SEAGATE 100529372 - Manuals

iv Pipeline HD.2 Series SATA Product Manual, Rev. J

Video 3.5 HDD Product Manual, Rev. J 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate Seagate Video 3.5 (formerly Pipeline ® HD.2) model drive: These drives provide the following key features:• High instantaneous (burst) data-...

2 Video 3.5 HDD Product Manual, Rev. J 1.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include:• Easy installation and configuration with true plug-and-play connectivity. It is not necessary...

Video 3.5 HDD Product Manual, Rev. J 3 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive model: 2...

4 Video 3.5 HDD Product Manual, Rev. J Table 1: Drive specifications summary for 1000GB models Drive specification ST31000424CS ST31000322CS Formatted Capacity (512 bytes/sector)* 1000GB Guaranteed sectors 1,953,525,168 Heads 4 Disks 2 Bytes per sector 512 Default sectors per track 63 Default read/w...

10 Video 3.5 HDD Product Manual, Rev. J 2.2 Formatted capacity Model Formatted capacity* Guaranteed sectors Bytes per sector ST31000424CS ST31000322CS 1000GB 1,953,525,168 512 ST3500414CS ST3500312CS 500GB 976,773,168 ST3320413CS ST3320311CS 320GB 625,142,448 ST3250412CS ST3250312CS 250GB 488,397,16...

12 Video 3.5 HDD Product Manual, Rev. J 2.8 Power specifications The drive receives DC power (5V or 12V) through a native SATA power connector. Refer to Figure 2 on page 22. 2.8.1 Power consumption Power requirements for the drives are listed in the table on page 9. Typical power measurements are ba...

Video 3.5 HDD Product Manual, Rev. J 13 2.8.1.1 Typical current profiles Figure 1. Typical 12V startup and operation current profile 2.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the 12V line or an equivalent 15-ohm...

14 Video 3.5 HDD Product Manual, Rev. J 2.8.4 Power management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes: • A...

Video 3.5 HDD Product Manual, Rev. J 15 2.9 Environmental specifications This section provides the temperature, humidity, shock, and vibration specifications. Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Above 1000ft. (305 meters), the maxim...

Video 3.5 HDD Product Manual, Rev. J 17 2.10 Acoustics emissions Drive emission of sound is measured consistent with the ECMA-74 and its referenced standards. Testing is conducted at room temperature (approximately 25 degrees C). Emission levels are reported as the total A-weighted sound power level...

18 Video 3.5 HDD Product Manual, Rev. J 2.12 Reliability 2.12.1 Annualized Failure Rate (AFR) The product will achieve an Annualized Failure Rate (AFR) of 0.55% when operated in an environment of ambient air temperatures of 25 ° C. Operation at temperatures outside the specifications in Section 2.9 ...

Video 3.5 HDD Product Manual, Rev. J 19 Korean RRL If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the R...

20 Video 3.5 HDD Product Manual, Rev. J 2.14 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.14.1 European Union Restriction of Hazardous Substances (RoHS) Directive The Eu...

Video 3.5 HDD Product Manual, Rev. J 21 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to potenti...

22 Video 3.5 HDD Product Manual, Rev. J 3.2 Configuring the drive Each drive on the Serial ATA interface connects point-to-point with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point relationship. If two drives are attac...

Video 3.5 HDD Product Manual, Rev. J 23 3.4 Drive mounting You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. Refer to Figure 3 for drive mounting dimensions. Follow these important mounting pre-cautions when mounting ...

Video 3.5 HDD Product Manual, Rev. J 25 4.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. For detailed information ab...

26 Video 3.5 HDD Product Manual, Rev. J 4.2 Serial ATA device plug connector pin definitions Table 7 summarizes the signals on the Serial ATA interface and power connectors. Notes: 1. All pins are in a single row, with a 1.27mm (0.050 in) pitch. 2. The comments on the mating sequence apply to the ca...

Video 3.5 HDD Product Manual, Rev. J 27 4.3 Supported ATA commands The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA International Organization: Serial ATA Revision 2.6 (http://www.sata-io.org). See...

Video 3.5 HDD Product Manual, Rev. J 29 4.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 8 on page 27. All r...

Video 3.5 HDD Product Manual, Rev. J 31 Note. Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported Note. Refer to the bit descriptions below for words 63, 84, and 88 of the Identify Drive data. 100–103 Total number of user-addressable LBA sectors availab...

34 Video 3.5 HDD Product Manual, Rev. J 4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive moni-tors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failu...

Video 3.5 HDD Product Manual, Rev. J 35 5.0 Seagate Technology support services For information regarding online support and services, visit http://www.seagate.com/www/en-us/about/ contact_us/ Available services include: • Presales & Technical support • Global Support Services telephone numbers ...

36 Video 3.5 HDD Product Manual, Rev. J Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warranty-relate...

Video 3.5 HDD Product Manual, Rev. J 37 Index A ACA 19 acceleration 16 acoustics 17 Active mode 14 AFR 18 agency certification 18 altitude 15 ambient temperature 11 , 12 Annualized Failure Rate (AFR) 18 areal density 1 , 10 ATA commands 27 Australia/New Zealand Standard AS/NZ CISPR22 19 Australian C...

Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, USA Publication Number: 100529372, Rev. J