SEAGATE ST980821A - Manuals

Momentus 5400 FDE Product Manual, Rev. C 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® Momentus ® 5400 FDE drives: • ST9120826A • ST9100826A • ST980821A • ST960814A • ST940811A These drives provide the following key featu...

2 Momentus 5400 FDE Product Manual, Rev. C 1.2 About Momentus 5400 FDE disc drives The Momentus 5400 FDE contains drive trust technology providing Full-Disc Encryption (FDE) using proven Triple DES (TDES) data encryption and decryption. Feature list • Automatically encrypts (and decrypts) all data o...

Momentus 5400 FDE Product Manual, Rev. C 5 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST9120826A, ST9100826A, ...

Momentus 5400 FDE Product Manual, Rev. C 7 * One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. **During periods of drive idle, some offline activity may occur, according to the S.M.A.R.T. specific...

8 Momentus 5400 FDE Product Manual, Rev. C 2.5 Recording and interface technology 2.6 Physical characteristics Technology Specification Interface Parallel ATA Recording method RLL 0,11 Recording density BPI (bits/inch typical) 778,000 Track density TPI (tracks/inch typical) 126,000 Areal density (Gb...

Momentus 5400 FDE Product Manual, Rev. C 9 2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications below are defined as follows: • Track-to-track seek time is an average of all possible single-track ...

10 Momentus 5400 FDE Product Manual, Rev. C 2.9 Power specifications The drive receives DC power (+5V) through the interface connector. 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 10. Typical power measurements are based on an average of drives tested, u...

Momentus 5400 FDE Product Manual, Rev. C 11 2.9.1.1 Typical current profile Figure 5. Typical 5V startup and operation current profile 2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt pow...

Momentus 5400 FDE Product Manual, Rev. C 13 2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 65°C (149°F) within the operating ambient c...

14 Momentus 5400 FDE Product Manual, Rev. C 2.10.5.2 Nonoperating shock The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse of 2 msec d...

Momentus 5400 FDE Product Manual, Rev. C 15 2.12 Electromagnetic immunity When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency (RF) environments defined in the following table: A - 1) No upset o...

16 Momentus 5400 FDE Product Manual, Rev. C 2.13 Reliability 2.14 Agency certification 2.14.1 Safety certification The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950 as tested by TUV North America. 2.14.2 Electromagnetic c...

Momentus 5400 FDE Product Manual, Rev. C 17 Korean RRL If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para-graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework r...

18 Momentus 5400 FDE Product Manual, Rev. C 2.15 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. European Union Restriction of Hazardous Substances (RoHS) The European Union ...

Momentus 5400 FDE Product Manual, Rev. C 19 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. Momentus ® 5400 FDE drives can be connected to a computer system using a standard IDE interface cable and power connect...

20 Momentus 5400 FDE Product Manual, Rev. C 3.2 Jumper settings 3.2.1 Master/slave configuration Use the options jumper block shown in Figure 6 to configure the drive for operation. This jumper block is the 4-pin header adjacent to pins 1 and 2 of the I/O signal pins. For additional information abou...

Momentus 5400 FDE Product Manual, Rev. C 21 Figure 7. Mounting dimensions—top, side and end view Breather Hole Do not coveror seal. 2X M3 X 0.5-6HMounting holesBoth sides .12 min. full thread .160 (4.06) 3.567 (90.60) 4X M3 X 0.5-6HMounting holes .10 min. full thread 2.430 (61.72) .551 (13.99) .551 ...

22 Momentus 5400 FDE Product Manual, Rev. C 3.4 Drive integration The Momentus 5400 FDE may be installed in the target computer system in exactly the same way as a non-FDE Momentus drive with one optional exception regarding the label. Figure 8. Momentus 5400 FDE drive label example To install the d...

Momentus 5400 FDE Product Manual, Rev. C 23 3.4.1 Drive installation Upon receipt by the consumer, the drive’s user interface is identical to a Momentus 5400.2 drive. The normal ATA security commands are functioning and available for initialization of the password as follows: Per normal ATA Security...

