Spalding M7900412 - Manuals

Page 2 - WARNING; SAFETY INSTRUCTIONS; Remove all contents from boxes.; NOTICE TO ASSEMBLERS; inspect for loose small parts.

2 ID# M7900412 05/06 Owner must ensure that all players know and follow these rules for safe operation of the system. WARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. • During play, especially when performing dunk type activities, keep player's f...

Page 3 - PARTS LIST - See Hardware Identifier; Description

3 05/06 ID# M7900412 PARTS LIST - See Hardware Identifier HARDWARE IDENTIFIER (BOLTS) Item Qty. Part No. Description 1 1 Rim 2 2 20260401 Bolt, Carriage 3/8 x 4.75” Long 3 2 203474 Washer, Flat, 1”O.D. 4 2 203017 Hex Nut, 3/8” 5 4 203063 Nylon Nut, 3/8” 6 8 203232 Washer, 3/4” O.D. 7 2 200484 Spring...

Page 4 - HARDWARE IDENTIFIER; LOGO

4 ID# M7900412 05/06 HARDWARE IDENTIFIER (NUTS, WASHERS & SPACERS) HARDWARE IDENTIFIER (Not Actual Size) #31 (1) #27 (1) #18 (1) #13 (1) #14 (1) #15 (1) LOGO #19 (1) #22 (2) #28 (1) Item #30 (2) #7 (2) #1 (1) #5 (4) #17 (6) #4 (2) #10 (2) #24 (2) #26 (2) #25 (2) #3 (2) #6 (8) #23 (2) #8 (2)

Page 5 - TOOLS REQUIRED; ASSEMBLE THE BACKBOARD AND RIM

5 05/06 ID# M7900412 TOOLS REQUIRED 1/2" 9/16" 3/4" 1/2" 9/16" 3/4" AND/OR This is what your system will look likewhen you’ve finished this section: ASSEMBLE THE BACKBOARD AND RIM WARNING! IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGET...

Page 6 - We recommend mounting backboard to a solid

6 ID# M7900412 05/06 Attach foam pad (22) to bothfront and back of backboard sothat holes on pad line up withholes on backboard as shown.Attach foam (28) to H-Frame(27) as shown. 22 TWO CAPABLE ADULTSREQUIRED FOR THISPROCEDURE. FAILURETO FOLLOW THISWARNING COULDRESULT IN SERIOUSINJURY AND/ORPROPERTY...

Page 8 - RIM ASSEMBLY & INSTALLATION; NOTE: COMPLETED ASSEMBLY

8 ID# M7900412 05/06 Place a special locking nut (25) approximately half-way up on each carriage bolt (2) as shown.Keep the two special locking nuts (25) at the same level. NOTE: COMPLETED ASSEMBLY 2 25 4. RIM ASSEMBLY & INSTALLATION 1 3 2 24 4 Install two carriage bolts (2) through rim (1), was...

Page 9 - be flush on both sides of; Line up holes

9 05/06 ID# M7900412 1 13 25 Then, insert spacer (10) through back bracket (13), nylon washers (23) and rim assembly (1). BOTTOM VIEW 13 10 Spacer flush with bracket BOTTOM VIEW 13 23 23 10 1 Ends of spacer (10) should be flush on both sides of board bracket (13). NOTE: Line up holes 23 23 Spacer fl...

Page 11 - Align these

11 05/06 ID# M7900412 Position rim assembly (1) 90 degrees to back bracket (13) as shown. Place inner-bracket (14)over both carriage bolts (2) followed by springs (7), washers (8) and special nuts (26). NOTE: COMPLETED ASSEMBLY Tighten special nuts (26) until flush with end of carriage bolts (2) as ...

Page 12 - BOTTOM VIEW

12 ID# M7900412 05/06 First, test fit spacer (10) into back bracket (13) and Carefully rock in a circular motion to ream outany excess paint from holes if necessary. Insert spacer (10) through bottom holes in board bracket(13) and inner bracket (14). BOTTOM VIEW 13 10 13 10 Ends of spacer (10) shoul...

Page 14 - OUTSIDE VIEW

14 ID# M7900412 05/06 Secure net (18) to rim (1). 1 2 3 4 1 OUTSIDE VIEW Apply logo label (19) to cover plate (15). Install cover plate (15) on rim (1) using self tappingscrews (12) as shown (note orientation of cover plate). 12 15 19 15 Cover plate (15)will fit INSIDEback bracket. NOTE: 15 15 14. 1...