SEAGATE ST5000AS0011 - Manuals

Seagate Archive HDD Product Manual, Rev. C 2 www.seagate.com 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following: Seagate ® Archive HDD model drives:. These drives provide the following key features:• 5900 RPM spindle speed.• TGMR recordin...

Seagate Archive HDD Product Manual, Rev. C 3 www.seagate.com 2.0 Drive Specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power.For convenience, the phrases the drive and this drive are used throughout this manual to indicate the fol...

Seagate Archive HDD Product Manual, Rev. C 5 www.seagate.com 2.2 Formatted capacity *One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.2.1 LBA mode When addressing...

Seagate Archive HDD Product Manual, Rev. C 6 www.seagate.com 2.5 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured usingdrive diagnostics. The specifications in the table below are defined as follows: • Track-to-track seek time is an average...

Seagate Archive HDD Product Manual, Rev. C 7 www.seagate.com * During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. • Spinup power Spinup power is measured from the time of power-on to th...

Seagate Archive HDD Product Manual, Rev. C 8 www.seagate.com 2.7.1.1 Typical current profiles 5TB model current profile Figure 1 Typical 5TB model 5V - 6Gb/s startup and operation current profile Figure 2 Typical 5TB model 12V - 6Gb/s startup and operation current profile

Seagate Archive HDD Product Manual, Rev. C 9 www.seagate.com 2.7.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the+12 volt line or an equivalent 15-ohm resistive load on the +5 volt line. • Using 12-volt power, the driv...

Seagate Archive HDD Product Manual, Rev. C 10 www.seagate.com 2.8.4 Altitude 2.8.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drivemounting screws. Shock may be applied in the X, Y or Z axis. 2.8.5.1 Operating shock These drives compl...

Seagate Archive HDD Product Manual, Rev. C 11 www.seagate.com 2.9 Acoustics D r i v e a c o u s t i c s a re m e a s u re d a s o v e r a l l A - w e i g h t e d a c o u s t i c s o u n d p o w e r l e v e l s ( n o p u re t o n e s ) . A l lmeasurements are consistent with ISO document 7779. Sound ...

Seagate Archive HDD Product Manual, Rev. C 12 www.seagate.com 2.12 Reliability 2.12.1 Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF) The product shall achieve an Annualized Failure Rate (AFR) of <1% (MTBF of 800K hours) when operated at annominal power and typical case tempera...

Seagate Archive HDD Product Manual, Rev. C 13 www.seagate.com Korean RRL If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC)Framework r...

Seagate Archive HDD Product Manual, Rev. C 14 www.seagate.com 2.14 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulationsrestricting certain chemical substances. 2.14.1 European Union Restriction of Hazardous Substances (R...

Seagate Archive HDD Product Manual, Rev. C 15 www.seagate.com 3.0 Configuring and Mounting the Drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may...

Seagate Archive HDD Product Manual, Rev. C 16 www.seagate.com 3.4 Drive mounting Users can mount the drive in any orientation using four screws in the side-mounting holes or four screws in thebottom-mounting holes. Refer to Figure 4 for drive mounting dimensions. Follow these important mounting prec...

Seagate Archive HDD Product Manual, Rev. C 17 www.seagate.com 4.0 About (SED) Self-Encrypting Drives Self-encrypting drives (SEDs) offer encryption and security services for the protection of stored data, commonly known as"protection of data at rest." These drives are compliant with the Trus...

Seagate Archive HDD Product Manual, Rev. C 18 www.seagate.com 4.2.3 Default password When the drive is shipped from the factory, all passwords are set to the value of MSID. This 32-byte random value can only beread by the host electronically over the interface. After receipt of the drive, it is the ...

Seagate Archive HDD Product Manual, Rev. C 19 www.seagate.com 4.6 Cryptographic Erase A significant feature of SEDs is the ability to perform a cryptographic erase. This involves the host telling the drive to changethe data encryption key for a particular band. Once changed, the data is no longer re...

Seagate Archive HDD Product Manual, Rev. C 20 www.seagate.com 5.0 SATA Interface These drives use the industry-standard Serial ATA (SATA) interface that supports FIS data transfers. It supportsATA programmed input/output (PIO) modes 0 to 4; multiword DMA modes 0 to 2, and Ultra DMA modes 0 to 6.For ...

Seagate Archive HDD Product Manual, Rev. C 21 www.seagate.com 5.3 Supported ATA commands The following table lists SATA standard commands that the drive supports.For a detailed description of the ATA commands, refer to the Serial ATA International Organization:Serial ATA Revision 3.0 ( http://www.sa...

Seagate Archive HDD Product Manual, Rev. C 23 www.seagate.com 5.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in on ...

Seagate Archive HDD Product Manual, Rev. C 25 www.seagate.com 95–99 ATA-reserved 0000 H 100–103 Total number of user-addressable LBA sectors available (see Section 2.2 for related information). These words are required for drives that support the 48-bit addressing feature. Maximum value: 0000FFFFFFF...

Seagate Archive HDD Product Manual, Rev. C 28 www.seagate.com 5.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitorspredetermined drive attributes that are susceptible to degradation over time. If self-monitoring det...

Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888EUROPE, MIDDLE EAST AND AFRICA Sea...