Spalding M88604C1 - Manuals

Page 2 - WARNING; REQUIRED TOOLS AND MATERIALS:

2 ID# M88604C1 08/06 Owner must ensure that all players know and follow these rules for safe operation of the system. WARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. • During play, especially when performing dunk type activities, keep player's f...

Page 3 - PARTS LIST

3 08/06 ID# M88604C1 Item Qty. Part No. Description 1 1 968880 Pole 2 1 908266 Tube, Ground Anchor, Black 3 1 Rim Assembly 4 1 Net 5 4 205702 Nut, Hex, 3/8-16 6 4 203300 Washer, Locking, 3/8 7 4 205700 Bolt, Hex, 3/8-16 x 3.5” Long 8 1 204922 Pin, Hitch 9 1 204923 Pin, Cotter, #8 10 3 204993 Rebar, ...

Page 5 - Ensure ground is level with playing surface, then dig pole hole.

5 08/06 ID# M88604C1 Ensure ground is level with playing surface, then dig pole hole. CONTACT UTILITIESBEFORE DIGGING. WARNING! 24" (61 cm) 48" (121.9 cm) PLAYING SURFACE GROUND SURFACE 24" (61 cm) 48" (121.9 cm) 1. Install nuts (25) onto the ground tube bolts as shown. Nuts on the t...

Page 6 - SIDE VIEW

6 ID# M88604C1 08/06 1" (2.54 cm) SIDE VIEW DRAINAGE HILL PLAYING SURFACE Fill hole with concrete. Tamp down concrete to release air pocketsand build drainage hill. 3. Insert rebar (10) through holes in ground tube assembly (2) as shown. 4. 10 10 10 2

Page 7 - NOTE ORIENTATION

7 08/06 ID# M88604C1 IMPORTANT!: WAIT A MINIMUM OF 72 HOURS BEFORE GOING ON TO NEXT STEP. CONCRETE MUST CURE. ALLOW ADDITIONAL TIME FOR COLD, WET OR HUMID WEATHER. IMPORTANT! Check leveling of mounting plate several times with carpenter’s level while concrete is curing. 24 24 24 24 Insert ground tub...

Page 10 - Completed Assembly; people are required to lift pole into; THIRD; While pole is being supported by; TWO; FIGURE

10 ID# M88604C1 08/06 8. 26 24 15 9 8 14 Completed Assembly TWO people are required to lift pole into position so that the threaded assemblyrod (14) can be installed and secured bythe THIRD person. While pole is being supported by TWO capable adults, position rod (14) and lockinto place with hitch p...

Page 15 - Rim Assembly

15 08/06 ID# M88604C1 13. 5 7 Refer To Instructions Included With Rim Hardware For Rim Assembly. 3 Rim Assembly 6 13 7 IMPORTANT! Carefully cut and peelprotective film away fromboard prior to attaching rim. Before starting rim assembly, tighten nut (26) until it is positioned 6-3/4” fromthe end of t...

Page 16 - Set-up For Right Side

16 ID# M88604C1 08/06 14. A. 15. Apply height indicatorlabels (32 & 31) to heightindicators (30). 2. 4. 3. 1. Install net (4) to rim as shown. 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9 10 Set-up For Right Side Set-up For Left Side 32 31 30 30 B. Attach height indicators to lower yoke in area shown by tur...

Page 20 - What is Not Covered By This Warranty; RIM; LIMITED LIFETIME WARRANTY

20 ID# M88604C1 08/06 Subject to proper installation and normal use, Spalding ® warrants, subject to limitations below, to the original retail purchaser all structural components of the Spalding ® system to be free of defects in material and workmanship for the duration of ownership by the original ...