SEAGATE ST136403LW/LC - Manuals

Cheetah 36 Installation Guide, Rev. A 3 as some resistors and capacitors, may be damaged or degradedby exposure to static electricity. Electrostatic damage to electronic devices may be caused by thedirect discharge of a charged conductor or by exposure to thestatic fields surrounding charged objects...

8 Cheetah 36 Installation Guide, Rev. A Regulatory agency compliance Electromagnetic susceptibilityAs a component assembly, the drive is not required to meet anysusceptibility performance requirements. It is the responsibility ofthose integrating the drive within their systems to perform thosetests ...

10 Cheetah 36 Installation Guide, Rev. A General description Cheetah 36 SCSI disc drives are high-speed, random-accessdigital-data storage devices capable of operating in single-ended(SE) or low voltage differential (LVD) modes. This multimode capability allows you to use this drive in systemsthat u...

Cheetah 36 Installation Guide, Rev. A 11 Single-ended and low voltage differential modes This drive incorporates two different transceivers to allow you touse it in systems which use single-ended (SE) drivers andreceivers, or in low voltage differential (LVD) capable systemswhich use LVD drivers and...

12 Cheetah 36 Installation Guide, Rev. A Data bus widths These drives have a wide (16-bit) SCSI data bus. You can usethese drives on a non-wide (8-bit) data bus if you provide propertermination to the upper eight data lines. This is often referred toas providing “high-9 termination” (the other bit i...

14 Cheetah 36 Installation Guide, Rev. A . Figure 2. Suggested air flow Abbildung 2. Empfohlener Luftstromverlauf Above unit Under unit Note. Air flows in the direction shown (back to front) or in reverse direction (front to back) Above unit Under unit Note. Air flows in the direction shown or in re...

Cheetah 36 Installation Guide, Rev. A 15 Characteristics ST136403LW/LC Interface Ultra2 SCSI 1 Capacity Unformatted (Gbytes)Formatted (Gbytes) 2 43.236.4 Recording Cylinders (user)Read/write data headsAvg bytes/track 9,80124153,284 - 229,045 Access time 3 Average read (msec)Average write (msec) 6.15...

Cheetah 36 Installation Guide, Rev. A 17 How to install the drive This installation guide provides step-by-step instructions to makeyour drive installation as easy as possible. Follow the installationsteps listed for your drive model as listed below: LW models (use the installation steps beginning b...

18 Cheetah 36 Installation Guide, Rev. A Figure 3. Setting the SCSI ID on LW model drives SCSI ID = 0 (default) Note: [1] Do not remove cover from pins 13 through 20 (darkened area). Jumper Plug (enlarged toshow detail) J6 DriveFront Pin 1 SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 ...

Cheetah 36 Installation Guide, Rev. A 19 2. Configure termination. If you are installing the drive in a system that has other SCSIdevices installed, terminate only the end devices on theSCSI bus. Figure 4 shows the three most common termination configu-rations. LW model drives do not have internal t...

20 Cheetah 36 Installation Guide, Rev. A Figure 4. SCSI bus termination Internal SCSI device Internal SCSI device Controller External SCSI device External SCSI device External SCSIcable Internal SCSI cable Terminate Internal SCSI device Internal SCSI device Controller Internal SCSI cable Terminate I...

24 Cheetah 36 Installation Guide, Rev. A Figure 7. Additional jumper options SE DS M E W P PD RES RES TP J2 Pin 1 Pin 2 Enable parity check of SCSI bus (default). Disable parity check. Reserved Parity Check option Write protect = Off (enables writing – default). Write protect = On (disables writing)...

26 Cheetah 36 Installation Guide, Rev. A Figure 8. Connecting cables to the drive

Cheetah 36 Installation Guide, Rev. A 27 [1] “X” means up to 15 devices on the SCSI bus.[2] External terminator. Used only on end “LW” drive. Use only SPI-2- compliant active LVD terminators on SCSI Ultra2 buses. Figure 9. Multiple-drive connection to host adapter Terminated Host Adapter PCB Pin 1 (...

Cheetah 36 Installation Guide, Rev. A 29 Additional connector on LW model drives LW model drives have a connector located between the SCSI I/Oconnector and the DC power connector to allow you to set theSCSI ID and connect LEDs from the back of the drive. You arenot required to use this connector, bu...

