SEAGATE ST9402116SB - Manuals

Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate Momentus ® 5400.3 SATA Blade Server model drives: • ST9160821SB • ST9120822SB • ST9100828SB • ST980815SB • ST960815SB • ...

2 Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 1.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation and configuration with true plug-and-play connectivity...

Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 3 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the ST91...

Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 5 *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. **Typical notebooks will pull power to the drive when entering S3 and S4; while in the...

6 Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 2.4 Physical organization 2.5 Recording and interface technology 2.6 Physical characteristics Drive model Read/write heads Number of discs ST9160821SB 4 2 ST9120822SB 3 2 ST9100828SB 3 2 ST980815SB 2 1 ST960815SB 2 1 ST9402116SB 1 1 Interfac...

Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 7 2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: • Track-to-track seek time is an average ...

8 Momentus 5400.3 SATA Blade Server Product Manual, Rev. E • Idle mode power Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in a random track location. • Standby mode During Standby mode, the drive accepts commands, but the drive is not spinn...

Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 9 2.9.2 Deferred spinup Momentus 5400.3 SATA drives provide a deferred spinup feature which storage subsystem controllers can use to sequence disc drive initialization. This is beneficial to systems which include multiple Serial ATA hard disc ...

10 Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Duty 50%, power-on hours (POH) of 8,750 per year (24 hours per day, 7 days ...

12 Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 2.11 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea-surements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditio...

Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 13 2.13 Reliability 2.14 Agency certification 2.14.1 Safety certification The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950 as tested by TUV North America. 2.14.2 E...

14 Momentus 5400.3 SATA Blade Server Product Manual, Rev. E Korean RRL If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para-graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (...

Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 15 2.15 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.15.1 European Union Restriction of Hazardous Substances (Ro...

Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 17 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may b...

18 Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 3.2 Configuring the drive Each drive on the Serial ATA interface connects in a point-to-point configuration with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-poin...

Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 19 3.4 Drive mounting You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 4 for drive mounting dimensions. Follow these important mounting precautions when mount-ing the ...

Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 21 4.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. The dri...

Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 23 4.3 Supported ATA commands The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification. See “S.M....

26 Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 4.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in the t...

28 Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 93 Hardware reset value (see description following this table) xxxx H 94 Auto acoustic management setting xxxx H 95–99 ATA-reserved 0000 H 100–103 Total number of user-addressable LBA sectors available (see Section 2.2 for related informati...

Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 29 4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an in...

30 Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive moni-tors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring det...

Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 31 5.0 Seagate Technology support services Internet For information regarding Seagate products and services, visit www.seagate.com . Worldwide support is available 24 hours daily by email for your questions. Presales Support: Presales@Seagate....

32 Momentus 5400.3 SATA Blade Server Product Manual, Rev. E Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative...

Momentus 5400.3 SATA Blade Server Product Manual, Rev. E 33 Index A ACA 14 acoustics 4 , 12 Address 23 Agency certification 13 Altitude 10 Altitude, nonoperating 4 Altitude, operating 4 Ambient temperature 4 , 10 ambient temperature 7 Annualized Failure Rate (AFR) 4 Areal density 3 , 6 areal density...