SEAGATE ST980813AS - Manuals

Momentus 7200.2 SATA Product Manual, Rev. E 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate Momentus ® 7200.2 SATA model drives: • ST9200420ASG • ST9200420AS • ST9160823ASG • ST9160823AS • ST9120823AS • ST9100821AS • ST980813...

2 Momentus 7200.2 SATA Product Manual, Rev. E 1.1 About the Serial ATA (SATA) interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation and configuration with true plug-and-play connectivity. It i...

Momentus 7200.2 SATA Product Manual, Rev. E 3 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate theST9200420ASG, ST92...

Momentus 7200.2 SATA Product Manual, Rev. E 5 *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. **During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specifi...

6 Momentus 7200.2 SATA Product Manual, Rev. E 2.4 Physical organization 2.5 Recording and interface technology 2.6 Physical characteristics Drive model Read/write heads Number of discs ST9200420AS and ST9200420ASG 4 2 ST9160823AS and ST9160823ASG ST9120823AS 3 ST9100821AS ST980813AS and ST980813ASG ...

Momentus 7200.2 SATA Product Manual, Rev. E 7 2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: • Track-to-track seek time is an average of all possib...

8 Momentus 7200.2 SATA Product Manual, Rev. E 2.9 Power specifications The drive receives DC power (+5V) through a native SATA power connector. 2.9.1 Power consumption Power requirements for the drives are listed in Table 3, on page 8. Typical power measurements are based on an average of drives tes...

Momentus 7200.2 SATA Product Manual, Rev. E 9 2.9.1.1 Typical current profile Figure 1. Typical 5V startup and operating current profile 2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt p...

Momentus 7200.2 SATA Product Manual, Rev. E 11 2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 65°C (149°F) within the operating ambien...

Momentus 7200.2 SATA Product Manual, Rev. E 13 2.11 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea-surements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a ref...

14 Momentus 7200.2 SATA Product Manual, Rev. E 2.13 Reliability 2.13.1 Free Fall Protection feature The Free Fall Protection feature provides enhanced data protection against shock events that may occur while the drive is operating. This feature is designed to decrease the likelihood of data loss by...

Momentus 7200.2 SATA Product Manual, Rev. E 15 Korean RRL If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para-graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framewor...

16 Momentus 7200.2 SATA Product Manual, Rev. E 2.15 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.15.1 European Union Restriction of Hazardous Substances (RoHS) Directive...

Momentus 7200.2 SATA Product Manual, Rev. E 19 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to ...

20 Momentus 7200.2 SATA Product Manual, Rev. E 3.2 Configuring the drive Each drive on the Serial ATA interface connects in a point-to-point configuration with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point relationshi...

Momentus 7200.2 SATA Product Manual, Rev. E 21 3.4 Drive mounting You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 4 for drive mounting dimensions. Follow these important mounting precautions when mount-ing the drive: • Allo...

Momentus 7200.2 SATA Product Manual, Rev. E 23 4.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. The drive also suppo...

24 Momentus 7200.2 SATA Product Manual, Rev. E Notes: 1. All pins are in a single row, with a 1.27 mm (0.050”) pitch. 2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are: • the ground pins P4 and P12. • the pre-charge...

Momentus 7200.2 SATA Product Manual, Rev. E 25 4.3 Supported ATA commands The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification. See “S.M.A.R.T. comman...

Momentus 7200.2 SATA Product Manual, Rev. E 27 4.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table on page ...

Momentus 7200.2 SATA Product Manual, Rev. E 29 90 Enhanced security erase time 0000 H 92 Master password revision code FFFE H 93 Hardware reset value (see description following this table) xxxx H 94 Auto acoustic management setting xxxx H 95–99 ATA-reserved 0000 H 100–103 Total number of user-addres...

30 Momentus 7200.2 SATA Product Manual, Rev. E 4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-rupt. If ...

Momentus 7200.2 SATA Product Manual, Rev. E 31 Note. At power-on, or after a hardware or software reset, the default values of the features are as indi-cated above. 4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive moni-...

Momentus 7200.2 SATA Product Manual, Rev. E 33 5.0 Seagate Technology support services Online Services Internet For information regarding Seagate products and services, visit www.seagate.com . Worldwide support is available 24 hours daily by email for your questions. Presales Support: Presales@Seaga...

34 Momentus 7200.2 SATA Product Manual, Rev. E Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warranty...

Momentus 7200.2 SATA Product Manual, Rev. E 35 Index A ACA 15 acoustics 4 , 13 Active mode 10 Address 25 AFR 14 Agency certification 14 Altitude 11 Altitude, nonoperating 4 Altitude, operating 4 Ambient temperature 4 , 11 ambient temperature 7 Annualized Failure Rate (AFR) 4 , 14 Areal density 3 , 6...