SEAGATE ST980414ASG - Manuals

Momentus 7200 FDE.1 SATA Product Manual, Rev. A iii List of Figures Figure 1. Typical +5V only startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 2. Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate Momentus ® 7200 FDE.1 SATA model drives: These drives provide the following key features: • DriveTrust technology including: • Ha...

2 Momentus 7200 FDE.1 SATA Product Manual, Rev. A 1.2 About Momentus 7200 FDE.1 SATA disc drives Momentus ® 7200 FDE.1 SATA drives contain DriveTrust technology providing Full Disc Encryption (FDE) using proven Advanced Encryption Standard (AES) data encryption and decryption. You can elect to use M...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 3 Having the encryption/decryption on the drive also provides the highest level of security for data because all data, including the boot sector bytes, operating system, temp and even the swap files are encrypted at the drive level. 1.2.1 Drive state u...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 5 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. 2.1 Specification summary table The specifications listed in this table are for quick reference. For details on spe...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 7 and formatting. **During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. ***Typical notebooks will pull power to the drive when entering S3...

8 Momentus 7200 FDE.1 SATA Product Manual, Rev. A 2.4 Physical organization 2.5 Recording and interface technology 2.6 Physical characteristics Drive model Read/write heads Number of discs ST9320424AS and ST9320424ASG 4 2 ST9250424AS and ST9250424ASG 3 2 ST9160414AS and ST9160414ASG 2 1 ST9120414AS ...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 9 2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: • Track-to-track seek time is an average of all po...

10 Momentus 7200 FDE.1 SATA Product Manual, Rev. A 2.9 Power specifications The drive receives DC power (+5V) through a native SATA power connector. 2.9.1 Power consumption Power requirements for the drives are listed in table 3. Typical power measurements are based on an average of drives tested, u...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 11 2.9.1.1 Typical current profile Figure 1. Typical +5V only startup and operation current profile 2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Usi...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 13 2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 65°C (149°F) within the operating am...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 15 2.11 Acoustics Drive emission of sound is measured consistent with the ECMA-74 and its’ referenced standards. Testing is conducted at room temperature (approximately 25 ° C). Emission levels are reported as the total A-weighted sound power levels fo...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 17 2.13 Reliability 2.13.1 Free Fall Protection feature The Free Fall Protection feature provides enhanced data protection against shock events that may occur while the drive is operating. This feature is designed to decrease the likelihood of data los...

18 Momentus 7200 FDE.1 SATA Product Manual, Rev. A 2.14.2 Electromagnetic compatibility Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec-tromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the pr...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 19 • Move the device farther away from the radio or TV. • Plug the computer into a different outlet so that the receiver and computer are on different branch outlets. If necessary, you should consult your dealer or an experienced radio/television techn...

20 Momentus 7200 FDE.1 SATA Product Manual, Rev. A 2.15 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.15.1 European Union Restriction of Hazardous Substances (RoHS) Seaga...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 21 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. Momentus ® 7200 FDE.1 SATA drives may be connected to any computer system that supports a standard SATA interfac...

22 Momentus 7200 FDE.1 SATA Product Manual, Rev. A • Do not obstruct the breather hole located on the top cover of the drive. Refer to Figure 4 for the exact location of this hole. 3.2 Configuring the drive Each drive on the Serial ATA interface connects in a point-to-point configuration with the Se...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 23 3.4 Drive mounting You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 4 for drive mounting dimensions. Follow these important mounting precautions when mount-ing the drive: • ...

24 Momentus 7200 FDE.1 SATA Product Manual, Rev. A 3.5 Drive integration Momentus 7200 FDE.1 SATA drives may be installed in the target computer system in exactly the same way as a non-FDE Momentus drive. . Figure 5. Momentus 7200 FDE.1 SATA drive label example To install the drive in the system: 1....

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 27 4.0 Serial ATA interface These drives use the industry-standard Serial ATA (SATA) interface that supports FIS data transfers. It sup-ports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. The drive also ...