30 Cheetah 36 Installation Guide, Rev. A LC model installation 1. Set the SCSI ID on the drive. Determine which SCSI IDs are already being used in thesystem and then assign the disc drive a SCSI ID that isn’talready being used. Use the J6 connector located on thefront of the drive to set the SCSI ID...

Cheetah 36 Installation Guide, Rev. A 31 Figure 12. Setting the SCSI ID on LC model drives SCSI ID = 0 (default) Note: [1] Do not remove cover from pins 13 through 20 (darkened area). Jumper Plug (enlarged toshow detail) J6 DriveFront Pin 1 SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5...

34 Cheetah 36 Installation Guide, Rev. A Figure 13. Additional jumper options SE DS M E W P PD RES RES RES J2 Pin 1 Pin 2 Enable parity check of SCSI bus (default). Disable parity check. Reserved Parity Check option Write protect = Off (enables writing – default). Write protect = On (disables writin...

Cheetah 36 Installation Guide, Rev. A 35 4. Mount the drive in the host system. To mount an LC model drive, plug the drive into the system’ssingle connector attachment (SCA) position on the system’sbackplane. The SCA connector on the drive contains inter-face and power functions, so it does not requ...

Cheetah 36 Installation Guide, Rev. A 37 5. Format the drive. Important information about formatting the drive • The drive has been low level formatted at the factory.You do not need to perform another low level format onthis drive unless you decide to perform certain diagnos-tics through the host a...

38 Cheetah 36 Installation Guide, Rev. A Note. Hardware platform, operating system, and hostadapter variations can limit access to the full capac-ity of this and other high capacity drives. Refer toyour system, host adapter, or drive utility documen-tation for detailed instructions. DOS, Windows 3.1...

Cheetah 36 Installation Guide, Rev. A 39 the drive you want to partition. Make sure that your newdrive is selected. If you accidently repartition your oldhard drive, you will erase all data on the drive. d. Press 1 to select “Create DOS partition or logical DOS drive” and then press the ENTER key. e...

Cheetah 36 Installation Guide, Rev. A 41 Seagate Technology support services Online Services Internet F o r o n l i n e i n f o r m a t i o n a b o u t S e a g a t e p r o d u c t s , v i s i twww.seagate.com or e-mail your disc or tape questions to: Presales Support: Disc: http://www.seagate.com/su...

42 Cheetah 36 Installation Guide, Rev. A phone numbers, commonly asked questions, troubleshootingtips and specifications for disc drives and tape drives 24 hoursdaily. International callers can reach this service by dialing +1-405-936-1234. SeaFAX ® is Seagate's automated FAX delivery system. Using ...

Cheetah 36 Installation Guide, Rev. A 43 specialist from 8:00 A.M. to 12:15 P.M. and 1:30 P.M. to 6:00P.M. (central time) Monday through Friday. Customer Service (CSO) Warranty Repair Seagate offers worldwide customer support for Seagate drives.Seagate direct OEM, Distribution and System Integrator ...

44 Cheetah 36 Installation Guide, Rev. A Warranty Repair USA/Canada 1-800-468-3472 FAX: +1-405-949-6740 Latin America +1-405-949-7758 FAX: +1-405-949-6738 Authorized Service Centers Brazil MA Informatica +55-21-516-6649 FAX: +55-21-516-5280 Canada Memofix +1-905-660-4936 FAX: +1-905-660-4951 Adtech ...

Cheetah 36 Installation Guide, Rev. A 45 Norway 800-113 91 Poland 00 800-311 12 38 Spain 900-98 31 24 Sweden 0 207 90 073 Switzerland 0 800-83 84 11 Turkey 00 800-31 92 91 40 United Kingdom 0 800-783 5177 SeaBOARD Germany +49-89-1409331 Fax Services—All European Countries Presales/Technical Support/...

46 Cheetah 36 Installation Guide, Rev. A SeaFAX Australia +61-2-9756-5170 Warranty Repair Japan +81-3-5462-2904 FAX: +81-3-5462-2979 Asia/Pacific and +65-485-3595 FAX: +65-488-7503 Australia