Stamina 15-7250 - Manuals

EQUIPMENT WARNING & NOTICE LABELS This chart is provided to help identify the warning & notice labels on the Magnetic Fusion 7250 Bike. Please take a moment to familiarize yourself with all of the warning & notice labels. Label is larger than actual size WARNING LABEL(109) W1 5

H A RDWA R E I D E N T I F I C AT I O N C H A RT This chart is provided to help identify the hardware used in the assembly process. Place the washers or theends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check thelength of the bolts and screws. NO...

ASSEMBLY INSTRUCTIONS 7 Place all parts from the box in a cleared area and position them on the floor in front of you. Remove allpacking materials from your area and place them back into the box. Do not dispose of the packing materialsuntil assembly is completed. Read each step carefully before begi...

8 ASSEMBLY INSTRUCTIONS STEP 3 Attach the REAR STABILIZER(6) to the REAR FRAME(5) with BUTTON HEAD BOLTS(M8x1.25x53mm) (72), LOCK WASHERS(M8)(100), and WASHERS(M8)(103). STEP 4 Slide the FOOT CAPS(63) onto both ends of the REAR STABILIZER(6) so they fit over the edges of the LEFT and RIGHT REAR COVE...

9 ASSEMBLY INSTRUCTIONS To attach the HANDRAIL(9), position the HANDRAIL(9) under the SEAT CARRIAGE(7) as shown in the above illustration and secure with BUTTON HEAD BOLTS(M8x1.25x45mm)(71), ARC WASHERS(M8) (98), and LOCK WASHERS(M8)(100). STEP 8 Refer to the inset drawing. Plug the PULSE SENSOR WIR...

10 ASSEMBLY INSTRUCTIONS STEP 9 Attach the SEAT(59) and BACK CUSHION(60) to the SEAT FRAME(8) with ROUND HEAD BOLTS (M6x1x38mm)(82). STEP 10 Refer to the inset drawing. Press the NUT CAPS(M10)(53) onto the NYLOCK NUTS(M10x1.5)(95) on both sides of the SEAT CARRIAGE(7).

12 ASSEMBLY INSTRUCTIONS Socket of Power Wire(28) A. B. STEP 13 Refer to illustration A. Run the CONNECTION WIRE(26) through the hole in the plate on the HANDLEBAR(4). Attach the HANDLEBAR(4) to the UPRIGHT(3) with BUTTON HEAD BOLT(M8x1.25x40mm)(70) and FLAT HEAD SCREWS(M6x1x12mm)(78). STEP 14 Plug ...

13 SET UP INSTRUCTIONS Place the Magnetic Fusion 7250 Bike in the area where it will be used. It is recommended that the Magnetic Fusion 7250 Bike be placed on an equipment mat. The Magnetic Fusion 7250 Bike is approximately 55 3/4 inches long x 24 3/8 inches wide x 50 3/8 inches tall (max.). (These...

14 OPERATIONAL INSTRUCTIONS SEAT ADJUSTMENT LOAD ADJUSTMENT CAUTION: 1.2. Rotate the ADJUSTMENT KNOB(49) counterclockwise until the pin releases when the knob is pulled. Pull the ADJUSTMENT KNOB(49) and slide the SEAT CARRIAGE(7) up or down to desired position. Lock the SEAT CARRIAGE(7) in position ...

COMPUTER INSTRUCTIONS Your Magnetic Fusion 7250 Bike utilizes a magnetic braking system to create resistance for your workout. You control the amount and pattern of this resistance by means of the advanced computer console mountedat the center of the handlebar. We recommend that you use this compute...

16 COMPUTER INSTRUCTIONS LCD DISPLAY INSTRUCTIONS Displays the selected program during exercise, from P1 to P12. Displays the time. Counts upward from one second to 99:59 minutes. Counts down frompreset value. Displays the current speed from zero to 99.9 miles per hour. Displays the distance from ze...

17 COMPUTER INSTRUCTIONS PROGRAM DESCRIPTIONS (P1) MANUAL PRESET PROGRAMS: P2 to P10 are preset automatic programs. The profiles are shown on the face of the computer. Use the " " button to increase the load level of the program. Use the " " button to decrease the load level of the p...

COMPUTER INSTRUCTIONS (P11) 60% MAX H.R. (P12) 85% MAX H.R. 18 As you exercise, the program will monitor your pulseand adjust the workload automatically to keep youworking within a zone that is plus or minus 5 beats perminute of your target heart rate. Your age and theprogram you selected will deter...

COMPUTER INSTRUCTIONS STEP 1: POWER ON Pedaling or press any button. COMPUTER OPERATION STEP 2 : SELECT PROGRAM Select and press one of the PROGRAM BUTTONS to enter the desired program. STEP 3: SET THE PROGRAM TIME OR CALORIE (and input age for Heart Rate Control Programs) The TIME function mode wil...

20 STORAGE 1.2. 3. To store the Magnetic Fusion 7250 Bike, simply keep it in a clean dry place. Adjust the SEAT CARRIAGE(7) to the lowest position. The Magnetic Fusion 7250 Bike is approximately 55 3/4 inches long x 24 3/8 inches wide x 50 3/8 inches tall (max.). These dimensions will vary. Pleaseme...

CONDITIONING GUIDELINES How you begin your exercise program depends on your physical condition. If you have been inactive forseveral years or are severely overweight, start slowly and increase your workout time gradually. Increaseyour workout intensity gradually by monitoring your heart rate while y...

WARM-UP and COOL-DOWN Warm-Up The purpose of warming up is to prepare your body for exercise and to minimize injuries. Warm up for two to five minutes before strength training or aerobic exercising. Perform activities that raiseyour heart rate and warm the working muscles. Activities may include bri...

WARRANTY LIMITED WARRANTY MODEL 15-7250 Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanshipunder normal use, service and proper operation for a period of 90 days on the parts and five years on theframe from the date of the original purchase from a...

25 1 Front Frame 1 2 Front Stabilizer 1 3 Upright 1 4 Handlebar 1 5 Rear Frame 1 6 Rear Stabilizer 1 7 Seat Carriage 1 8 Seat Frame 1 9 Handrail 1 10 Pulley and Axle 1 11 Bearing (6003Z) 2 12 Bearing Washer (M17) 2 13 C Ring (17mm) 2 14 V-Ribbed Belt 1 15 Idler Arm 1 16 Idler Wheel 1 17 Idler Wheel ...

IMPORTANT : Before filling out the form below make sure you have the right information. Refer to the parts list to make sure you're ordering the right parts! Detach and Mail or Fax the Form Below Stamina Products, Inc. P.O. Box 1071 Springfield, MO 65801-1071 IMPORTANT : We must have your phone numb...