Spalding M881111 - Manuals

12/05 ID# M881111 9 SECTION A: ASSEMBLE THE POLE This is what your system will look like whenyou’ve finished this section: TOOLS REQUIRED FOR THIS SECTION Shovel and Post Hole Digger Carpenter's Level CONCRETE Container to Mix Phillips-Head Screwdriver

10 ID# M881111 12/05 XG08.EPS205334 18" (42.7 cm) 6" (15.2 cm) 24" (61 cm) PLAYING SURFACE GROUND SURFACE 2. Ensure ground is level with playing surface, then dig pole hole. 1. Correctly identify each pole section. 1 2 3 MIDDLE BOTTOM TOP Identification Sticker Identification Sticker IMP...

12/05 ID# M881111 11 3. Snap two halves of ground sleeve (4) together. Insert andsecure bottom pole section (3) into ground sleeve (4) bytightening ground sleeve cap (5). 3 5 4 4 4 Flared end goes insideground sleeve. NOTE: 4. Fill hole approximately 1/3 full with mixed concrete.

12 ID# M881111 12/05 1" (2.54 cm) 1" (2.54 cm) 1" (2.54 cm) SIDE VIEW FIG. A FLANGE Insert ground sleeve assembly and center in hole ( FIG. A ). 5. IMPORTANT! CONTINUE ON TO NEXT STEP. DO NOT WAIT FOR CONCRETE TO CURE. PLAYING SURFACE Leave 1" below flange exposedfor drainage hill. N...

12/05 ID# M881111 13 4 3 Fill hole completely with concrete. 6. 1" (2.54 cm) 1" (2.54 cm) 1" (2.54 cm) 5 GSLV09.EPS 211121 1" (2.54 cm) 7. Tamp down concrete to release air pockets and build drainage hill. Level pole section in alldirections several times while concrete is curing. 1&...

14 ID# M881111 12/05 After concrete has cured, remove bottom pole section from ground sleeve (4). Place anti-skid tape (36) around the bottom area of bottom pole (see note A). 4 8. 5 36 Place top edge of anti- skid tape on mark made in step 7, NOTE A. NOTE A: Tape prevents the pole from rotating dur...

12/05 ID# M881111 15 9. Stack and bounce bottom (3) and middle (2) pole sections together. Bounce pole sectionstogether until middle section no longer moves toward taped reference mark on bottom pole. 2 3 Wood Scrap (NOT SUPPLIED) Identification Sticker KEEP GROUND SLEEVECAP ON BOTTOM POLE. IMPORTAN...

18 ID# M881111 12/05 12 6 12 13 13 11 9 10 10 12. 6 8 14 14 17 15 13. Attach spacers (12, 13) to pole mount bracket (6) with bolts (9), washers(10), and nuts (11) as shown. Assemble lanyard (17) to locking pin (16) as shown. Attach covers(14) onto pole mount bracket (6) with carriage bolt (15) and n...

20 ID# M881111 12/05 SECTION B: ASSEMBLE THE ELEVATOR TUBES TO BACKBOARD This is what your system will look like whenyou’ve finished this section. 9/16” 3/4” 1/2” (2) 1/2”, (2) 9/16”, and 2 3/4” Wrenches (2) Socket Wrenches and Sockets TOOLS REQUIRED FOR THIS SECTION AND/OR 1 . 30 Upper Elevator tub...

12/05 ID# M881111 21 Attach backboard support brackets (25) to the backboard frame using bolts (31) and nuts (10) as shown. 1 . 25 11 25 31 11 31 IMPORTANT! IMPORTANT! DO NOT TIGHTEN HARDWARE COMPLETELY. IMPORTANT! NOTE ORIENTATION. 25

26 ID# M881111 12/05 3. 43 46 45 42 Install Slam Jam Rim to Backboard 44 42 45 46 B C D E A • Fit rim (32) securely into bracket (41) as shown (Allow "T"-bolt (42) to slip through center hole in rim (32). B • Install reinforcement bracket (43) onto “T” bolt (42) as shown. C • Install spring ...

30 ID# M881111 12/05 SECTION D: UPRIGHT, SECURE AND USE POLE SYSTEM This is what your system will look like when you’ve finished thissection. Wedge Hammer TOOLS REQUIRED FOR THIS SECTION

12/05 ID# M881111 31 5 2. 1. Use wedge to tap cap of ground sleeve until tight. 4 10ft (3.05 m) 26 After concrete has cured, remove tape, install pole cap (26), fit pole assembly into sleeve (4). DO NOT USE THE BACKBOARD OR RIM TOMOVE POLE ASSEMBLY INTO POSITION. THEBACKBOARD AND RIM ARE NOT LOCKED ...

32 ID# M881111 12/05 4. 16 B. A. C. 3. A. While holding handle, remove pin (16). B. Move elevator up or down to desired height. C. Replace pin (16) full length to lock system at desired height. Apply height adjustment label (35) to front ofpole as shown. Regulation rim height is 10 feet (3.05 m). 10...