SEAGATE ST31000322CS - Manuals

Pipeline HD.2 Series SATA Product Manual, Rev. G iii List of Figures Figure 1. Typical 12V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure 2. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Pipeline HD.2 Series SATA Product Manual, Rev. G 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate Pipeline HD TM .2 Series model drive: These drives provide the following key features:• High instantaneous (burst) data-transfer...

2 Pipeline HD.2 Series SATA Product Manual, Rev. G 1.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include:• Easy installation and configuration with true plug-and-play connectivity. It is n...

Pipeline HD.2 Series SATA Product Manual, Rev. G 3 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following dr...

4 Pipeline HD.2 Series SATA Product Manual, Rev. G Table 1: Drive specifications summary for 1000GB models Drive specification ST31000424CS ST31000322CS Formatted Capacity (512 bytes/sector)* 1000GB Guaranteed sectors 1,953,525,168 Heads 4 Disks 2 Bytes per sector 512 Default sectors per track 63 De...

10 Pipeline HD.2 Series SATA Product Manual, Rev. G 2.2 Formatted capacity Model Formatted capacity* Guaranteed sectors Bytes per sector ST31000424CS ST31000322CS 1000GB 1,953,525,168 512 ST3500414CS ST3500312CS 500GB 976,773,168 ST3320413CS ST3320311CS 320GB 625,142,448 ST3250412CS ST3250312CS 250G...

Pipeline HD.2 Series SATA Product Manual, Rev. G 11 2.5 Physical characteristics 1000GB model 500, 320, 250 and 160GB models Maximum height 26.1mm / 1.028 in 20.20mm / 0.794 in Maximum width 101.85mm / 4.010 in Maximum length 146.99mm / 5.787 in Typical weight 615g / 1.356 lb 500 and 320GB models 42...

12 Pipeline HD.2 Series SATA Product Manual, Rev. G 2.8 Power specifications The drive receives DC power (5V or 12V) through a native SATA power connector. Refer to Figure 2 on page 22. 2.8.1 Power consumption Power requirements for the drives are listed in the table on page 9. Typical power measure...

Pipeline HD.2 Series SATA Product Manual, Rev. G 13 2.8.1.1 Typical current profiles Figure 1. Typical 12V startup and operation current profile 2.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the 12V line or an equiv...

Pipeline HD.2 Series SATA Product Manual, Rev. G 15 2.9 Environmental specifications 2.9.1 Drive case temperature Drive case temperature should be measured at the location indicated in Figure 3 on page 23. * Ambient temperature is defined as the temperature of the environment immediately surrounding...

Pipeline HD.2 Series SATA Product Manual, Rev. G 17 2.10 Acoustics emissions Drive emission of sound is measured consistent with the ECMA-74 and its referenced standards. Testing is conducted at room temperature (approximately 25 degrees C). Emission levels are reported as the total A-weighted sound...

18 Pipeline HD.2 Series SATA Product Manual, Rev. G 2.12 Reliability 2.12.1 Annualized Failure Rate (AFR) The product will achieve an Annualized Failure Rate (AFR) of 0.55% when operated in an environment of ambient air temperatures of 25 ° C. Operation at temperatures outside the specifications in ...

Pipeline HD.2 Series SATA Product Manual, Rev. G 19 Korean RRL If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requireme...

20 Pipeline HD.2 Series SATA Product Manual, Rev. G 2.14 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.14.1 European Union Restriction of Hazardous Substances (RoHS) Dire...

Pipeline HD.2 Series SATA Product Manual, Rev. G 21 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be expose...

22 Pipeline HD.2 Series SATA Product Manual, Rev. G 3.2 Configuring the drive Each drive on the Serial ATA interface connects point-to-point with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point relationship. If two driv...

Pipeline HD.2 Series SATA Product Manual, Rev. G 23 3.4 Drive mounting You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. Refer to Figure 3 for drive mounting dimensions. Follow these important mounting pre-cautions wh...

Pipeline HD.2 Series SATA Product Manual, Rev. G 25 4.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. For detailed in...

26 Pipeline HD.2 Series SATA Product Manual, Rev. G 4.2 Serial ATA device plug connector pin definitions Table 7 summarizes the signals on the Serial ATA interface and power connectors. Notes: 1. All pins are in a single row, with a 1.27mm (0.050 in) pitch. 2. The comments on the mating sequence app...

Pipeline HD.2 Series SATA Product Manual, Rev. G 27 4.3 Supported ATA commands The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA International Organization: Serial ATA Revision 2.6 (http://www.sata-...

Pipeline HD.2 Series SATA Product Manual, Rev. G 29 4.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 8 on pa...

30 Pipeline HD.2 Series SATA Product Manual, Rev. G 60–61 Total number of user-addressable LBA sectors available(Refer to Section 2.2 for related information.)*Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,455 sectors, 137GB). Drives with capacities over 137GB will have 0FFFFF...

Pipeline HD.2 Series SATA Product Manual, Rev. G 31 Note. Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported Note. Refer to the bit descriptions below for words 63, 84, and 88 of the Identify Drive data. 100–103 Total number of user-addressable LBA sec...

Pipeline HD.2 Series SATA Product Manual, Rev. G 35 5.0 Seagate Technology support services Internet For information regarding Seagate products and services, visit www.seagate.com . Worldwide support is available 24 hours daily by email for your questions. Presales Support: [email protected] Tech...

36 Pipeline HD.2 Series SATA Product Manual, Rev. G Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for war...

Pipeline HD.2 Series SATA Product Manual, Rev. G 37 Index A ACA 19 acceleration 16 acoustics 17 Active mode 14 AFR 18 agency certification 18 altitude 15 ambient temperature 11 , 12 Annualized Failure Rate (AFR) 18 areal density 1 , 10 ATA commands 27 Australia/New Zealand Standard AS/NZ CISPR22 19 ...

Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100529372, Rev. G, Printed in U.S.A.