28 Momentus 7200 FDE.1 SATA Product Manual, Rev. A Notes: 1. All pins are in a single row, with a 1.27 mm (0.050”) pitch. 2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are: • the ground pins P4 and P12. • the pre-ch...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 29 4.2.1 ATA Security policy exceptions In the ATA Security Interface mode, the drive conforms to the ATA Security Policy, except the following desir-able exceptions to implement the desired Momentus 7200 FDE.1 SATA behavior: Upon execution of the secu...

30 Momentus 7200 FDE.1 SATA Product Manual, Rev. A 4.2.2 DriveTrust Mode support Identify Page - Word 150 decimal (0x96h)- Bit 12 Identifies DriveTrust Support. Value = 1 = DriveTrust is supported Table 7: DriveTrust Identify Page Ident Value BIT set Bit Description 5 0 15 Vendor specific 1 14 Vendo...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 33 2F READ LOG EXT Executable Executable Executable Executable Executable C4 READ MULTIPLE Aborted Executable Executable Aborted Executable 29 READ MULTIPLE EXT Aborted Executable Executable Aborted Executable F8 READ NATIVE MAX ADDRESS Executable Exec...

36 Momentus 7200 FDE.1 SATA Product Manual, Rev. A 4.2.5 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table belo...

38 Momentus 7200 FDE.1 SATA Product Manual, Rev. A 85 Command sets enabled 34xx H 86 Command sets enabled BC09 H 87 Command sets enable extension 61E3 H 88 Ultra DMA support and current mode (see note following this table) xx7F H 89 Security erase time 0001 H 90 Enhanced security erase time 0001 H 9...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 39 4.2.6 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-rupt....

40 Momentus 7200 FDE.1 SATA Product Manual, Rev. A Note. At power-on, or after a hardware or software reset, the default values of the features are as indi-cated above. Table 10: Set Features command values 02 H Enable write cache (default). 03 H Set transfer mode (based on value in Sector Count reg...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 41 4.2.7 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive moni-tors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines t...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 43 5.0 Compatibility summary 5.1 Installation considerations Many of today’s mobile computers have been designed to make it possible for the end user to replace the hard drive. Refer to your system’s user manual for the location of the hard drive compa...

44 Momentus 7200 FDE.1 SATA Product Manual, Rev. A AMD K8 PHOENIX AWARD V5.1.39 AMD K8 PHOENIX AWARD V6.00PG AMD K8 PHOENIX AWARD AMD K8 PHOENIX DELL 1.1.2 AMD K8 PHOENIX VER 2004Q3 AMD K8 PHOENIX ATI 0X5A31 INSYDE R1.00 ATI RS400-200 AMI V02.59 ATI RS400-200 AMI V0707 ATI RS480 AMERICAN MEGATRENDS ...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 47 Table 13: DriveTrust compatibility Chipset Manufacturer Chipset Southbridge System Vendor System Model SATA Mode BIOS Intel ICH6M LG LW40-DOX1 ATA Phoenix OLMPSF07 TCL K40D ATA Phoenix1.00 ICH7M Acer Aspire 3690 BL50 ATA Phoenix V3.50 Aspire 5572WXM...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 49 5.3 Operating system versions tested This list indicates the types of Operating Systems Seagate tested during the compatibility testing process. Sev-eral variations of these operating systems have been tested. Intel ICH8M HP-BPC Compaq 2210B AHCI HP...

50 Momentus 7200 FDE.1 SATA Product Manual, Rev. A 5.4 Compatibility test configurations Tests are performed to ensure functionality to the ATA/ATAPI-7 specification and are constantly evolving to match the evolution of the ATA/ATAPI specifications. Momentus 7200 FDE.1 SATA drives should be expected...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 51 6.0 Seagate Technology support services Internet For information regarding Seagate products and services, visit www.seagate.com . Worldwide support is available 24 hours daily by email for your questions. Presales Support: [email protected] Techn...

52 Momentus 7200 FDE.1 SATA Product Manual, Rev. A Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warr...

Momentus 7200 FDE.1 SATA Product Manual, Rev. A 53 Index A ACA 18 acoustics 6 , 15 Active mode 12 AFR 17 Agency certification 17 Altitude 13 Altitude, nonoperating 6 Altitude, operating 6 Ambient temperature 6 , 13 ambient temperature 9 Annualized Failure Rate 17 Annualized Failure Rate (AFR) 6 Area...