Spalding M8872411 - Manuals

Page 2 - WARNING; SAFETY INSTRUCTIONS; REQUIRED TOOLS AND MATERIALS:

2 ID# M887241 1 09/05 IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL Owner must ensure that all players know and follow these rules for safe operation of the system. WARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. • Dur...

Page 3 - PARTS LIST

Item Qty. Part No. Description 1 1 968880 Pole 2 1 998880 Plate, Anchor, Black 3 1 Rim Assembly 4 1 Net 5 4 203017 Nut, Hex, 3/8-16 6 4 203300 Washer, 3/8 Locking, .380 I.D., .63 O.D. 7 2 250001 Bolt, Hex, Tap, 3/8-16 x 4” Long 8 2* 250002 Bolt, Hex, Tap, 3/8-16 x 2” Long 9 1 203457 Label, Logo, Vin...

Page 4 - HARDWARE IDENTIFIER (OTHER—NOT ACTUAL SIZE)

4 ID# M887241 1 09/05 Item #5 (4) Item #13 (2) Item #34 (4) Item #24 (9) Item #7 (2) Item #8 (2)* Item #29 (4) Item #28 (3) Item #20 (1) Item #23 (1)* Item #25 (12) Item #26 (1) Item #22 (9*) Item #36 (1) Item #37 (1) HARDWARE IDENTIFIER (NUTS, WASHERS & SPACERS) HARDWARE IDENTIFIER (BOLTS &...

Page 5 - Ensure ground is level with playing surface, then dig pole hole.

5 09/05 ID# M887241 1 Ensure ground is level with playing surface, then dig pole hole. Install threaded ends of J-bolts (19) through holesin mounting plate (2) and secure as shown. 2 25 25 25 19 19 Install nut (25) to J-bolt (19) asshown. Repeat procedure forremaining three J-bolts (19). 2.75” (7 cm...

Page 6 - SIDE VIEW; WAIT A MINIMUM OF 72 HOURS BEFORE GOING ON

6 ID# M887241 1 09/05 Insert J-bolts (19) from mounting plate (2) into cement as shown. Move assembly around to releaseany air pockets in cement, then rest mounting plate on cement drainage hill. Apply some pressure tolevel mounting plate on top of drainage hill. Level mounting plate and square with...

Page 9 - people are required to lift pole into; THIRD; While pole is being supported by; TWO; AY; FIGURE

9 09/05 ID# M887241 1 THREE PEOPLEREQUIRED FOR THISPROCEDURE. FAILURETO FOLLOW THISWARNING COULD RESULTIN SERIOUS INJURYAND/OR PROPERTYDAMAGE. WARNING! 8. TWO people are required to lift pole into position so that the threaded assemblyrod (14) can be installed and secured bythe THIRD person. While p...

Page 14 - Rim Assembly

14 ID# M887241 1 09/05 13. 5 8 Refer To Instructions Included With Rim Hardware For Rim Assembly. Before starting rim assembly, tighten nut (26) until it is positioned 6-3/4” fromthe end of the rod (14) as shown (Figure A). Remove rim cover (16), attach rim assembly (3) to backboard (10) andreattach...

Page 15 - Set-up For Right Side

15 09/05 ID# M887241 1 14. A. B. 15. Apply height indicatorlabels (32 & 31) to heightindicators (30). 2. 4. 3. 1. Install net (4) to rim as shown. 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9 10 7 8 910 7 8 910 7 8 9 10 7 8 9 10 7 8 9 1...

Page 19 - LIMITED LIFETIME WARRANTY; What is Not Covered By This Warranty; RIM

19 09/05 ID# M887241 1 LIMITED LIFETIME WARRANTY Subject to proper installation and normal use, Hydra-Rib ® warrants, subject to limitations below, to the original retail purchaser all structural components of the Hydra-Rib ® system to be free of defects in material and workmanship for the duration ...