SMC Networks SMC108DT - Manuals

Copyright Information furnished by SMC Networks, Inc. (SMC) is believed to beaccurate and reliable. However, no responsibility is assumed by SMC forits use, nor for any infringements of patents or other rights of thirdparties which may result from its use. No license is granted by implica-tion or ot...

Page 3 - Limited Warranty; SMC's Limited Warranty

Limited Warranty SMC's Limited Warranty Limited Warranty Statement: SMC Networks, Inc. ("SMC") warrants itsproducts to be free from defects in workmanship and materials, undernormal use and service, for the applicable warranty term. All SMCproducts carry a standard 90-day limited warranty fr...

Page 6 - Compliances; FCC Class B; Safety Compliance; Operating Voltage

Compliances FCC Class B This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates,...

Page 8 - TABLE OF CONTENTS; TROUBLESHOOTING

TABLE OF CONTENTS Copyright 2002 by .................................................................................................1 TABLE OF CONTENTS ..........................................................................................4 Features and Benefits ....................................

Page 9 - Features and Benefits

ABOUT THE EZ Switch 10/100 The EZSwitch 10/100 SMC108DT is an 8-port Fast Ethernet switch. The10BASE-T/100BASE-TX ports deliver dedicated 10/100Mbps links to eachattached LAN segment – all with conventional cabling and adapters. Auto-Negotiation is used to select the optimal communication modefor ea...

Page 10 - Top Panel LEDs; LED; Condition; Status; Port and Switch status LEDs

Top Panel LEDs The top panel of the switch provides a link status LED for each RJ-45PORT. In addition, the front panel also contains status LEDs for ‘at-a-glance’ system monitoring. The following table details the functions ofthe various kinds of indicators: LED LED Power RJ-45 Ports100M Link/Act Co...

Page 11 - Rear Panel

Rear Panel The AC power socket and the 8 RJ-45 connectors are located on therear panel of the switch. FDX Flashing Off On Flashing OFF Traffic is passingthrough the portThe port has not estab-lished any network con-nection.The port is in full-duplexmode.Packet collision is occur-ring in half-duplex ...

Page 12 - INSTALLING THE SWITCH; Equipment Checklist; Selecting a Site

INSTALLING THE SWITCH The EZSwitch 10/100 can be placed on a desktop or shelf, or installed ina standard 19-inch equipment rack. Equipment Checklist After unpacking the EZSwitch 10/100, check the contents of the box tobe sure you have received the following components: . EZSwitch 10/100 SMC108DT. Ap...

Page 13 - : For desktop or shelf mounting, attach the; Applying power; : plug one end of the power cable into the power

Instructions 1. Positioning the switch : For desktop or shelf mounting, attach the four adhesive feet to the bottom of the switch. For wall mounting,please make sure that the hangars are securely attached to the sur-face, and then mount the switch onto the hangars.2. Applying power : plug one end of...

Page 14 - SAMPLE APPLICATIONS; Standalone LAN

SAMPLE APPLICATIONS Some typical applications for the EZ Switch 10/100 are illustratedbelow: Standalone LAN In the figure below, the EZSwitch 10/100 is operating as a collapsedbackbone for a small LAN. It is providing dedicated 10Mbps full-duplexconnections to workstations and 200Mbps full-duplex co...

Page 15 - Probable cause

TROUBLESHOOTING 1. S Sy ym mp ptto om m Power LED does not light after power on Probable cause Power outlet or power cord may be defective Possible Solutions . Check for loose connections.. Check the power outlet by using it for another device.. Replace the power cord. 2. S Sy ym mp ptto om m Link L...

Page 16 - CABLES; Cable Specifications

CABLES Cable Specifications Twisted-Pair Cable and Pin Assignments Caution: DO NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pair cables with RJ-45 connectors that conform toFCC standards. For 10BASE-T/100BASE-TX connections, a twisted-pair cable must havetwo pairs of wires. ...

Page 17 - Connectivity Guidelines

Connectivity Guidelines When adding hubs (repeaters) to your network, please follow the con-nectivity rules listed below for Fast Ethernet. However, note thatbecause switches break up the path for connected devices into sepa-rate collision domains, you should not include the switch or connectedcabli...

Page 18 - SPECIFICATIONS; K entries per system

SPECIFICATIONS EZ Switch 10/100 Model SMC108DT Ports 8 RJ-45 Network Interface RJ-45: 100 ohm, UTP cable10BASE-T – EIA/TIA Categories 3,4 5100BASE-TX – EIA/TIA Category 5 LEDs Power- OneLink/Act (Activity) – one per port10/100 (10/100Mbps) – one per portFDX/COL (full duplex/collision) one per port S...

Page 19 - Standards

0.22@240VAC Standards IEEE802.3IEEE802.3uIEEE802.3xISO/IEC8802-3