SEAGATE ST980811A - Manuals

Momentus 4200.3 PATA Product Manual, Rev. B 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® Momentus ® 4200.3 drives: • ST980811A • ST960813A • ST9408116A These drives provide the following key features: • 4,200-RPM class p...

Momentus 4200.3 PATA Product Manual, Rev. B 3 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST980811A, ST960813A,...

4 Momentus 4200.3 PATA Product Manual, Rev. B Table 1: Specifications for 100 and 80 Gbyte models Drive specification ST980811A ST960813A Formatted Gbytes (512 bytes/sector)* 80 60 Guaranteed sectors 156,301,488 117,210,240 Bytes per sector 512 Physical read/write heads 2 Discs 1 Cache (Mbytes) 8 Re...

6 Momentus 4200.3 PATA Product Manual, Rev. B Table 1: Specifications for 60 and 40 Gbyte models Drive specification ST9408116A Formatted Gbytes (512 bytes/sector)* 40 Guaranteed sectors 78,140,160 Bytes per sector 512 Physical read/write heads 1 Discs 1 Cache (Mbytes) 8 Recording density, BPI (bits...

8 Momentus 4200.3 PATA Product Manual, Rev. B 2.2 Formatted capacity *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.3 Default logical geometry LBA mode When addressing these drives in LBA mo...

Momentus 4200.3 PATA Product Manual, Rev. B 9 2.5 Recording and interface technology 2.6 Physical characteristics Technology Specification Interface Parallel ATA Recording method Perdendicular Recording density BPI (bits/inch typical) 835k Track density TPI (tracks/inch typical) 150k Areal density (...

10 Momentus 4200.3 PATA Product Manual, Rev. B 2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications below are defined as follows: • Track-to-track seek time is an average of all possible single-tr...

Momentus 4200.3 PATA Product Manual, Rev. B 11 2.9 Power specifications The drive receives DC power (+5V) through the interface connector. 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 11. Typical power measurements are based on an average of drives tested...

12 Momentus 4200.3 PATA Product Manual, Rev. B 2.9.1.1 Typical current profile Figure 4. Typical 5V startup and operation current profile 2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt ...

14 Momentus 4200.3 PATA Product Manual, Rev. B 2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 65°C (149°F) within the operating ambien...

16 Momentus 4200.3 PATA Product Manual, Rev. B 2.11 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea-surements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a ref...

Momentus 4200.3 PATA Product Manual, Rev. B 17 2.13 Reliability 2.14 Agency certification 2.14.1 Safety certification The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950 as tested by TUV North America. 2.14.2 Electromagneti...

Momentus 4200.3 PATA Product Manual, Rev. B 19 2.15 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.15.1 European Union Restriction of Hazardous Substances (RoHS) The Europ...

Momentus 4200.3 PATA Product Manual, Rev. B 21 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static discharge precautions After unpacking, and before installation, the drive may be exposed to ...

22 Momentus 4200.3 PATA Product Manual, Rev. B 3.2 Jumper settings 3.2.1 Master/slave configuration Use the options jumper block shown in Figure 5 to configure the drive for operation. This jumper block is the 4-pin header adjacent to pins 1 and 2 of the I/O signal pins. For additional information a...

Momentus 4200.3 PATA Product Manual, Rev. B 23 3.3 Drive mounting You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 6 for drive mounting dimensions (dimensions in inches with mm in parentheses). Follow these important mountin...

Momentus 4200.3 PATA Product Manual, Rev. B 25 4.0 ATA interface These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–5. The drive also supports the ...

26 Momentus 4200.3 PATA Product Manual, Rev. B 4.1.1 Supported ATA commands The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Draft ATA-6 Standard. Table 7: Supported commands Command name Command code (in hex) ATA-s...

Momentus 4200.3 PATA Product Manual, Rev. B 27 Security Unlock F2 H Seek 70 H Set Drive Parameters 91 H Set Features EF H Set Max Address F9 H Note: Individual Set Max com-mands are identified by the value placed in the Set Max Features register as defined to the right. Address Password Lock Unlock ...

Momentus 4200.3 PATA Product Manual, Rev. B 29 4.1.2 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 7 on page 26...

Momentus 4200.3 PATA Product Manual, Rev. B 33 5.0 Compatibility summary 5.1 Installation considerations Many of today’s mobile computers have been designed to make it possible for the end user to replace the hard drive. Refer to your system’s user manual for the location of the hard drive compartme...

Momentus 4200.3 PATA Product Manual, Rev. B 35 5.2 BIOS versions tested The following list indicates the types of BIOS Seagate tested during the compatibility testing process. The list highlights the major BIOS manufacturers. Individual systems contain variations of these BIOS versions and were test...

36 Momentus 4200.3 PATA Product Manual, Rev. B 5.3 Operating system versions tested This list indicates the types of Operating Systems Seagate tested during the compatibility testing process and highlights the major OS manufacturers. Several variations of the major operating systems have been tested...

Momentus 4200.3 PATA Product Manual, Rev. B 37 6.0 Seagate Technology support services Internet For information regarding Seagate products and services, visit www.seagate.com . Worldwide support is available 24 hours daily by email for your questions. Presales Support: [email protected] Technical...

38 Momentus 4200.3 PATA Product Manual, Rev. B Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warranty...

Momentus 4200.3 PATA Product Manual, Rev. B 39 Index Numerics 3D Defense System 1 A acoustics 16 Active mode 13 AFR 17 agency certification (regulatory) 17 altitude 14 ambient conditions 3 ambient temperature 10 , 14 Annualized Failure Rate 17 areal density 9 ATA interface 25 ATA-standard commands 2...