24 Momentus 5400 FDE Product Manual, Rev. C 6. The software or BIOS issues the Security Erase Prepare (F3) command. 7. The software or BIOS issues the Security Erase Unit (F4) command. Select the Enhanced erase for cryptographic erase that completes in less than one second. 3.5.3 Drive State after s...

Momentus 5400 FDE Product Manual, Rev. C 25 4.0 ATA interface These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports ATA programmed input/output (PIO) modes 0–4 and Ultra DMA modes 0–5. The drive also supports the use of the IORDY signal to pr...

26 Momentus 5400 FDE Product Manual, Rev. C 4.1.1 ATA interface specifications The Momentus 5400 FDE is consistent with the ATA Interface implementation of the Momentus 5400.2 prod-ucts with the known exceptions listed within this section (Section 4.1.1 subordinate sections). 4.1.1.1 Legacy mode -- ...

Momentus 5400 FDE Product Manual, Rev. C 27 4.1.1.4 Device 0 only configurations Per the ATA-ATAPI-7, Rev. 4B specification, Clause 5.16.1 (see italicized excerpt below), the specification expects Device 0 to return the Task File Register when Device 1 is selected as follows: In a single device conf...

28 Momentus 5400 FDE Product Manual, Rev. C Choosing the Enhanced Erase mode will simply perform the Cryptographic Erase described above, and return status almost immediately. This is the recommended option. To maintain consistency with the ATA Security specification, Momentus 5400 FDE drives provid...

Momentus 5400 FDE Product Manual, Rev. C 29 4.1.4 Drive Trust Mode supported Identify Page - Word 150 decimal (0x96h)- Bit 12 Identifies Drive Trust Support. Value = 1 = Drive Trust is supported (this is a trusted drive) Table 9: Drive Trust Identify Page Ident Value BIT set Bit Description 5 0 15 V...

32 Momentus 5400 FDE Product Manual, Rev. C 29 READ MULTIPLE EXT Aborted Executable Executable Aborted Executable F8 READ NATIVE MAX ADDRESS Executable Executable Executable Executable Executable 27 READ NATIVE MAX ADDRESS EXT Executable Executable Executable Executable Executable 20 READ SECTOR(S) ...

Momentus 5400 FDE Product Manual, Rev. C 35 4.1.7 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data. All reserved bits or words should be set to zero....

Momentus 5400 FDE Product Manual, Rev. C 39 5.0 Compatibility summary 5.1 Installation considerations Many of today’s mobile computers have been designed to make it possible for the end user to replace the hard drive. Refer to your system’s user manual for the location of the hard drive compartment ...

40 Momentus 5400 FDE Product Manual, Rev. C System Compatibility Seagate Product Assurance has tested Momentus drives in the systems listed in Table 13. Testing included multiple BIOS versions and operating systems. This testing was done to demonstrate compatibility with various hardware and softwar...

Momentus 5400 FDE Product Manual, Rev. C 41 5.3 Operating system versions tested This list indicates the types of Operating Systems Seagate tested during the compatibility testing process and highlights the major OS manufacturers. Several variations of the major operating systems have been tested. 5...

42 Momentus 5400 FDE Product Manual, Rev. C 5.5.1 Third party software support Seagate does not supply password management software. Third party software support for security features is available. For the latest list of available software, please refer to the following web site: http://www.seagate....

Momentus 5400 FDE Product Manual, Rev. C 43 6.0 Seagate Technology support services Internet For information regarding Seagate products and services, visit www.seagate.com . Worldwide support is available 24 hours daily by email for your questions. Presales Support: [email protected] Technical Su...

44 Momentus 5400 FDE Product Manual, Rev. C Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warranty-re...

Momentus 5400 FDE Product Manual, Rev. C 45 Index Numerics 3D Defense System 1 A acoustics 14 Active mode 12 AFR 16 agency certification (regulatory) 16 altitude 13 ambient conditions 5 ambient temperature 9 , 13 Annualized Failure Rate 16 areal density 8 ATA interface 25 ATA-standard commands 31 Au...