SEAGATE ST980210A - Manuals

LD25 Series 5400.2 Product Manual, Rev. C iii List of Figures Figure 1. Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 2. Breather filter hole location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

LD25 Series 5400.2 Product Manual, Rev. C 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® LD25 Series 5400.2 drives: Parallel ATA (PATA) Serial ATA (SATA) ST980210A ST980210AS ST960210A ST960210AS ST940210A ST940210AS ST920...

LD25 Series 5400.2 Product Manual, Rev. C 3 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST980210A, ST980210AS, ...

LD25 Series 5400.2 Product Manual, Rev. C 5 Table 2: Specifications for SATA (Serial ATA) models Drive specification ST980210AS ST960210AS ST940210AS ST920210AS Formatted Gbytes (512 bytes/sector)* 80 60 40 20 Guaranteed sectors 156,501,488 117,210,240 78,340,160 41,021,800 Bytes per sector 512 Defa...

6 LD25 Series 5400.2 Product Manual, Rev. C *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. * During periods of drive idle, some offline activity may occur, according to the S.M.A.R.T. specific...

8 LD25 Series 5400.2 Product Manual, Rev. C 2.6 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications below are defined as follows: • Track-to-track seek time is an average of all possible single-track...

LD25 Series 5400.2 Product Manual, Rev. C 9 2.8 Power specifications The drive receives DC power (+5V) through the 4-pin power connector. 2.8.1 Power consumption Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on an average of drives tested, ...

10 LD25 Series 5400.2 Product Manual, Rev. C 2.8.1.1 Typical current profile Figure 1. Typical 5V startup and operation current profile 2.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt po...

12 LD25 Series 5400.2 Product Manual, Rev. C 2.9 Environmental specifications 2.9.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 65°C (149°F) within the operating ambient co...

14 LD25 Series 5400.2 Product Manual, Rev. C 2.10 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels. All measurements are con-sistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For...

LD25 Series 5400.2 Product Manual, Rev. C 15 2.12 Reliability 2.13 Agency certification 2.13.1 Safety certification The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950 as tested by TUV North America. 2.13.2 Electromagnetic ...

16 LD25 Series 5400.2 Product Manual, Rev. C Korean RRL If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para-graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework ...

LD25 Series 5400.2 Product Manual, Rev. C 17 2.14 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.14.1 European Union Restriction of Hazardous Substances (RoHS) The Europea...

LD25 Series 5400.2 Product Manual, Rev. C 19 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to po...

20 LD25 Series 5400.2 Product Manual, Rev. C Measurements shown below are in inches. Figure 2. Mounting dimensions—top, side and end view BOTH SIDES 2 2 .12 MIN FULL THREAD 2X M3 X 0.5-6H MOUNTING HOLES; BOTH SIDES 0.148 ±.010 X 90 4X M3 X 0.5-6H MOUNTING HOLES; BOTH SIDES .10 MIN FULL THREAD 0.148 ...

LD25 Series 5400.2 Product Manual, Rev. C 21 3.3 Breather filter hole precautions Observe the following breather filter hole precautions to ensure full functionality and prevent possible damage to the drive. Figure 3 Breather filter hole location Caution: Do not cover, seal, or insert any object int...

22 LD25 Series 5400.2 Product Manual, Rev. C 3.4 How to configure the drive See Section 3.4.1 on page 22 for SATA drives. See Section 3.4.2 on page 23 for PATA drives. 3.4.1 How to configure and connect Serial ATA (SATA) drives 3.4.1.1 How to configure the drive Each drive on the SATA interface conn...

LD25 Series 5400.2 Product Manual, Rev. C 23 Each cable is keyed to ensure correct orientation. 3.4.2 How to configure Parallel ATA (PATA) drives Use the options jumper block shown in Figure 6 to configure the drive for operation. This jumper block is the 4-pin header adjacent to pins 1 and 2 of the...

LD25 Series 5400.2 Product Manual, Rev. C 25 4.0 Interface The following sections apply to both SATA and PATA drives. • Supported commands (see section 4.3 on page 29) • Identify Device command (see section 4.4 on page 31) • Set Features command (see section 4.5 on page 35) • S.M.A.R.T. commands (se...

26 LD25 Series 5400.2 Product Manual, Rev. C 4.1 Serial ATA (SATA) Interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. The drive also support...

LD25 Series 5400.2 Product Manual, Rev. C 27 Notes: 1. All pins are in a single row, with a 1.27 mm (0.050”) pitch. 2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are: • the ground pins P4 and P12. • the pre-charge p...

28 LD25 Series 5400.2 Product Manual, Rev. C 4.2 Parallel ATA (PATA) Interface These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–5. The drive also...

LD25 Series 5400.2 Product Manual, Rev. C 29 4.3 Supported commands The following table lists the standard commands that the drive supports. See “S.M.A.R.T. commands” on page 36.for details and subcommands used in the S.M.A.R.T. implementation. Command name Command code (in hex) ATA-standard command...

LD25 Series 5400.2 Product Manual, Rev. C 31 4.4 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table on page 27. ...

LD25 Series 5400.2 Product Manual, Rev. C 33 87 Command sets enable extension 4000 H 88 Ultra DMA support and current mode (see note following this table) xx3F H 89 Security erase time 0000 H 90 Enhanced security erase time 0000 H 92 Master password revision code FFFE H 93 Hardware reset value (see ...

LD25 Series 5400.2 Product Manual, Rev. C 35 4.5 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-rupt. If the ...

36 LD25 Series 5400.2 Product Manual, Rev. C 4.6 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive moni-tors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a fa...

LD25 Series 5400.2 Product Manual, Rev. C 37 5.0 Seagate Technology support services Internet For information regarding Seagate products and services, visit www.seagate.com . Worldwide support is available 24 hours daily by email for your questions. Presales Support: [email protected] Technical S...

38 LD25 Series 5400.2 Product Manual, Rev. C Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warranty-r...

LD25 Series 5400.2 Product Manual, Rev. C 39 Index Numerics 3D Defense System 1 A acoustics 14 Active mode 11 Address 29 AFR 15 agency certification (regulatory) 15 altitude 12 ambient conditions 3 ambient temperature 8 , 12 Annualized Failure Rate 15 areal density 7 ATA commands 29 Australian C-Tic...