SEAGATE ST9100011FS - Manuals

Pulsar Product Manual, Rev. A iii List of Figures Figure 1. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Figure 2. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Pulsar Product Manual, Rev. A 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate Pulsar TM model drives: These drives provide the following key features: • Single Layer Cell (SLC) NAND Flash storage. • High instantaneous (burst)...

2 Pulsar Product Manual, Rev. A 1.1 About the Serial ATA interface The Serial ATA interface provides several advantages: • Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jump- ers or other configuration options. • Thinner and more flexible ca...

Pulsar Product Manual, Rev. A 3 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: Product...

Pulsar Product Manual, Rev. A 5 2.2 Formatted capacity Model Formatted capacity* Guaranteed LBAs Emulated LBA Size (Bytes) ST9200011FS 200GB 390,721,968 512 ST9100011FS 100GB 195,371,568 ST950011FS 50GB 97,696,368 *One GB equals one billion bytes when referring to drive capacity. Accessible capacity...

6 Pulsar Product Manual, Rev. A 2.4.3 Performance Notes 200GB 100GB 50GB Maximum Burst Transfer Rate 300MB/s Peak sequential 128KB read/write data transfer rate (MB/s max) [1] 240/220 Sustained sequential 128KB read/write data transfer rate (MB/s) [2] 200/100 200/60 200/30 Peak 4KB random read/write...

Pulsar Product Manual, Rev. A 7 2.6 Access time Access measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: • Page-to-page access time is an average of all possible page-to...

8 Pulsar Product Manual, Rev. A 2.8 Power specifications The drive receives DC power (+5V) through a native SATA power connector. See Figure 2 on page 20. 2.8.1 Power consumption Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on an average o...

Pulsar Product Manual, Rev. A 9 Table 2: 200GB DC power requirements ParameterRegulation +/ ‐ 5% Voltage   +5   V Current   (A) Powe r   (W) Average   Idle   Current                                        DCx 0.15 0.75     Standby                                                               DCx 0.1...

10 Pulsar Product Manual, Rev. A Table 3: 100GB DC power requirements ParameterRegulation +/ ‐ 5% Voltage   +5   V Current   (A) Powe r   (W) Average   Idle   Current                                        DCx 0.14 0.70     Standby                                                               DCx 0....

Pulsar Product Manual, Rev. A 11 Table 4: 50GB DC power requirements ParameterRegulation +/ ‐ 5% Voltage   +5   V Current   (A) Powe r   (W) Average   Idle   Current                                        DCx 0.13 0.65     Standby                                                               DCx 0.1...

12 Pulsar Product Manual, Rev. A 2.8.1.1 Typical current profiles Figure 1. Typical 5V startup and operation current profile 2.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. • Using 5-volt power, the ...

Pulsar Product Manual, Rev. A 13 2.9 Environmental specifications 2.9.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 60°C (140°F) within the operating ambient conditions. Ab...

14 Pulsar Product Manual, Rev. A 2.9.6 Vibration All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws. Vibration may be applied in the X, Y or Z axis. 2.9.6.1 Operating vibration The maximum random vibration levels that ...

Pulsar Product Manual, Rev. A 15 2.11 Reliability 2.11.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) The product shall achieve an Annualized Failure Rate - AFR - of 0.44%. AFR and MTBF are population statis-tics that are not relevant to individual units. AFR and MTBF specific...

16 Pulsar Product Manual, Rev. A 2.12 Agency certification 2.12.1 Safety certification These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so marked as to the certify agency. 2.12.2 Electromagnetic compatibility Drives that display the CE mark comply with t...

Pulsar Product Manual, Rev. A 17 Radio and television interference. This equipment generates and uses radio frequency energy and if not installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. This equipment is designed t...

18 Pulsar Product Manual, Rev. A "X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over the threshold defined by the China RoHS MCV Standard. 2.14 Corrosive environment Seagate electronic drive components pass accelerated corrosion test...

Pulsar Product Manual, Rev. A 19 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to potential hand...

20 Pulsar Product Manual, Rev. A 3.2 Configuring the drive Each drive on the Serial ATA interface connects point-to-point with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point relationship. If two drives are attached on ...

Pulsar Product Manual, Rev. A 21 3.4 Drive mounting You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 3 for drive mounting dimensions. Follow these important mounting precau-tions when mounting the drive: •...

22 Pulsar Product Manual, Rev. A 3.5 Cooling Cabinet cooling must be designed by the customer so that the ambient temperature immediately surrounding the drive will not exceed temperature conditions specified in Section 2.9.1, "Ambient temperature." The rack, cabinet, or drawer environment f...

Pulsar Product Manual, Rev. A 23 4.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. For detailed information about the...

24 Pulsar Product Manual, Rev. A 4.2 Serial ATA device plug connector pin definitions Table 6 summarizes the signals on the Serial ATA interface and power connectors. Notes: 1. All pins are in a single row, with a 1.27 mm (0.050”) pitch. 2. The comments on the mating sequence apply to the case of ba...

Pulsar Product Manual, Rev. A 25 4.3 Supported ATA commands The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification . See “S.M.A.R.T. commands” on page 3...

Pulsar Product Manual, Rev. A 27 4.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 7 on page 25. All reserved...

Pulsar Product Manual, Rev. A 37 5.0 Seagate Technology support services Online services Web For information regarding Seagate products and services, visit www.seagate.com . Worldwide support is available 24 hours daily by email for your questions. Warranty Support: http://www.seagate.com/www/en-us/...

38 Pulsar Product Manual, Rev. A Customer Service Operations Presales Support Our Presales Support staff can help you determine which Seagate products are best suited for your specific application or computer system, as well as product availability and compatibility. Technical Support Seagate techni...

Pulsar Product Manual, Rev. A 39 Index A ACA 16 acceleration 14 Access time 7 Agency certification 16 altitude 13 Ambient temperature 13 ambient temperature 7 , 8 Annualized Failure Rate (AFR) 15 ATA commands 25 Australia/New Zealand Standard AS/NZ CISPR22 16 Australian Communication Authority (ACA)...

Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100596473, Rev. A