Spalding 211789 - Manuals

8 P/N 211789 02/04 SECTION A: ASSEMBLE THE POLES 2. 1. Wood Scrap 2 1 5" (13 cm) 5" (13 cm) 1 3 2 Correctly identify each pole section. Mark pole sections with tape as shown. TAPE (not supplied) TAPE (not supplied) Bounce middle pole section (2) into top pole section (1) together using a woo...

02/04 P/N 211789 9 IMPORTANT! Holes in top (1) and bottom pole (3) sections MUST align to correctlyposition elevator system toward playing surface. While maintaining alignment, bounce assembly and lower section (3) together as shown until they no longer move toward taped reference mark. 1 2 3 3. WOO...

10 P/N 211789 02/04 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION B: ASSEMBLE THE BASE 1/2” & 9/16” 9/16” & 1/2” AND EXTENSION HAMMER OR MALLET AND This is what your system will look like whenyou’ve finished this section: Item #7 Item #10 Item #11 It...

02/04 P/N 211789 11 1. 2. Insert axle (5) through wheel bracket (4). Secure wheels (65) to axle using pushnuts (7). Carefully tap pushnuts onto axle with hammer or mallet 4 65 65 7 7 5 Install wheel assembly to base (8) using bolt (9), and nut (22) as shown. 9 22 9 8

02/04 P/N 211789 17 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION C: ASSEMBLE THE ELEVATOR SYSTEM & BACKBOARD WRENCHES (2) 1/2”, (2) 3/4” AND (2) 9/16” This is what your system will look like whenyou’ve finished this section: Item #22 Item #37 Item #38 I...

18 P/N 211789 02/04 1. Securely rest the assembly on sawhorse. Install pole bracket (36) to top pole as shown (FIG.A) using bolts (38), metal spacers (63) and nuts (22). Reference finished assembly (FIG.B.) FIG.A 36 38 22 63 63 & 38 22 36 FIG.B FLAT SIDE TOWARDS BASE. COMPLETED ASSEMBLY TWO PEOP...

20 P/N 211789 02/04 3. Attach label (60) to window (27). Important: Line up top edge of label with top edge of window COMPLETED ASSEMBLY COMPLETED ASSEMBLY 60 27 4. Remove packaging materials and zip ties from handle assembly (30)Snap window into handle assembly (30) 30

02/04 P/N 211789 25 Secure metal spacer (28) between board brackets (49) with bolt (47), washer (66), and nut (48). 14. 48 47 28 66 49 46 46 47 47 48 48 Assemble brackets (49) to backboard using bolts (47) metal spacers (46) and nuts (48) as shown.The spacers may fit very tightly between the bracket...

28 P/N 211789 02/04 17. Install net clips. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip (52) into ram as shown. Twist “body” ofclip slightly so that second “arm” slides over the top of the first“arm” as shown.Push in direction indicated by arrows. Push second “arm” back and into ram as shown. Twi...

02/04 P/N 211789 29 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position.Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP 18. 52 53 Install net. 8

30 P/N 211789 02/04 SECTION D: INSTALL FRONT COVER & HANDLE 1. Attach front cover (50) to hinge tubes (18) using carriage bolts (51) and flange nuts (15)as shown. 50 51 22 18 Upright system and fill base (8) with water (approx. 40 gallons) and snap fill cap (54) in place. 54 2. DO NOT LEAVEASSEM...

02/04 P/N 211789 31 1. SECTION E: SECURING THE SYSTEM Roll assembly to desired playing area. Secure assembly toground using strap (56) and tie down stake (55). 56 55 8

32 P/N 211789 02/04 1. Apply Height Adjustment and Moving Label (57) to front of pole, where it is clearly visible. Remove strut locking clip. SECTION F: APPLY HEIGHT AND MOVING LABEL Peel protective film from surface of acrylic backboard prior to use. NOTE: 203532 01/04 MOVING SYSTEM 1. Adjust bask...