SEAGATE ST3200826SCE - Manuals

DB35 Serial ATA Product Manual, Rev. E 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate DB35 Serial ATA (SATA) model drives: DB35 Serial ATA • ST3400832SCE • ST3300831SCE • ST3250823SCE • ST3200826SCE These drives provide the ...

2 DB35 Serial ATA Product Manual, Rev. E 1.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation and configuration with true plug-and-play connectivity. It is not necess...

DB35 Serial ATA Product Manual, Rev. E 3 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the ST3400832SCE, ST330083...

DB35 Serial ATA Product Manual, Rev. E 5 *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. * *During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specificati...

6 DB35 Serial ATA Product Manual, Rev. E 2.4 Recording and interface technology 2.5 Physical characteristics 2.6 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as ...

DB35 Serial ATA Product Manual, Rev. E 7 2.7 Start/stop times 2.8 Power specifications The drive receives DC power (+5V and +12V) through a native SATA power connector. See Figure 5 on page 19. 2.8.1 Power consumption Power requirements for the drives are listed in the table on page 9. Typical power...

8 DB35 Serial ATA Product Manual, Rev. E 2.8.1.1 Typical current profiles Figure 1. Typical 5V startup and operation current profile Figure 2. Typical 12V startup and operation current profile Table 2: DC power requirements Power dissipation (typical) Average (watts, 25° C) 5V typ amps 12V typ amps ...

DB35 Serial ATA Product Manual, Rev. E 9 2.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line. • Using 12-volt power, the drive is expected to op...

10 DB35 Serial ATA Product Manual, Rev. E drive activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive accepts all commands and returns to Active mode when disc access is necessary. 2.9 Environmental specifications 2.9.1 Ambient temperature Ambie...

DB35 Serial ATA Product Manual, Rev. E 11 2.9.5.2 Nonoperating shock The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 300 Gs based on a nonrepetitive half-sine shock pulse of 2 msec dura...

12 DB35 Serial ATA Product Manual, Rev. E 2.11 Electromagnetic immunity When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency (RF) environments defined in the following table: 2.12 Reliability Ta...

DB35 Serial ATA Product Manual, Rev. E 13 2.13 Agency certification 2.13.1 Safety certification The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950 as tested by TUV North America. 2.13.2 Electromagnetic compatibility Hard d...

14 DB35 Serial ATA Product Manual, Rev. E Australian C-Tick (N176) If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548 1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communi-cation Authority (ACA). 2....

DB35 Serial ATA Product Manual, Rev. E 15 Seagate also has internal systems in place to ensure ongoing compliance with the RoHS Directive and all laws and regulations which restrict chemical content in electronic products. These systems include standard operat-ing procedures that ensure that restric...

DB35 Serial ATA Product Manual, Rev. E 17 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to poten...

18 DB35 Serial ATA Product Manual, Rev. E 3.2 Breather filter hole precautions This section contains information regarding the precautions to take with the breather filter hole in Seagate hard disc drives. Take the proper precautions to ensure full functionality and to prevent possible damage to the...

DB35 Serial ATA Product Manual, Rev. E 19 3.4 Serial ATA cables and connectors The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connec-tions. The cable size may be 30 to 26 AWG with a maximum length of one meter (39.37 inches). See Table 5for co...

20 DB35 Serial ATA Product Manual, Rev. E 3.5 Drive mounting You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 6 on page 20 for drive mounting dimensions. Follow these important mounting precautions when mo...

DB35 Serial ATA Product Manual, Rev. E 21 4.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. For detailed information ...

22 DB35 Serial ATA Product Manual, Rev. E 4.2 Serial ATA device plug connector pin definitions Table 5 summarizes the signals on the Serial ATA interface and power connectors.. Notes: 1. All pins are in a single row, with a 1.27 mm (0.050”) pitch. 2. The comments on the mating sequence apply to the ...

DB35 Serial ATA Product Manual, Rev. E 23 4.3 Supported ATA commands The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification. See “S.M.A.R.T. commands” o...

DB35 Serial ATA Product Manual, Rev. E 25 4.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 6 onpage 23. All ...

DB35 Serial ATA Product Manual, Rev. E 27 Note. Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported Note. See the bit descriptions below for words 63, 88, and 93 of the Identify Drive data. 129–159 Seagate-reserved xxxx H 160–254 ATA-reserved 0000 H 255...

DB35 Serial ATA Product Manual, Rev. E 29 4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive moni-tors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a fai...

DB35 Serial ATA Product Manual, Rev. E 31 5.0 Seagate Technology support services Internet For information regarding Seagate products and services, visit www.seagate.com . Worldwide support is available 24 hours daily by email for your questions. Presales Support: [email protected] Technical Supp...

32 DB35 Serial ATA Product Manual, Rev. E Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warranty-rela...

DB35 Serial ATA Product Manual, Rev. E 33 Index A ACA 14 acceleration 11 acoustics 4 , 11 Active 9 Active mode 9 actuator arm 7 AFR 12 Agency certification 13 altitude 10 Altitude, nonoperating 4 Altitude, operating 4 Ambient temperature 4 , 10 ambient temperature 6 , 7 Annualized Failure Rate (AFR)...