SEAGATE ST9160821AB - Manuals

iv Momentus 5400.3 PATA Blade Server Product Manual, Rev. B

Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® Momentus ® 5400.3 drives: • ST9160821AB • ST9120822AB • ST9100828AB • ST980815AB • ST960815AB • ST9402116AB These driv...

Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 3 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST916082...

Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 5 Table 1: Specifications for 100 and 80 Gbyte models Drive specification ST9100828AB ST980815AB Formatted Gbytes (512 bytes/sector)* 100 80 Guaranteed sectors 195,371,568 156,301,488 Bytes per sector 512 Physical read/write heads 3 2 Discs 2 ...

Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 7 Table 1: Specifications for 60 and 40 Gbyte models Drive specification ST960815AB ST9402116AB Formatted Gbytes (512 bytes/sector)* 60 40 Guaranteed sectors 117,210,240 78,140,160 Bytes per sector 512 Physical read/write heads 2 1 Discs 1 Cac...

Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 9 2.2 Formatted capacity *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.3 Default logical geometry LBA mode When addressing these dri...

10 Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 2.5 Recording and interface technology 2.6 Physical characteristics Technology Specification Interface Parallel ATA Recording method Perdendicular Recording density BPI (bits/inch typical) 835k Track density TPI (tracks/inch typical) 150k A...

Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 11 2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications below are defined as follows: • Track-to-track seek time is an average of all possi...

12 Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 2.9 Power specifications The drive receives DC power (+5V) through the interface connector. 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 12. Typical power measurements are based on an average of ...

Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 13 2.9.1.1 Typical current profile Figure 4. Typical 5V startup and operation current profile 2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. ...

14 Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Duty 50%, power-on hours (POH) of 8,760 per year (24 hours per day, 7 days ...

16 Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 2.11 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea-surements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditio...

Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 17 2.13 Reliability 2.14 Agency certification 2.14.1 Safety certification The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950 as tested by TUV North America. 2.14.2 E...

Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 19 2.15 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.15.1 European Union Restriction of Hazardous Substances (Ro...

Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 21 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static discharge precautions After unpacking, and before installation, the drive may b...

22 Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 3.2 Jumper settings 3.2.1 Master/slave configuration Use the options jumper block shown in Figure 5 to configure the drive for operation. This jumper block is the 4-pin header adjacent to pins 1 and 2 of the I/O signal pins. For additional ...

Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 23 3.3 Drive mounting You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 6 for drive mounting dimensions (dimensions in inches with mm in parentheses). Follow these impo...

Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 25 4.0 ATA interface These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–5. The drive also ...

26 Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 4.1.1 Supported ATA commands The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Draft ATA-6 Standard... Table 6: Supported commands Command name Command code...

Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 27 Security Unlock F2 H Seek 70 H Set Drive Parameters 91 H Set Features EF H Set Max Address F9 H Note: Individual Set Max com-mands are identified by the value placed in the Set Max Features register as defined to the right. Address Password...

Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 29 4.1.2 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table...

Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 33 5.0 Seagate Technology support services Internet For information regarding Seagate products and services, visit www.seagate.com . Worldwide support is available 24 hours daily by email for your questions. Presales Support: Presales@Seagate....

34 Momentus 5400.3 PATA Blade Server Product Manual, Rev. B Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative...

Momentus 5400.3 PATA Blade Server Product Manual, Rev. B 35 Index Numerics 3D Defense System 1 A acoustics 16 AFR 17 agency certification (regulatory) 17 altitude 14 ambient conditions 3 ambient temperature 11 , 14 Annualized Failure Rate 17 areal density 10 ATA interface 25 ATA-standard commands 26...