Spalding 211948C - Manuals

Spalding 211948C – Manual in PDF format online.

Manuals:

Manual

Manual Spalding 211948C

Summary

Page 2 - from holes if necessary.

2 P/N 211948C 01/04 BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular...

Page 3 - WARNING

01/04 P/N 211948C 3 WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or...

Page 4 - SAFETY INSTRUCTIONS; MOVING SYSTEM

4 P/N 211948C 01/04 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble th...

Page 6 - FRONT

6 P/N 211948C 01/04 Get to know the basic parts of your basketball system..... STRUT BACKBOARD FRONT RIM BASE POLE ELEVATOR SYSTEM WHEEL CARRIAGE ASSEMBLY

Page 9 - ITEMS NOT USED WITH THIS MODEL

01/04 P/N 211948C 9 * You may have extra parts with this model. HARDWARE IDENTIFIER (METAL RODS, SPACERS & WASHERS) HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS) Item #30 (2) Item #37 (8) Item #55 (2) Item #57 (4) Item #43 (12) Item #13 (11) Item #7 (1) Item #6 (2) ITEMS NOT USED WITH THIS M...

Page 10 - ASSEMBLE THE BASE; Wrenches

10 P/N 211948C 01/04 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION A: ASSEMBLE THE BASE This is what your system will look likewhen you’ve finished this section: Item #10 Item #14 Item #15 Item #16 Item #19 Item #22 Item #18 Item #39 Item #50 Item #33 Item #...

Page 11 - DO NOT OVER; Mark pole sections with tape as shown.

01/04 P/N 211948C 11 1. Install wheel axle (64) through wheel carriage (65) and install wheels (5) onto wheel axle (64) with spacers (6)as shown. Secure wheel bracket as shown, a deep socket is recommended. 2. 18 13 34 5" (13 cm) MIDDLE TOP 5" (13 cm) BOTTOM 1 2 3 IMPORTANT!: DO NOT OVER TIG...

Page 16 - Carefully reposition entire assembly as shown.

16 P/N 211948C 01/04 13. Carefully reposition entire assembly as shown. Attach front of plastic handle (26) to back of plastichandle (23) around handle bar (20) using self-tapping screws (27) as shown. IMPORTANT! Front of plastic handle (26) shouldface outward, away from pole assembly. Insert bolts ...

Page 17 - Assemble

01/04 P/N 211948C 17 17. 34 57 56 55 53 57 Attach spacers (55, 56) to pole mount bracket (53) with bolts(33), washers (57), and nuts (34) as shown. IMPORTANT! Tighten until washers (57) no longer move. 18. 33 53 14 60 58 59 Attach covers (58) onto pole mountbracket (53) with carriage bolt (39) andnu...

Page 19 - ATTACH THE BACKBOARD

01/04 P/N 211948C 19 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION B: ATTACH THE BACKBOARD This is what your system will look likewhen you’ve finished this section: AND/OR 9/16” 1/2” Socket Extension (2) Socket Wrenches and Sockets (2) 1/2”, (2) 9/16" AN...

Page 20 - ELEVATOR INSTALLATION

20 P/N 211948C 01/04 21. ELEVATOR INSTALLATION 22. 31 30 34 33 29 32 35 38 37 36 35 29 42 37 Install spacers (30) onto backboard brackets (29) with bolts (31, 33) and lock nuts (32, 34) as shown. Assemble lower elevator tubes (35) as shown. Tighten completely. IMPORTANT! It is necessary for all part...

Page 21 - Do not use washers here on spring return style rim.

01/04 P/N 211948C 21 24. 23. 29 14 61 14 39 38 36 37 37 40 40 29 Note Starting with nuts (14) flush against bracket (29), secure rim (61) and bracket to backboard. IMPORTANT! For spring loaded rim assembly, refer to instructions included with rim hardware. NOTE: Do not use washers here on spring ret...

Page 22 - Before going onto

22 P/N 211948C 01/04 25. 1 38 36 40 41 40 35 35 38 36 35 35 37 26. 42 38 36 40 40 27. Support pole on sawhorse. Attach backboard assembly to top pole section (1). Then install pole cap (41). NOTE: Two people are recommended for this step. Use caution; elevator assembly is heavy. Install handle assem...

Page 23 - HEIGHT ADJUSTMENT; Move elevator up or down to desired height.

01/04 P/N 211948C 23 10 ft. (3.05 m) 28. 32. HEIGHT ADJUSTMENT 30. 31. 29. 60 29. 31. 30. 46 44 45 TWO PEOPLE REQUIREDFOR THIS PROCEDURE.FAILURE TO FOLLOW THISWARNING COULD RESULTIN SERIOUS INJURY AND/ORPROPERTY DAMAGE. WARNING! DO NOT ALLOW CHILDREN TOADJUST HEIGHT. WARNING! DO NOT LEAVE ASSEMBLYUN...

Page 24 - NET INSTALLATION

24 P/N 211948C 01/04 33. Install clips. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly sothat second “arm” slides over the top of the first “arm” as shown.Push in direction indicated by arrows. Push second “arm” back and into ram as shown. Twist “bod...

Page 25 - Insert net into bottom of clip as shown.

01/04 P/N 211948C 25 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position.Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP 34. 61 43 62