. 3.5mm mini-jack Audio Out4. DE-15 VGA Out (female) Receiver Unit 1. DC Power connector2. Setup button3. RJ45 Link Out connector4. RJ45 Link In connector 1 2 3 4 1 2 3 4

Page 7 - Hardware Installation; Driver Installation

Instruction Manual 4 Hardware Installation Transmitter Unit 1. Connect the included USB cable between the computer/KVM and the USB port on the Transmitter Unit. This also provides power to the Transmitter Unit. Optional: A 5V DC power adapter can be used for backup or if not using the USB cable. Thi...

Page 8 - Configuration; Serial Data Link; Automatic Calibration Button and Light

Instruction Manual 5 Configuration Serial Data Link The SV565UTPUSA/SV565USAGB is able to link two RS232 ports together to allow touchscreens, monitor control ports and other devices to be used remotely. The port’s baud rate is detected automatically and supports 300 to 19200 bps, with 9600 being th...

Page 9 - Commands

Instruction Manual 6 times because it depends on timing. To exit the menu press X to return to data transfer mode. Commands are case sensitive.The Transmitter Unit is able to access all of the Receiver units attached to it, allowing changes to be made from a central location. Also the Transmitter Un...

Page 10 - Image Quality; Firmware Upgrade

Instruction Manual 7 blurriness and streaking artifacts, then it is set too low. Increase it gradually until it becomes sharp and free of streaking. If it is too high then there will be problems with color patterns and noise appearing due to the high frequency components of the signal.Skew is used t...

Page 11 - Troubleshooting

Instruction Manual 8 Afterwards the key will need to be re-formatted to return to normal use.To upgrade all the Receiver units and the Transmitter Unit, plug the USB key into the first Receiver Unit of the chain. If it is plugged into another Receiver Unit it will only upgrade itself. This can be us...

Page 13 - Specifications

Instruction Manual 10 Specifications Connectors (Transmitter Unit) 1 x DE-15 VGA female 1 x DE-15 VGA male 1 x DB9 serial female 1 x USB type B female 3 x 3.5mm Audio mini-jack 1 x RJ45 Ethernet female Connectors (Receiver Unit) 1 x DE-15 VGA female 1 x DB9 serial male 2 x USB type A female 2 x 3.5m...

Page 14 - Technical Support

Instruction Manual 11 Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation...