SEAGATE 100665905 - Manuals

Momentus XT Product Manual, Rev. D iii List of Figures Figure 1. Typical +5V only startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 2. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Momentus XT Product Manual, Rev. D 1 1.0 Seagate Technology support services SEAGATE ONLINE SUPPORT and SERVICES For information regarding products and services, visit http://www.seagate.com/www/en-us/about/contact_us/ Available services include: Presales & Technical support Global Support Servi...

2 Momentus XT Product Manual, Rev. D 2.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate Momentus ® XT model drives: These drives provide the following key features: • 7200-RPM spindle speed. • 32MB buffer. • Quiet operation. Fluid...

Momentus XT Product Manual, Rev. D 3 2.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation and configuration with true plug-and-play connectivity. It is not normally n...

4 Momentus XT Product Manual, Rev. D 3.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. 3.1 Specification summary table The specifications listed in this table are for quick reference. For details on specification me...

6 Momentus XT Product Manual, Rev. D 3.2 Formatted capacity Model Formatted capacity* Guaranteed sectors Bytes per sector ST750LX003 750GB 1,465,149,168 4K emulated @ 512 ST500LX003 500GB 976,773,168 *One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary...

Momentus XT Product Manual, Rev. D 7 3.3 Default logical geometry Cylinders Read/write heads Sectors per track 16,383 16 63 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above ....

8 Momentus XT Product Manual, Rev. D 3.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: • Track-to-track seek time is an average of all possible single...

Momentus XT Product Manual, Rev. D 9 • Idle mode power Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in a random track location. • Standby mode During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and...

10 Momentus XT Product Manual, Rev. D 3.9.1.1 Typical current profile Figure 1. Typical +5V only startup and operation current profile

12 Momentus XT Product Manual, Rev. D • Idle and Standby timers Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and begins counting down from its specified delay times to zero. If the standby timer reaches zero before any drive activity is re...

Momentus XT Product Manual, Rev. D 13 3.10.6.2 Nonoperating shock The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse of 2 ms duration....

14 Momentus XT Product Manual, Rev. D 3.12 Electromagnetic immunity When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency (RF) environments defined in the following table: 3.13 Reliability Measur...

Momentus XT Product Manual, Rev. D 15 3.14 Agency certification 3.14.1 Safety certification The drives are recognized in accordance with UL 60950-1 and CSA C22.2 (950) and meet all applicable sec-tions of IEC 60950-1 and EN60950-1 as tested by TUV North America. 3.14.2 Electromagnetic compatibility ...

16 Momentus XT Product Manual, Rev. D 3.14.3 FCC verification These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an external device). As such, each drive is considered to be a subassembly even when it is individually mar-keted to the cus...

Momentus XT Product Manual, Rev. D 17 3.15.2 China Restriction of Hazardous Substances (RoHS) Directive This product has an Environmental Protection Use Period (EPUP) of 20 years. The following table contains information mandated by China's "Marking Requirements for Control of Pollution Caused b...

18 Momentus XT Product Manual, Rev. D 4.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 4.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to potential...

Momentus XT Product Manual, Rev. D 19 4.2 Configuring the drive Each drive on the Serial ATA interface connects in a point-to-point configuration with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point relationships. If tw...

20 Momentus XT Product Manual, Rev. D 4.4 Drive mounting You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 3 for drive mounting dimensions. Follow these important mounting precautions when mount-ing the drive: • Allow a minim...

Momentus XT Product Manual, Rev. D 21 5.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. The drive also supports the u...

22 Momentus XT Product Manual, Rev. D 5.2 Serial ATA device plug connector pin definitions Table 7 summarizes the signals on the Serial ATA interface and power connectors. 1. All pins are in a single row, with a 1.27 mm (0.050”) pitch. 2. The comments on the mating sequence apply to the case of back...

Momentus XT Product Manual, Rev. D 23 5.3 Supported ATA commands The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification . See “S.M.A.R.T. commands” on p...

Momentus XT Product Manual, Rev. D 25 5.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table on page 27. All r...

26 Momentus XT Product Manual, Rev. D 60–61 Total number of user-addressable sectorsThis field contains a value that is one greater than the total number of user-addressable sectors. The maximum value that shall be placed in this field is 0FFFFFFFh. The 0FFFFFFFh value applies to all capacities over...

28 Momentus XT Product Manual, Rev. D 5.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-rupt. If the value...

Momentus XT Product Manual, Rev. D 29 SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4 H ) that elimi- nates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at: http://seatools.seagate.com . This drive...

Momentus XT Product Manual, Rev. D 29 Index A ACA 14 acoustics 5 , 12 Active mode 10 Address 22 AFR 13 Agency certification 14 Altitude 11 Altitude, nonoperating 5 Altitude, operating 5 Ambient temperature 5 , 11 ambient temperature 8 Annualized Failure Rate 13 Annualized Failure Rate (AFR) 5 Areal ...

Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA S...