SEAGATE ST610712DE - Manuals

ST1.3 Series Product Manual, Rev. C iii List of Figures Figure 1. ST1.3 Series IDE interface (ZIF connector) disc drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 2. ST1.3 Series breather hole location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

ST1.3 Series Product Manual, Rev. C 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® ST1.3 Series drives:• ST612712DE-12GB, ST610712DE-10GB, ST680712DE-8GB and ST660712DE-6GB disc drives with a ZIF (zero insertion force) con...

2 ST1.3 Series Product Manual, Rev. C 1.1 Disclaimer Seagate Technology LLC makes no warranties whatsoever, including any warranty of merchantability, non- infringement, fitness for any particular purpose, or any warranty otherwise arising out of any proposal, specifi-cation or sample. Seagate may n...

ST1.3 Series Product Manual, Rev. C 3 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST612712DE, ST612712DEG, ST61...

ST1.3 Series Product Manual, Rev. C 5 2.2 Formatted capacity 2.3 Default logical geometry LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above . Model Formatted capacity Guarante...

6 ST1.3 Series Product Manual, Rev. C 2.4 Recording and interface technology 2.5 Physical characteristics 2.6 Time to ready Technology Specification Interface Seagate (ZIF) Flex Connector (35-way) Recording method Perpendicular Magnetic Recording Recording density BPI (bits/inch max) 933,000 Track d...

ST1.3 Series Product Manual, Rev. C 7 2.7 Power specifications The drive receives DC power (+3.3V) through the ZIF (IDE interface) connector for ST612712DE, ST612712DEG, ST610712DE, ST610712DEG, ST680712DEG, ST680712DE, ST660712DEG and ST660712DE models. 2.7.1 Power consumption Power requirements fo...

8 ST1.3 Series Product Manual, Rev. C * During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels . 2.7.1.1 Typical current profile Figure 4. Typical 3.3V startup and operation current profile ...

ST1.3 Series Product Manual, Rev. C 9 2.7.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +3.3 volt line. Using 3.3-volt power, the drive is expected to operate with a maximum of 70 mV peak-to-peak square-wave injecte...

ST1.3 Series Product Manual, Rev. C 11 2.8 Environmental specifications 2.8.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 70°C (158°F) within the operating ambient conditio...

12 ST1.3 Series Product Manual, Rev. C 2.8.5 Shock All shock measurements in this section are carried out at drive level. For all linear shock test, operating or non-operating, the input shock level shall be measured at the frame of the disk drive at the specific location indi-cated by the ellipse i...

ST1.3 Series Product Manual, Rev. C 13 2.8.6.1 Operating sweep sine vibration The following lists the maximum operating sweep sine vibration levels that the drive may experience while meeting the performance standards specified. It will consist of a forward and backward sweep from 10 Hz to 500 Hz to...

ST1.3 Series Product Manual, Rev. C 15 2.9 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). Discrete tone penalties are added to the A-weighted sound power (LW) with the following formula only when determin-ing compliance: LWt(spec) == LW + 0....

16 ST1.3 Series Product Manual, Rev. C 2.11 Reliability Measurement type Specification Nonrecoverable read errors 1 per 10 14 bits read, max. Load/Unload (LUL) cycles (25°C) 300,000 software-controlled power on/off cycles 20,000 hard power on/off cycles Power On Hours (POH) 500 hours Warranty Per ag...

ST1.3 Series Product Manual, Rev. C 17 2.12 Agency certification 2.12.1 Safety certification The drives are recognized in accordance with UL60950-1, CAN/CSA-C22.2 No.60950-1, EN60950 and IEC 60950. 2.12.2 Electromagnetic compatibility Hard drives that display the CE mark comply with the European Uni...

18 ST1.3 Series Product Manual, Rev. C 2.12.4 China Restriction of Hazardous Substances (RoHS) Directive This product has an Environmental Protection Use Period (EPUP) of 20 years. The following table contains information mandated by China's "Marking Requirements for Control of Pollution Caused ...

ST1.3 Series Product Manual, Rev. C 19 If necessary, you should consult your dealer or an experienced radio/television technician for additional sug-gestions. You may find helpful the following booklet prepared by the Federal Communications Commission: How to Identify and Resolve Radio-Television In...

ST1.3 Series Product Manual, Rev. C 21 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static discharge precautions After unpacking, and before installation, the drive may be exposed to potentia...

22 ST1.3 Series Product Manual, Rev. C Figure 8. ST1.3 Series improper handling example • Always rest the drives on a padded, antistatic surface until you mount it in the system.• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warran...

ST1.3 Series Product Manual, Rev. C 23 • Handle the drive only by its edges or frame or designated finger grip region during mounting (see Figure 4). Figure 9. ST1.3 Series mechanical dimensions—top, bottom, side and end view

24 ST1.3 Series Product Manual, Rev. C 3.3 Mounting considerations • Use an elastic mounting material to protect drives so as to ensure that more shock can be absorbed.• There are no guides along the side for mounting. Instead, refer to figure on areas (refer to Figure 10, high- lighted in blue) whe...

ST1.3 Series Product Manual, Rev. C 25 4.0 Interface description These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–4. The drive also supports the ...

ST1.3 Series Product Manual, Rev. C 27 4.1.1 Supported ATA commands The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA commands, refer to ATA version 7 specification, Volume 1. (www.t13.org). [1] ‘X’ indicates: If the drive is in Standby mo...

28 ST1.3 Series Product Manual, Rev. C 4.1.2 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table on page 28. All ...

ST1.3 Series Product Manual, Rev. C 29 59 Number of sectors transferred during a Read Multiple or Write Multiple command 0100 H 60–61 Total number of user-addressable LBA sectors available(see Section 2.2 for related information) capacity xxxx H 62 Retired 0000 H 63 Multiword DMA active and modes su...

ST1.3 Series Product Manual, Rev. C 31 4.1.3 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-rupt. If the valu...

ST1.3 Series Product Manual, Rev. C 33 5.0 Seagate Technology support services Internet For information regarding Seagate products and services, visit www.seagate.com . Worldwide support is available 24 hours daily by email for your questions. Presales Support: [email protected] Technical Support...

34 ST1.3 Series Product Manual, Rev. C Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warranty-related...

ST1.3 Series Product Manual, Rev. C 35 Publication feedback survey We are interested in your comments and suggestions regarding this publication. Please take a few minutes to participate in our survey at the following URL: http://survey.seagate.com/survey/techpubs.nsf Thank you for your time and com...

ST1.3 Series Product Manual, Rev. C 37 Index A acoustics 15 Active mode 10 agency certification (regulatory) 17 altitude 11 ambient conditions 3 ambient temperature 11 areal density 1 , 6 ATA-standard commands 27 Australian C-Tick 17 B BPI 6 buffer 1 , 6 C cache 1 , 6 case temperature 11 CE mark 17 ...