Spalding M88724C1 - Manuals

Page 2 - WARNING; SAFETY INSTRUCTIONS; REQUIRED TOOLS AND MATERIALS:

2 ID# M88724C1 08/06 Owner must ensure that all players know and follow these rules for safe operation of the system. WARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. • During play, especially when performing dunk type activities, keep player's f...

Page 3 - PARTS LIST

Item Qty. Part No. Description 1 1 968880 Pole 2 1 908266 Tube, 8x8, Ground Anchor, Black 3 1 Rim Assembly 4 1 Net 5 4 203017 Nut, Hex, 3/8-16 6 4 203300 Washer, 3/8 Locking, .380 I.D., .63 O.D. 7 4 200512 Bolt, Hex, 3/8-16 x 3.5” Long 8 1 204922 Pin, Hitch 9 1 204923 Pin, Cotter, #8 10 3 204993 Reb...

Page 4 - HARDWARE IDENTIFIER (OTHER—NOT ACTUAL SIZE)

4 ID# M88724C1 08/06 Item #5 (4) Item #34 (4) Item #24 (9) Item #7 (4) Item #28 (3) Item #20 (1) Item #23 (1)* Item #25 (8) Item #26 (1) Item #22 (9)* Item #8 (1) Item #9 (1) HARDWARE IDENTIFIER (NUTS, WASHERS & SPACERS) HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #27 (1) Item #19 (26) HARDWAR...

Page 5 - Ensure ground is level with playing surface, then dig pole hole.

5 08/06 ID# M88724C1 Ensure ground is level with playing surface, then dig pole hole. CONTACT UTILITIESBEFORE DIGGING. WARNING! 24" (61 cm) 48" (121.9 cm) PLAYING SURFACE GROUND SURFACE 24" (61 cm) 48" (121.9 cm) 1. 2. Install nuts (25) onto the ground tube bolts as shown. Nuts on th...

Page 6 - SIDE VIEW

6 ID# M88724C1 08/06 1" (2.54 cm) SIDE VIEW DRAINAGE HILL PLAYING SURFACE Fill hole with concrete. Tamp down concrete to release air pocketsand build drainage hill. 3. Insert rebar (10) through holes in ground tube assembly (2) as shown. 4. 10 10 10 2

Page 7 - NOTE ORIENTATION

7 08/06 ID# M88724C1 IMPORTANT!: WAIT A MINIMUM OF 72 HOURS BEFORE GOING ON TO NEXT STEP. CONCRETE MUST CURE. ALLOW ADDITIONAL TIME FOR COLD, WET OR HUMID WEATHER. IMPORTANT! Check leveling of mounting plate several times with carpenter’s level while concrete is curing. 24 24 24 24 Insert ground tub...

Page 10 - people are required to lift pole into; THIRD; While pole is being supported by; TWO; Completed Assembly; FIGURE

10 ID# M88724C1 08/06 THREE CAPABLE ADULTSREQUIRED FOR THISPROCEDURE. FAILURETO FOLLOW THISWARNING COULD RESULTIN SERIOUS INJURYAND/OR PROPERTYDAMAGE. WARNING! 8. TWO people are required to lift pole into position so that the threaded assemblyrod (14) can be installed and secured bythe THIRD person....

Page 15 - Rim Assembly

15 08/06 ID# M88724C1 13. 5 7 Refer To Instructions Included With Rim Hardware For Rim Assembly. Before starting rim assembly, tighten nut (26) until it is positioned 6-3/4” from the end of the rod (14) asshown (Figure A). Remove rim cover (16), attach rim assembly (3) to backboard (13) and reattach...

Page 16 - Set-up For Right Side

16 ID# M88724C1 08/06 14. A. B. 15. Apply height indicatorlabels (32 & 31) to heightindicators (30). 2. 4. 3. 1. Install net (4) to rim as shown. 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9 10 IMPORTANT! NOTE ORIENTATION OF HEIGHT INDICATORS: 10’ MARK SHOULD FACE AWAY FROM BACKBOARD. Set-up For Ri...

Page 20 - LIMITED LIFETIME WARRANTY; What is Not Covered By This Warranty; RIM

20 ID# M88724C1 08/06 LIMITED LIFETIME WARRANTY Subject to proper installation and normal use, Spalding ® warrants, subject to limitations below, to the original retail purchaser all structural components of the Spalding ® system to be free of defects in material and workmanship for the duration of ...